Oz Audio V10.3-2 User manual

1181 South Rogers Circle, Suite 18
Boca Raton, Florida 33487
e-mail [email protected]
www.jti-innovation.com
OZ VECTOR3® SUBWOOFER
01/05

Congratulations on your purchase of an Oz Audio Vector 3 Series subwoofer. The
Vector 3 subwoofers represent Oz Audio’s design approach to producing a bass pound-
ing and cost effective low frequency driver. Only the best materials and production tech-
niques were used to create an exceptional line of subwoofers. We hope you will enjoy
your Vector 3 subwoofer for many years to come.
Features:
• Custom designed, illuminated Oz dustcap
• Industrial finish, Oz powder coated basket
• 2-inch, dual 2 or 4-ohm coils on an aluminum former w/ reinforced neck joint
• Custom low distortion linear flux design with back plate ventilation
• Underlap™ cone attachment
• Custom injected-molded, brushed aluminum poly-mica cone
• Vapor deposition technology
• U-Turn Hyper-Surround™ for maximum linear excursion
• Poly-cotton blended flat progressive-roll spider with woven flat tinsel leads
• Precision machined and matched motor assembly
• Black e-coated magnetic plates provide superior voice coil cooling
• Nickel plated terminals
• 50 oz. high intensity grade ferrite magnet
• Custom embossed, protective magnet boot
The Vector 3 subwoofers offer the most value for the most discriminating listener. They
are designed to perform well in sealed, vented, or bandpass enclosures.
For optimum performance, make sure to have your authorized Oz Audio dealer design
and build your subwoofer system. They are equipped and trained to deliver the best sys-
tem design and installation.
1.

Model V10.3-2 V10.3-4 V12.3-2 V12.3-4
Fs (Hz) 38.81 39.73 36.71 37.48
Qts .65 .76 .68 .8
Vas (Liters) 17.25 17.25 40.99 40.99
Re (Ω)
(parallel) 1 1.85 1 1.85
Xmax (mm) 10 10 10 10
Sens (dB
1W/1M) 85 84 87 87
Rms/Peak
(Watts) 350/700 350/700 350/700 350/700
Mounting
Depth 4 7/8” 4 7/8” 5 1/2” 5 1/2”
Mounting
Diameter 9 1/8 ” 9 1/8 ” 11 1/8” 11 1/8”
Calculating Enclosure Volume
Specifications
2 3
Enclosure Recommendations
Multiplying all three internal dimensions in inches and then dividing the product by 1728
will produce the enclosure volume in cubic feet.
(H x W x D) / 1728 = Enclosure Volume ft.³.
Enclosures should be constructed with  inch MDF to prevent flexing of the enclosure
walls. When assembling the enclosure all panels should be first glued, and then fas-
tened together with either a brad nailer or screws in pre-drilled holes. After the enclo-
sure has been assembled all seams should be sealed with silicone.
Enclosure recommendations are internal volumes. Brace displacement, and port dis-
placement must be added to the volumes listed above.
NOTE: When constructing a vented enclosure, equalization is not recommended below
the enclosure tuning frequency (Fb). Also, the end of port should be no closer than it’s
own diameter to the wall opposite the opening.
Sealed V10.3-2 V10.3-4 V12.3-2 V12.3-4
Box Volume .8 ft.³ .8 ft.³ 1.25 ft.³ 1.25 ft.³
F3 48 Hz 45 Hz 46 Hz 44 Hz
Vented V10.3-2 V10.3-4 V12.3-2 V12.3-4
Box Volume 1.25 ft.³ 1.25 ft.³ 1.5 ft.³ 1.5 ft.³
F3 29 Hz 30 Hz 33 Hz 33 Hz
Fb 38 Hz 38 Hz 38Hz 38 Hz
Port Dia. 3” 3” 4” 4”
Port Length 8.5” 8.5” 12.75” 12.75”
D
H
W
Oz Dustcap LED Lighting
The Vector 3 subwoofers’ dustcap can be illuminated with a blue Oz logo. To activate
the LED lighting, connect the terminals that are above the LED designation on the mag-
net boot. The terminals are marked as + and –. Connect the – terminal to ground and
connect the + terminal to a positive 12-volt source that deactivates when the ignition is
turned off. Possible sources for a12-volt signal would be an ignition wire at the ignition
switch, the amplifier activation output from the radio, or a switch installed to activate the
lighting.

4 5
To locate the nearest Oz Audio® dealer, please call [phone] between 9:00am and
6:00pm EST. Monday thru Friday, or email us at [email protected], or write to JTI,
1181 South Rogers Circle, Suite 18, Boca Raton, FL 33487.
Due to ongoing product development, all specifications are subject to change without
notice. For detailed specifications on all Oz Audio speakers, please visit our website
(www.ozaudio.com) or consult with your authorized Oz Audio retailer.
CAUTION
This high-performance subwoofer is capable of producing sound pressure levels that
can cause hearing impairment or permanent loss. Please avoid prolonged exposure to
sound pressure levels in excess of 100dB to prevent such damage. Oz Audio assumes no
liability for bodily injury or property damage caused by the misuse of this product.