OYPLA Home 4750 User manual

Page 1
Manual Version: V1.0
Model Code: 4750
Oypla.com LLP / www.oypla.com
User Manual
Model Code:
4750
Floor Standing
Lamp
Contents
1 Front Cover
2 Safety
Instructions
3 Assembly
Instructions
4 Back Cover

Page 2
Manual Version: V1.0
Model Code: 4750
Oypla.com LLP / www.oypla.com
Safety Instructions
Notice: Ensure you read and fully understand instructions before use
While every attempt is made to ensure the highest degree of protection in all equipment, we cannot
guarantee freedom from injury. The user assumes all risk of injury due to use. All merchandise is sold
on this condition, which no representative of the company can waive or change.
-This product is not a toy, and is only to be used for its designated purpose.
-Never carry out alterations or modifications to this product.
-This product is intended for indoor use only.
-Ensure the power supply to the socket into which the appliance is plugged, is in
accordance with the rating label on the appliance and that the socket is earthed.
-Do not use this product if the power cable is damaged. Return the product.
-To protect against electrical shock, do not immerse the cord, plug or any part of this
appliance in water or any other liquid.
-Do not leave the product on for extended periods of time as this will cause the bulb to
become hot and may decrease the overall lifespan of the bulb.
-Clean only with a damp cloth. Do not use strong industrial cleaning substances or
abrasive materials as these will damage the product. Make sure the product is
switched off and has been unplugged from the socket before you clean the product.
-If the product is damaged or has any defects, please contact cservic[email protected]
-Allow a minimum of 10 minutes to cool before replacing, adjusting or cleaning the
product.
-Do not look directly at the light.
-Keep lamp away from materials that may burn.
-Ensure the product is switched off at the rocker switch before installing.
-Check that the product is in good condition and has no defects before installing.
Contents
1 Front Cover
2 Safety
Instructions
3 Assembly
Instructions
4 Back Cover

Page 3
Manual Version: V1.0
Model Code: 4750
Oypla.com LLP / www.oypla.com
Contents
1 Front Cover
2 Safety
Instructions
3 Assembly
Instructions
4 Back Cover
Assembly Instructions
Technical Information
-Voltage: 220-240V/50~60Hz
-Foot pedal on/off switch
-Fabric & Metal
-Bulb base: E26
-Wattage: 60W
1) Screw the lampshade holder
onto the top of one of the poles.
2,3,4) Screw the poles together.
5) Connect the rod with the foot
switch to the lamp base.
6) Insert the two rollers into the
lampshade in the same
direction, and stick them on the
velcro, making them completely
coincident.
7) Connect the velcro to secure
the lampshade.
8) Attach the lampshade.
9) Screw on the holder to secure
the lampshade.
Parts List
-Body/Neck (4 poles including
plug/pedal switch)
-Upper lampshade roller
-Lower lampshade roller
-Light Bulb
-Base
-Lampshade

Page 4
Manual Version: V1.0
Model Code: 4750
Oypla.com LLP / www.oypla.com
Environmental Protection
Products bearing the symbol shown below means that used electrical and electronic equipment (WEEE)
should not be mixed with general household waste. For proper treatment, recovery and recycling, please take
this product(s) to designated collection points where it will be accepted free of charge. Disposing of this
product correctly will help save valuable resources and prevent any potential negative effects on human
health and the environment, which could otherwise arise from inappropriate waste handling. Please contact
your local authority for further details of your nearest designated collection point. Penalties may be applicable
for incorrect disposal of this waste, in accordance with your national legislation.
Imported by Oypla.com LLP, Uxbridge, UB8 2FX
Contents
1 Front Cover
2 Safety
Instructions
3 Assembly
Instructions
4 Back Cover