OXO MultiBEAM LED-Variable White-Zoom User manual

MultiBEAM LED-Variable
White-Zoom
KEEP THIS MANUAL FOR FUTURE NEEDS ( E

Thank you for your patronage. We are confident that our excellent products and service can
satisfy you.
Foryour own safety,please r~ad this user manual carefullybefore installing the device.
CAUTION
Keep this device away from rain and moisture
CAUTION
Unplug mainslead bef<:>reopening the housing.
Every person involved with the installation,operation and maintenance of this device has to
- be qualified
- follow the instructions of thismanual
-consider this manual to be part of the total product
- keep this manual for the entire service life of the product
- pass this manual on to every further owner or user of the product
- download the latestversion of the user manual from theInternet
Thank you for having chosen thisprofessional LED lighting.
Youwill see you have acquiredapowerful andversatiledevice.
Unpack the device. Insidethe box you should find:
1. Thefixture device
2. Onepower cables
3. One XLR connection cable
4.One safety rope and this manual
Belows are the optional accessories, please purchase from your local dealer if needed
1.Barn-door
2.Frost filter
Please check carefullythat thereisno damage caused bytransportation. Should there beany,
consult your dealer and don't install this device .
•DMX channel: 6 channels
• Equippedwith 36x3WLEOS: 12 x Cool-White,24x Warm-White
•100 000 hoursLED life
• The LEOScan be controlled individually
• Automatic power supplyadaption between 100V and 240 Volts without power selector
•Programmable color-change speed and strobe effect

• DMX-controlled operation or stand alone operation with Master/Slave-function
• Strobe-effect with I-18 flashes per second
• Advantages ofLED-technology:Extremelylonglife,19wpowerconsumption,minimal heat emission,defact
maintenance free with brilliant light radiation
•DMX-control via everystandard DMX-controller
(1) Housing
(2)LEDS
(3) Floor-stand
(4)Menu-button
(5) Up-button
(6)Down-button
(7)Enter-button
(8) Power input
(9)DMX output
(lO)DMX-input
CAUTION
Be careful with youroperations.With a dangerous voltageyou can
Suffer a dangerous electric shockwhen touching wires
Thisdevice has left the factoryin perfect condition.In order to maintain this condition and to
ensure a safe operation,it is absolutelynecessaryfortheuser to follow the safetyinstructionsand
warning notes written in this user manual.

~.
Important:
Damages caused bythe disregard of this user manual are not subject towarranty.Thedealer
will not acceptliability foranyresultingdefects orproblems.
If the device has been exposed to temperaturechanges due to environmental changes,do not
switch it on immediately. The arising condensation could damage the device.Leave the device
switched off until it has reached room temperature.
Thisdevicefallsunder protection-class I. Thereforeit isessential that thedevice be earthed.
Theelectric connection must carryout byqualifiedperson.
Thedevice shall onlybe used with rate voltageand frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the powercord is never crimped or damaged by sharp edges.Ifthis would be the case,
replacement of the cable must bedonebyan authorized dealer.
Always disconnect from the mains,whenthedeviceis not inuse or beforecleaningit. Only
handlethe power cord bythe plug.Never pull out the plugbytugging the power cord.
During initial start-up some smoke or smell may arise.This is a normal process and does not
necessarily mean that the device is defective,it should decrease gradually.
Fixturescannot be installed on combustible substances,keep more than30cm distance with wall
forsmooth air flow,so there should be noshelter for fans and ventilation for heat radiation.
If the external flexible cable or cord of thisluminaire is damaged, it shall beexclusively replaced
bythe manufactureror his serviceagent or a similar qualified person in order to avoid a hazard.
-. Never touch thedeviceduringoperation
Thehousingmayheat up
Never look directly into thelight source,
as sensitive personsmaysuffer an epileptic shock.
Please be aware that damages caused bymanual modifications tothe device are notsubject to
warranty. Keep awayfrom children and non-professionals.
Thisdevice is a lighting effectfor professional use on stages,in discotheques,theatres,etc.
Thisfixture is only allowed tobe operated with themax alternating current which stated in the
technicalspecificationsin the last page of thismanual,the device was designed for indoor use
only.

Lighting effects are not designed for permanent operation. Consistent operation breaks may
ensure that the device will serveyou for a long time without defects.Do not shake the device.
Avoid brute force when installing or operating the device.
The device shall only be used complete with its protective shield.
While choosing the installation-spot,please make sure that the device isnot exposed to extreme
heat,moisture or dust. The minimum distancebetween light-output from the projector and the
illuminatedsurface must be more than 0.1 meter.
Operate the device onlyafter having familiarized with its functions. Do not permit operation by
persons not qualified for operating the device.Most damages are the result of unprofessional
operation.
Please use the original packaging if the device is tobe transported.
For safetyreasons,please be aware that all modifications on thedevice are forbidden.
If this device will be operated in any way different to the one described in this manual,the
product may suffer damages and the guarantee becomes void. Furthermore,any other operation
maylead to short-circuit,burns,electric shock,lamp explosion,crash,etc.
CAlJTIO~
Please consider the GB7000.15 EN60598-2-17 and the other respectivenational noID1S during
theinstallation. The installation must only be carried out by aqualified person.
The applicable temperature for the lignting is between _25
0
C to 45
0
C. Do notuse the lighting
under or above the temperature.
The installation of the effect has to be built and constructed in a way that it can hold 10 times the
weight for 1 hour without anyharmingdeformation.
The installation must always be secured with a secondarysafetyattachment,e.g. an appropriate
safety rope.
The operator has to make sure the safety relating and machine technical installations are approved
byan expert beforetakingthe device into operation for the first time.
These installationshaveto be approved by a skilled person onceayear.

CAUTION
Before takinginto operation for the first time,
the installation has to be approved by an expert.
Cautions:
The effect should beinstalledoutsideareas where personsmay reach it,walk by or be seated.
CAUTION
When installing the device,make sure there isno highly
inflammable material within adistance ofmin. O,3m.
Overhead mounting requires extensive experience,including amongst others calculating working
loadlimits,installation material beingused, and periodic safety inspection of all installation
materialand the device. If youlack these qualifications,do not attempt the installationyourself.
Improper installation can result in bodilyinjury.
Beforemounting make sure that the installationarea can hold a minimum point load of 10 times
the device's weight.
Connect the fixture to themains with the power plug.
Screw the bolt ofthe clamp intothehold ofthebracket,and tighten the screw underneath.
Pull the safety-ropethrough theholes on the bracket of thebase and over the trussing system or a
safefixation spot. Insert the endin thecarabine and tighten the safety screw.

Connect the provided XLR c;able to the female 3-pin XLR output of your controller and the other
side to the male 3-pin XLR input of the LED lighting. You can chain multiple LED lighting
together through serial linking.The cable needed should be two core, screened cablewith XLR
input and output connectors. Please refer to thediagram below.
DMXoutput
3-Pin XLR Socket DMX Input
3-Pin XLR Socket
~
2 1: Ground
•i. 2: Signal (-)
3: Signal (+)
DMX-512connection with DMX terminator
For installationswhere the DMXcablehasto run a longdistance or isin an electricallynoisy
environment,such as in a discotheque,it is recommended touse aDMXterminator. This helpsin
preventing corruption of the digital control signal by electrical noise. The DMX terminator is
simplyan XLR plug with a 120 Q resistor connected between pins 2 and 3,which isthen plugged
into theoutput XLR socketof thelast fixturein the chain.Please see illustrationsbelow.
120 Q
~
PIN 3
PIN 2
Projector DMX starting address selection
All fixtures should begivenaDMX startingaddress when using a DMXsignal,sothat the
correct fixtureresponds tothe correct control signals. Thisdigital starting address isthe channel
number from which the fixturestarts to"listen"to the digital control information sent out from
the DMX controller. The allocation of thisstarting address is achieved by setting the correct
number on the displaylocatedon the base of the device.

You can set the same starting address for all fixtures or a group of fixtures,or make different
addressfor each fixture individually.
[fyou set the same address,all the units will start to "li.sten"to the same control signal from the
same channel number.In other words,changing the settings of one channel will affect all the
fixtures simultaneously.
If you set a different address,each unit will start to "listen"to the channel number you have set,
based on the quantityof control channels of the unit.That means changing the settings of one
channelwill affect onlythe selected fixture.
[n the case of the led lighting,which is 6 channelsfixture when you select the standard channel
mode,you should set the startingaddress of the first unit to 1,the second unit to 7 (6+ 1),the
third unit to 13(6+ 7),and so on.
The Control Board offersseveral features: youcansimply set thestartingaddress,switch on and off thelamp,
run thepre-programmed program or makea reset.
The main menu is accessed bypressing the Menu-button until thedisplaystarts flashing.Browse through the
menu bypressingtheUp-button or Down-button.Press the Enter-button in order to select thedesired menu.
You can change the selection bypressingthe Up-button or Down-button. Confirm every selection by pressing
the Enter-button.You can leaveeverymodebypressing the Menu-button.The functions provided are
described in thefollowingsections.
Locked keys as default setting when starting up, press Meun key for 3 seconds to unlock.
The displaywill be locked automaticallywithout anyoperations in 15 seconds.

VALU
liJIII-xxx
(AXXX) DMX address setting
SLAV ONlI_(SLAV) Slave setting
ADDR
II/OFF C,hange DMX address via
RDMX external controller
Automatic Run III Stand
ALON (AU-A)
RUN AUTO Alone
0MODE MAST (AU-M) Automatic Run as Master
1~'I\j(DXXX) Display the DMX
512 value
VALU D-XX of each channel
DISP FLIP ON/III Reverse display
DON II/oFF Shut off LED display
LOCK Ill/OFF Key lock
,w ,r
iiiZ ik1~iiZ4i
FAIL OFFII.II/AUTO No DMX Status
REST Reset
1
SET DFSE
ONIIII
Restore factory settings
PO'vver on to preservethe
POHOMANL data
VER V-l.O~ V-9.9Software version
<COOL II XXX (000-255)
WARM XXX
(000-255)
TEMP I XXX (000-255)
2 MANL
I XXX (000-255)
Manual adjust intensity
STRB
DIMM 14 XXX (000-255)
ZOOM> I XXX (000-255)
LIFE OOOO~9999(hours) Fixture running time
3
TIME Clear fixture time *code is
CLFE "838"
STEP S-Ol ~.~
Steps of Program Run
REC. RE.XX Auto Save Scene
COOL I XXX (000-255)
WARM XXX (000-255)
TEMP XXX
(000-255)
4EDIT ~XXX
(000-255)
Edit the internal scenes
SCOl STRB
~SC48 DIMM
I XXX (000-255)
ZOOM I XXX (000-255)
TIME LXXX(OO 1 ~999) Time for each scene
CEDT /lli\1ili SJEdit program via controller
,,,,,,,,m,,

lEd 11:1
I. Press [MODEIESC] to enterthemain menu "MODE " (displayflashing)
2.Press [ENTER] and select "ADDR","RUN" or "DISP" bypressing [UP] or [DOWN]button.
3.Press[ENTER] for selecting the desired sub menu.
With this function, you can adjust the desired DMX-addressvia the Control Board.
l. Select "VALU" by pressing[UP] or [DOWN] button.
2. Press[ENTER], adjust theDMX address bypressing[UP] or [DOWN]button.
3.Press [ENTER] to confirm or-pressing [MODE/ESC] toreturn to main menu.
l
ei ell I
_/1 I II_ _ Slave setting
With this function, you can define the device as slave.
l. Select "SLAV" bypressing[UP] or [DOWN]button.
2.Press [E~TER], the display shows "ON" or"OFF"_
3. Press[UP)toselect "0"ifyou wish to enable this functionor press [DOWN] to select "OFF" if you
don't.
4.Press [ENTER] to confirm orpress [MODEIESC] to return tomain menu.