OYPLA Home 3924 User manual

User Manual
USER MANUAL Model No: 3924
Brass Mother & Child Lamp

•The product should only be connected to a 240V AC, 50Hz electrical outlet.
•This product is for indoor use only.
•Inspect the mains lead regularly. Never use the product if the mains lead or
plug has been damaged in any way.
•The shade and lamp become very hot when in use. Switch off and allow 10
minutes to cool before replacing the bulb, adjusting or cleaning.
•This product contains glass parts –be careful during handling and maintenance
to avoid breakage.
•Always use the correct wattage and shape light bulbs according to the product
label. Do not exceed the maximum wattages stated or this will overheat the
product and may cause damage.
•Ensure the lamp is placed on a stable, solid surface.
•This lamp contains heavy parts and care must be taken when moving or
handling this product.
•This product is intended for indoor use only.
•This product contains small parts that could be a choking hazard if swallowed.
Keep these items away from children.
•Make sure all fastenings are tightly in place and that everything is in order
before using the product. An adult should check this periodically.
•This product is not a toy, and is only to be used for its designated purpose.
•Do not carry out alterations or modifications to this product.
•Clean only with a dry cloth. Do not use strong industrial cleaning substances.
•Only use this product on stable, level and dry ground.
•This product is for domestic use only.
•If the product is damaged or has any defects, please contact
[e-mail].
Safety Instructions
Notice: Ensure you read and fully understand instructions before use
While every attempt is made to ensure the highest degree of protection in all equipment, we cannot
guarantee freedom from injury. The user assumes all risk of injury due to use. All merchandise is sold
on this condition, which no representative of the company can waive or change.
USER MANUAL Model No: 3924

Assembly Instructions
Parts List:
If you are missing any of the below parts please contact
[e-mail]
Please be aware that you will be referring to this parts list throughout the assembly
process.
4. Fit the washers and nuts to the lower
threaded sections of the stems and
tighten with the spanner provided.
Please see the image on the right,
marked as image 4.
3.Slide both stems into the base as
shown in the image on the right. Please
see the image on the right, marked as
image 3.
2. Fit the washer over the lower
sections of both stems. Please see the
image on the right, marked as image 2.
1. Screw the support stems into the
dimmer switch box. Take care not to
twist the cable in the stem. (This is
located in the middle of the product).
Please see the image on the right,
marked as image 1.
5. Fit the curved arms into the positions
shown below the bowl. Please see the
image on the right, marked as image 5.
USER MANUAL Model No: 3924

USER MANUAL Model No:
USER MANUAL Model No: 3924
Please retain a copy of all instructions for future
consultation.
Imported into the EU by Oypla.com LLP, Uxbridge, UB8 2FX
6. Take care not to trap the internal or
damage the internal cables. Please see the
image on the right, marked as image 6.
7. Secure the bowl with grub screws. Please
see the image on the right, marked as image
7.
8. Install the bulb into the top bowl by
springing it into place between the lamp
holder contents. Fit the safety glass shield
over the bulb and secure with two retainers.
Please see the image on the right, marked as
image 8.
Environmental Protection
Products bearing the symbol shown above means that used electrical and electronic equipment (WEEE) should not be mixed with general
household waste. For proper treatment, recovery and recycling, please take this product(s) to designated collection points where it will be
accepted free of charge. Disposing of this product correctly will help save valuable resources and prevent any potential negative effects
on human health and the environment, which could otherwise arise from inappropriate waste handling. Please contact your local
authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, in
accordance with your national legislation.
9. Install the bulb into the adjustable lamp
head and fit the glass safety shield. Fit the
adjustable handle into position on the lamp
head. Please see the image on the right,
marked as image 8.