OzSpy GPT4G005COV User manual

GPT4G005COV Tracker User Manual v2020 1 | P a g e
COVERT WATERPROOF MAGNETIC GPS TRACKER
Instruction Manual v2020
SKU: GPT4G005COV

GPT4G005COV Tracker User Manual v2020 2 | P a g e
IMPORTANT SIM CARD AND BATTERY INFORMATION
PLEASE READ BEFORE USE!!
•CHARGE BATTERY FOR 24 HOURS BEFORE FIRST USE EVEN IF HARD WIRING TO THE
VEHICLE BATTERY BY CONNECTING TO A POWER POINT USING A USB ADAPTER
•PURCHASE A MOBILE PHONE 4G SIM CARD
•ACTIVATE THE SIM CARD AND APPLY CREDIT AS PER THE SUPPLIERS INSTRUCTIONS
•TEST THE SIM IN A MOBILE PHONE TO CONFIRM THE FOLLOWING:
1. SIM CARD CAN SEND & RECEIVE CALLS & TEXT MESSAGES (SMS)
2. SIM CARD SUPPORTS DATA (INTERNET USAGE APPROX 10-30MB/MTH)
3. MESSAGE BANK/VOICE MAIL AND VOICE TO TEXT SERVICES ARE REMOVED
4. SIM PIN CODES ARE REMOVED
NOTE: To add or remove services please contact your SIM Service Provider.
For further information visit: https://www.ozspysupport.com
Thank you for purchasing an OzSpy Covert 4G Waterproof Magnetic Long-Life GPS Tracker
with free Live Tracking. This GPS Tracker suits personal or vehicle tracking with fleet
management and includes many features, such as:
•Extra-large battery (6000mAH). Its standby time can reach 3 weeks depending on the
working mode setup.
•Water-Proof case with a strong magnet. A strap maybe added for extra peace of
mind.
•Check the current location anytime by iPhone or Android App, Website or SMS
•Built in GPS and GSM module
•LBS locate when there is no GPS signal, (mobile phone base station; LBS CELL ID
locating precision is about 50-500m in a city; GPS is 10m)
•Fleet Management (Contact your OzSpy Representative for initial account setup)

GPT4G005COV Tracker User Manual v2020 3 | P a g e
INITIAL SETUP
Power ON / OFF:
When the power is OFF, press the “ON/OFF” button until the green LED is ON, then release
the button. The tracker is now powered ON. Green and Red LED’s will flash as per details
below.
Green LED Flash once
Working well
Green LED Flash twice
GSM working well and GPS signal weak
Green LED Flash three times
GSM and GPS working well but battery is low
Green LED Flash four times
GSM working well, battery low & no GPS signal
Green LED ON continuously
GSM Searching for a network
Green LED OFF continuously
Power is off
Red GSM LED Flash once
Upload location to server OK
Red GSM LED Flash twice
Upload location to server Fail
When the power is ON, press the “ON/OFF” button till the Green LED Flash fast, and then
release the button and press the ON/OFF button 3 times, the tracker will turn off.
If the battery is flat, recharge the tracker and the Tracker will power on automatically.

GPT4G005COV Tracker User Manual v2020 4 | P a g e
Installing the SIM card:
Note: Before installing or removing the SIM card, please power off the tracker.
Remove the rubber seal on the side of the tracker to access
the SIM card tray. Press the yellow button with a tool to eject
the tray. Place the SIM card in the tray making sure SIM card
metal contact pins are facing up. Insert tray back into the
Tracker and replace the rubber seal to cover the SIM card
socket.
Charging the Tracker:
We recommend using the 5V DC OEM charger only
to recharge the tracker. Using an incorrect power
supply may cause damage to the tracker and void
your warranty.
Insert the USB connection into a power or car
adapter or PC USB port. If the LED on the adapter is
RED, it means it is recharging, if the LED on the
adapter is GREEN, it means the recharging is
finished. This will take about 8-10 hours (with
exception to the first charge of 24 hours).
The tracker can also be connected to a car battery
using an external power adapter (9-30V input 5V
output). Insert the external power adapter output
wire to the tracker charging socket and connect the
external power adapter input to the car battery (9-
30V). Once the battery is fully charged, the tracker
will stop charging and use the external power
adapter for continued operation, the built-in
battery will only be used for backup.
Note: When the battery voltage in the tracker is low, the tracker GREEN LED will flash 3 or 4 times
and send battery low alarm information to the authorized phone number.

GPT4G005COV Tracker User Manual v2020 5 | P a g e
Set APN & GPRS Username and Password:
If the APN & GPRS username and password are not automatically set correctly, the tracker
cannot upload its location to the server (Red LED flashes twice).
To check the automated setup, send an SMS (without the
inverted commas) “CHECK*12345678” to trackers assigned
phone number. “CHECK” is the fixed command, “12345678” is
the default tracker password.
Due to the SMS length the response is usually split between 2
messages and the APN shown in the example image is
“internet”.
To change the APN, send an SMS “APN*12345678*apnname” to
the tracker, in which, “APN” is the fixed command, “12345678”
is the password and “apnname” is the APN name supplied by
your telephone service provider. Once the changes have been
successfully been made, the tracker will respond with an SMS
“APN: apnname Battery: 00%”.
To confirm the correct APN (Access Point Name) for your account please contact your SIM
Provider. The most common are listed below.
*NOTE: APN details are case sensitive.
SERVICE PROVIDER
APN
Telstra
telstra.wap
Telstra
telstra.internet
Telstra/Boost
telstra.iph
Optus
internet
Optus/iiNet/TPG/ Dodo/amaysim
yesinternet
Vodafone/Kogan
live.vodafone.com
Vodafone
vfinternet.au
Aldi/Belong/Woolworths
mdata.net.au
Crazy John's Vodafone
purtona.net
Virgin
VirginInternet

GPT4G005COV Tracker User Manual v2020 6 | P a g e
GPS TRACKING PLATFORMS
The default username is the last 7 digits of the tracker ID number, refer to label on the box
and/or tracker. The password is the same as the username.
Visit the website http://www.9992gps.com/ and logon using the unique username and
password. A user can then check the real time location, playback tracking history (6-12
months), or set various alarms such as overspeed alarm, geo-fence etc.
An App can be installed on an Android or iOS Mobile Phone or Tablet. Scan the relevant QR
code or click the following links to download the App.
iPhone App Download Android App Download
GENERAL OPERATION
Phone Tracker Locate Command:
Call the tracker SIM card number, after 3 rings, the tracker will hang up the call and send
back an SMS with the current location by either a text
location description or a Google map link.
If the tracker has authorized phone numbers set, only an
authorized number can trigger the tracker locate command. If
an unauthorized number calls the tracker, the call will be
immediately disconnected, and no response will be sent. If
the tracker cannot get the text location description, the tracker will send a Google map link
for the current location. If there is no GPS signal the tracker will locate by LBS (Cell ID GSM
network base station) and reply the LBS location with the Google map link.

GPT4G005COV Tracker User Manual v2020 7 | P a g e
SOS Emergency Help:
In the normal operating mode press the button ON/OFF on the tracker and don’t release
(Press button over 6 seconds). The GREED LED will flash quickly, then the LED will turn OFF.
Release the button and the tracker will send SOS help information to all 3 preset phone
numbers. It will then call the authorized numbers starting from A. If there is no answer, then
it will try B and then C and then stop calling.
The SOS SMS information sample is as follow:
HELP!
https://maps.google.com/maps?q=22.67680N,114.15188E
Battery:91%
Note: If no authorized numbers are set, the SOS information cannot be sent.
Mobile Phone SMS Commands:
Send SMS/Text message to Tracker SIM service number from a mobile phone. The default
Tracker password is 12345678. If the password is incorrect the tracker will respond, “Wrong
Password”. If the command is incorrect the tracker will respond, “Bad Command”.
1. Add authorized phone number – ADDPHONE*12345678*A*xxxxxxxxxx
“ADDPHONE” is the fixed command; “12345678” is the default tracker password; “A” is
authorized number location (every tracker has 3
authorized phone number locations; A, B and C);
“xxxxxxxxxx” is the mobile phone number you want to
set. If the add operation is successful, the tracker will
respond, “Add Preset Phone OK”
2. Check Authorized Phone Number - CHECKPHONE*12345678
“CHECKPHONE” is the fixed command; “12345678” is password. The tracker will send back the
information “Authorized Phone A: 0412345678；B: 0412987654；C：0459654123. (The phone
numbers are examples.)
3. Delete Authorized Phone Number - DELETEPHONE*12345678*A
“DELETEPHONE” is the fixed command; “12345678” is the password; “A” is authorized phone
number location, there are 3 locations “A” and “B” and “C”; if the delete operation is successful,
the tracker will send back the information, “Delete Authorized Phone OK”.

GPT4G005COV Tracker User Manual v2020 8 | P a g e
4. Check Tracker Password - CHECKPASSWORD
“CHECKPASSWORD” is the command, if the operation is successful, the tracker will send back
the information “Password：888888”; “888888” is an example. The tracker password is used to
protect the tracker, so that it can only be operated by the owner. SMS commands use the tracker
password. The default tracker password is 12345678. This password is different from the
tracking platform login password.
Note: Only The authorized phone can check or change the password
5. Change Tracker Password - CHANGEPASSWORD*12345678*888888
“CHANGEPASSWORD” is the command; “12345678” is the old password; “888888” is new
password. If the operation is successful, the tracker will send the information “New Password：
888888” to every preset phone number.
Note: Only The authorized phone can check or change the password
6. Trigger Location Response – LOCATE*12345678
“LOCATE” is the fixed command; “12345678” is password. If the tracker is in a place where there
is no GPS signal, such as underground park or indoor room, the tracker will reply “No GPS
signal” and give the Cell ID Location. Note: The LBS location precision is not as accurate. City
locations may range from 30-50m, with rural areas over 300m depending on the GSM base
station density. If the LBS cannot locate either, the tracker will reply “No GPS signal and Cell ID
Location is unavailable, pls try again later”.
7. Trigger Google Map Link Location – URL*12345678
“URL” is the fixed command; “12345678” is password.
Tracker will respond with a Google Map Link. Refer to example
image.
8. Reset/Reboot Tracker - RESET*12345678
“RESET” is the command, “12345678” is password. The tracker will send back information
“Reset Tracker and cancel all alarm setting”, then the tracker will power off and then power on
automatically. This command will not cancel the user settings.
9. Restore Factory Default Configuration - FACTORY*12345678
“FACTORY” is the fixed command, “12345678” is password. The tracker will send back

GPT4G005COV Tracker User Manual v2020 9 | P a g e
information “Set factory setting OK”. This command will cancel all alarm settings, delete the
authorized phone numbers, delete the APN and GPRS username and password, reset the
tracker password to 12345678, reset the IP address, reset the system working mode and the
interval time, etc. If the tracker password is forgotten, use the authorized mobile phone to
check or change the password. If no authorized phone is added, then user cannot reset the
tracker to factory mode.
10. Check Tracker Settings - CHECK*12345678
“CHECK” is the fixed command; “12345678” is password. The tracker will send back information
including software version, ID S/N number, IP address, authorized phone number, GPS and GSM
signal etc. This command is used to check the Tracker configuration.
Example SMS response:
800G(3G) V Dec 06 2017, CC830, 8002018xxxxxxxx, d3.igps.info, 8011, 30, MODE 1, NO PHONE,
GPS OK, 0, ShockControlGPS, -99dBm, ShockControlGPRS, telstra.internet, 50501, Battery:100%
800G(3G) V Dec 06 2017 Product model & Software version
CC830 Protocol (CC800/CC828/CC830/CC630 etc.)
8002018xxxxxxxx Tracker ID number
d3.igps.info, 8011 Server/IP and Port Number
30 Upload Time Interval
MODE:1 System Working Mode
NO PHONE No Authorized Phone (if authorized phone added, will list
phone numbers store for A, B & C)
GPS OK GPS signal OK or No GPS
0Report Mode
ShockControlGPS
-95dBm GSM signal
ShockControlGPRS
telstra.internet Current APN
50501 GSM Base Station
Battery:100% Battery Power
11. Auto SMS Cycle Tracking - LOCATE*12345678*MMM or URL*12345678*MMM
“LOCATE” or “URL” is the command, “12345678” is the password, “MMM” is the locating time
interval in minutes. If the operation is successful, the tracker will reply “SMS Cycle Tracking,
Interval is MMM minutes”, and then the tracker will locate every MMM minutes, and send
location to the user by SMS. To cancel the command, send SMS: 000*12345678.
Note: This command will increase battery usage and additional SMS charges may apply.

GPT4G005COV Tracker User Manual v2020 10 | P a g e
12. Auto SMS Real Time Tracking for 2 Hours - TRACKING*12345678
“TRACKING” is the command; “12345678” is password. If the operation is successful, the tracker
will reply “SMS Real Time Tracking 2 Hours”. The tracker will then locate every 2 minutes and
send location Google map link to user by SMS. This command will stop automatically 2 hours
later. To stop the command at any time, send SMS: 000*12345678.
Note: This command will increase battery usage and additional SMS charges may apply.
13. Set Upload Interval Time - INTERVAL*12345678*T
“INTERVAL” is the command, “12345678” is the password, “T” is the interval time from 30 to 999
seconds. The tracker will send back information “Set Interval time T OK”. 300 seconds is the
default interval time. Setting a longer upload interval time can save the battery and GPRS data
cost, however, the total mileage data recorded on the GPS999.net platform will be less accurate
if the interval time is more than 300 seconds.
14. Set Sleep Time - SLEEPON*12345678*T1*T2*Timezone
“SLEEPON” is the command, “12345678” is password, “T1” is the local time to begin to sleep (24
hours), “T2” is the local time to wake up (24 hours), “Timezone” is the local time zone. The
tracker will send back information “Set sleep time (T1-T2), Timezone: Tz”. After receiving the
command, the tracker will begin to sleep from time T1, and wake up from time T2, if the T2 is
smaller than T1, it means the wake up time is the second day, after the tracker go to sleep, it
cannot be triggered by SMS or calling to locate, only after wake up the tracker can receive
command.
Examples: Set sleep from 10pm to 8am, time zone is +10 (AEST), the SMS will be
“SLEEPON*12345678*22*8*10”. To set sleep from 10pm to 8am, time zone -5 (New York), the
SMS will be “SLEEPON*12345678*22*8*-5”.
The sleep can be disabled by SMS “SLEEPOFF*12345678”, however if the tracker is in sleep
status, the tracker will disable the sleep time after it wakes up.
15. Enable/Disable Overspeed Alarm - OVERSPEEDALARMON*12345678*SSS
“OVERSPEEDALARMON” is the command, “12345678” is password, “SSS” is the setting alarm
speed, unit is km/hour. The tracker will send back the information “Set Overspeed Alarm On :SSS
km/h” . After enable overspeed alarm, the system will check the speed every 5 minutes. If the
speed is higher than the setting speed, the tracker will send alarm and location information by
SMS to the authorized phone number A (only send to A), The authorized phone will receive max
3 alarm SMS per hour, one hour later it will be active again.