Oxhark Flame VL-M02DB72 User manual

1
Model#: VL-M02DB72
VL-M02LB72
USE AND CARE GUIDE
FIREPLACE WITH 2 GLASS DOORS
IMPORTANT
Questions, problems, assembly help, missing parts?
We will gladly help and ship your replacement parts free of charge.
If you have any question related to product, please free to contact our customer
service mail: [e-mail]
IMPORTANT
THIS INSTRUCTION CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.

2
WARNING
-Do not allow children to climb on unit.
-Serious or fatal crushing injuries can occur from furniture tip-over, to prevent this furniture from
tipping over it must be permanently fixed to the wall.
-Fixing devices for the wall are not included since different wall materials require different types of
fixing devices. Use fixing devices suitable for the walls in your home. For advice on suitable fixing
systems, contact your local specialized dealer.
-This unit contains small parts which can be swallowed by children and pets. Keep children and pets
away during assembly. To avoid danger of suffocation always keep plastic bags away from children
and pets.
BEFORE YOU START
-Separate and count all parts and hardware.
-Have the following tool: Flat head Screwdriver, #2 Philips Head Screwdriver.
-If using a power tool, please be ware to slow down and stop when screw is
tight. Failure to do so may result in stripping the screw.
-Requires two people for assembly.
-The product is KD construction. Do not fully tighten the bolts before all are
completely lined up and inserted into holes. Loosen the bolts and make sure
all bolts are lined up and inserted into the holes.
CAM LOCK FASTENING SYSTEM
！
12
34
Make proper orientation of
CAM LOCK when inserting AM BOL TC

3
HARDWARE PART LIST
NOT SHOW ACTUAL SIZE
Cam Lock Cam Bolt
Wood Dowel Screw
Screw Screw

4
HARDWARE PART LIST
NOT SHOW ACTUAL SIZE
Shelf Support Bolt
Hinge Handle
Screw Angle Bracket

5
BOARD IDENTIFICATION
NOT SHOW ACTUAL SIZE

6
STEP 1
1. Unpack the unit and confirm that you have all the hardware and required parts. Assembly the unit on a carpeted
floor or the empty carton to avoid any scratch.
2. Securely screw the Cam Bolts (2) into the designated small holes of Part (O), Part (P), Part (R), Part (Q) as shown.
Fully tighten with a Phillips screwdriver.
3. Insert the Wood Dowels (3) into the Part (O), Part (P), Part (R), Part (Q) as shown.

7
STEP 2
1. Align and attach the Part (O) and Part (P) to the Part (Q) by using the Cam Locks (1).
2. Then attach the Part (R) to the Part (O) and Part (P) by using the Cam Locks (1) as shown.

8
STEP 3
1. Securely screw the Cam Bolts (2) into the designated small holes of Bottom (B) as shown.

9
STEP 4
1. Attach the assembled Part (O), Part (P), Part (Q) and Part (R) to the Bottom (B) with sixteen Cam Locks (1).
2. Then turn it over and securely screw the Cam Bolts (2) into the designated small holes of Bottom (B) as shown.

10
STEP 5
1. Insert the Wood Dowels (3) into the Part (K), Part (G), Part (E) and Part (F) as shown.
2. Securely screw the Cam Bolts (2) into the designated small holes of Upper Side Verticals (J) as shown.

11
STEP 6
1. Attach the Upper Side Verticals (J) to the Left Upper Side (E) and Right Upper Side (F) with the Cam Locks (1) as
shown.

12
STEP 7
1. Securely screw the Cam Bolts (2) into the designated small holes of Top (A) as shown.

13
STEP 8
3. Attach the Upper Side (E) and (F) to the Top (A) with four Cam Locks (1) as shown.
4. Fasten the Upper Partition (G) to the Top (A) with two Cam Locks (1) as shown.

14
STEP 9
1. Position the Center Shelf (D) onto the inserted Wood Dowels and insert six Screws (4) through the countersunk
holes on the Center Shelf (D) and screw into the Upper Side (E), (F) and Upper Partition (G) as shown.

15
STEP 10
1. Securely screw the Cam Bolts (2) into the designated small holes of back side of Center Shelf (D) as shown.
2. Position the Rail (K) onto the inserted Wood Dowels and insert three Screws (4) through the countersunk holes
on the Rail (K) and screw into the Center Shelf (D) as shown.

16
STEP 11
1. Insert the Wood Dowels (3) into the Lower Sides (H), and Lower Partitions (I) as shown.
2. Securely screw the Cam Bolts (2) into the designated small holes of Lower Partition Verticals (L) as shown.

17
STEP 12
1. Attach the Lower Partition Verticals (L) to the Lower Partitions (I) with four Cam Locks (1) as shown.

18
STEP 13
1. Attach the Lower Sides (H) and Lower Partitions (I) to the Bottom (B) with eight Cam Locks (1) as shown.

19
STEP 14
1. Attach the assembly upper frame to the Lower Sides (H) and Lower Partitions (I) with eight Cam Locks (1) as shown.

20
STEP 15
1. Pick up the Upper Back Panel (M) and align the pre-drilled holes against the upper long edge with pilot holes on
the back stretcher of the Top (A). Attach the Back Panel (M) in place using the provided Screws (6).
2. Attach two Lower Back Panels (N) to the mantel base with the provided Screws (6) as shown.