Bosch APC-AMC2-4W User manual

AMC2 4W
APC-AMC2-4W | APC-AMC2-4WCF | APC-AMC2-4WUS
en Installation manual

AMC2 4W | en 3
Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09
Remarks
This hardware is part of a security system. Access shall be lim-
ited to authorized persons only.
Some states do not allow the exclusion or limitation of implied
warranties, or limitation of liability for incidental or consequen-
tial damages, so the above limitation or exclusion might not
apply to you.
Bosch Security Systems retains all rights not expressly granted.
Nothing in this license constitutes a waiver of Bosch’s rights
under the U.S. Copyright laws or any other federal or state law.
If you have any questions concerning this license, please, write
to:
Bosch Access Systems GmbH
Adenauerstr. 20 / A3
D-52146 Würselen
Germany.

4en | AMC2 4W
F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems
Table of Contents
1 Please read carefully 7
1.1 Explanation of Used Symbols 7
1.2 Internet 7
2 Safety Instructions 8
2.1 Important Safety Notes 8
2.2 FCC & ICES Information 10
2.3 Safety Precautions 11
2.4 Unpacking 12
3 Introduction 13
3.1 Description of the AMC2 4W 13
3.2 Equipment Configuration 15
3.3 Performance Characteristics 18
3.4 System Overview 19
4 Technical Data 20
5 Installing 22
5.1 Mounting 22
5.2 Demounting 23
5.3 Opening the AMC2 4W Case 24
5.4 Cabling 25
5.4.1 Conductor data for connection to power supply 25
5.4.2 Grounding and Shielding the Host Interface 26
5.4.3 Grounding and Shielding the Extension Interface 28
5.5 Connecting Power Supply 28
5.6 RS-485 Host Interface 30
5.6.1 RS-485 Two Wire Connection 32
5.6.2 RS-485 Four Wire Connection 33
5.6.3 DIL Switch Address Selector 34
5.7 RS-232 Host Interface 36
5.8 Ethernet Interface 37

AMC2 4W | en 5
Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09
5.9 RS-485 Extension Module Bus 39
5.10 Wiegand Interface for Card Readers 39
5.11 Connecting Relay Outputs 41
5.12 Connecting Analog Input Devices 44
5.13 Tamper Protection 46
6Operating 48
6.1 Status Display of the AMC2 4W 48
6.2 Configuring the Ethernet Interface 50
6.3 Resetting the AMC2 4W 50
6.3.1 Resetting the Software 50
6.3.2 Resetting the Network Configurations 51
7 Appendix 53
7.1 Connecting Diagrams 53
7.2 Legend 57
8Index 58

6en | AMC2 4W
F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems

AMC2 4W Please read carefully | en 7
Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09
1 Please read carefully
1.1 Explanation of Used Symbols
Throughout this document, helpful tips, important notes, cau-
tions and warnings will be presented for the reader to keep in
mind. These appear different from the rest of the text as fol-
lows:
1.2 Internet
If you are interested in further information on this product or
information on other products, please, refer to our website at
http://www.bosch-security-systems.com.
!
CAUTION! or WARNING!
These warn the operator that damage to the program or equip-
ment might occur.
i
NOTE!
Important Notes – must be followed for successful operation
and programming. Tips and shortcuts might also be included
here.

8en | Safety Instructions AMC2 4W
F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems
2 Safety Instructions
2.1 Important Safety Notes
1. Read, Follow, and Retain Instructions - All safety and
operating instructions must be read and followed properly
before putting the unit into operation. Retain instructions
for future reference.
2. Consider all Warnings - Adhere to all warnings on the unit
and in the operating instructions.
3. Accessories - Use only accessories recommended by the
manufacturer or those sold with the product. Accessories
not recommended by the manufacturer shall not be used,
as they may cause hazards.
4. Installation Precautions - Do not place this unit on an
unstable stand, tripod, bracket, or mount. The unit may
fall, causing serious injury to persons and damage to the
unit. Mount the unit according to the manufacturer’s
instructions.
5. Service - Do not attempt to service this unit by yourself.
Opening or removing covers may expose you to dangerous
voltages or other hazards. Refer all servicing to qualified
service personnel.
6. Damage Requiring Service - Disconnect the unit from the
main AC or DC power source and refer servicing to quali-
fied service personnel under the following conditions:
•When the power supply cord or plug is damaged.
•If liquid has been spilled or an object has fallen into
the unit.
•If the unit has been exposed to water and/or inclem-
ent weather (rain, snow, etc.).
•If the unit does not operate normally, when following
the operating instructions. Adjust only those controls
specified in the operating instructions. Improper
adjustment of other controls may result in damage,
and require extensive work by a qualified technician
to restore the unit to normal operation.

AMC2 4W Safety Instructions | en 9
Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09
•If the unit has been dropped or the cabinet damaged.
•If the unit exhibits a distinct change in performance,
this indicates that service is needed.
7. Replacement Parts - When replacement parts are
required, the service technician shall use replacement
parts that are specified by the manufacturer. Unauthorized
substitutions may result in fire, electrical shock or other
hazards.
8. Safety Check - Upon completion of service or repair work
on the unit, ask the service technician to perform safety
checks to ensure that the unit operates properly
9. Power Sources - Operate the unit only from the type of
power source indicated on the label. If unsure of the type
of power supply to use, contact your dealer
•For units intended to operate from battery power,
refer to the operating instructions.
•For units intended to operate with External Power
Supplies, use only the recommended approved power
supplies.
•For units intended to operate with a limited power
source, this power source must comply with EN/UL
60950. Substitutions may damage the unit or cause
fire or shock.
•For units intended to operate at 12/24V DC normal
input voltage is 12/24V DC. Voltages applied to the
unit’s power input shall not exceed 15/30V DC.
10. Lightning - For added protection during a lightning storm,
or when this unit is left unused for long periods of time,
disconnect the unit from power. This will prevent damage
to the unit due to lightning and excessive power line
surges.
11. Restricted Access Locations are required for the installa-
tion.

10 en | Safety Instructions AMC2 4W
F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems
2.2 FCC & ICES Information
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC rules. The limits are designed to provide reasonable pro-
tection against harmful interference in a residental installation.
This equipment generates, uses and can radiate radio fre-
quency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one
or more of the following measures:
1. Reorient or relocare receiving antenna
2. Increase the separation between the equipment and the
receiver
3. Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected
4. Consult the dealer or an experienced radio/TV technician
for help