http://www.owltechcctv.com
FeaturePartItem Remark
Power Input AC100-AC240 ~50/60Hz
Charging State
Keep the power off state during transportation
Accessory: Converter (DV12V & Network plug) for IPC
connection
Before connecting solar pane, make sure the power switch
to "O" state,
connect negative electrode first, then the positive electrode.
When IPC Working LED is Always Off & Always On, if I
PC power LED (F) is checked normal, please check if IPC
wiring and connectors are proper.
IPC came with waterproof connector, need to put
waterproof head onto Cat5e / Cat6 cable in advance,
then perform crimping the crystal head.
If the microwave power indicate abnormal, you need to
contact the engineers, returned to factory for repair.
According to the signal strength, to adjust the angle and
direction inbetween the microwave receive and transmit.
If there is no output of solar panel, please check if there
is crack in solar panel, wiring is correct or cable is
damaged.
Should power supply irregular occurs, if there is
sufficient sunshine, the device will be charged up
automatically and recovered, IPC & Microwave
will enter normal working stage when battery is recovered
to normal level, human intervention is not required. If it is
unable to recover for a long time, please check if there is
crack in solar panel, wiring is correct or cable is damaged.
Should power supply irregular occurs, if there is
insufficient sunshine, need to remove the microwave
device, charge via the external charging port.
For several days without or insufficient sunlight, battery
too low will happen. When sunlight restored, the solar
panels will charge up the battery, according to sunlight
conditions, it takes 5-15 days to fully charge the battery.
SPMW300-500 charging time 6 hours can be filled, do
not charge more than 10 hours
SPMW300-1000 charging time 12 hours can be filled,
do not charge more than 20 hours
After fully charged, unplug the power cord and turn the
power switch to "O" state, charging indicator stays On
for a while then Off and this is a normal phenomenon
due to a small electric charge by capacitor within
the charging device, charging indicator will turn Off after
discharge.
Make sure Power Switch is Off before charging, plug in
the charging power cord, and then Switch to charging
state
After fully charge, first unplug the charging power cord,
and turn the Switch to Off state
RX+
RX-
TX+
+12V
+12V
TX-
GND
GND
1
2
3
4
5
6
7
8
Solar Panel - positive
Solar Panel - negative
+
-
IPC working properly
IPC No access to IPC
IPC exception
IPC is working properly
No access to IPC
IPC exception
Flash
Always Off
Always On
Flash
Always Off
Always On
Microwave signal normal
Microwave signal abnormal
Flash
Always On or Off
Microwave signal strength, H1 (weak),
H4 (strong)
Receiving device not found
H1-H4 Always ON
H1 to H4 Flashing Cycle
On
Off
Solar panel power output normal
Solar panel no power output
Microwave power supply normal
Microwave power supply abnormal
IPC power supply normal
IPC power supply abnormal
On
Off
On
Off
Battery Low, charging
Battery Middle, charging
Battery is fully charged
Red
Pink
Green
Battery Level Full
Battery Level above 75%
Battery Level above 50%
Battery Level above 25%
Battery Level below 25%
Solar Panel is charging the battery
Power On
Power Off
On
On
On
On
Flash
D1 to D4 Flashing Cycle
Battery Level Indicator
-
O
=
M
IPC Port
L
Solar Panel Input Port
IPC2 Working LED K
J
IPC1 Working LED
I
Microwave Working
LED
G
Solar Panel Power-On
LED
F
PIC Power-On LED
E
Microwave Power-On
LED
C
Charging Indicator
B
Charging Port
A
Power Switch
D1
H1 H2
H3 H4
Microwave Signal
Strength Indicator
D4
D3
D2
