OzSpy GPT002 User manual

GPT002
User Guide

Contents
1. Setting up Tracker for first time
2. Where to put tracker on vehicle
3. Setting up GPS perimeter
4. Authorising Tracker users
5. Monitoring mode
6. Moving Alert
7. Speeding Alert
8. Quick Commands
9. GPT002 Specifications
10. Troubleshooting

User Manual: Initial setup
Before using your GPS tracker ensure you have charged the Lithium battery!
1. Setting up your Tracker for the first time
Put the SIM card and battery in place.
1. Installation
Put your SIM card into the SIM card tray, then insert the supplied battery, ensure there are
not any plastic seals on battery terminals!
2. Initialization
Each GPS Tracker needs to be initialized before use.
To Initialize you need to send begin123456 as a text
message to the tracker
Your tracker will reply: Begin ok!
To receive the trackers location, send tracker123456
as a text message to the tracker.
Your tracker will reply: Tracker ok!

Where to put your GPS tracker?
You must be careful with where you want to place this device. Today’s GPS
tracking devices do not require the use of a large external antenna that hangs
outside of the vehicle in order to get the GPS signal. Instead, today’s GPS devices
only require the use of a safe location on the vehicle.
Make sure you test your tracker before deciding the location of which you want it hidden.

5. Setting up fence breach
Geo-fence will help you to restrict the target within a certain set area. When the target
breaches the restricted area, you’ll get a message alerting you.
Note: You need to let the tracker stay still for 10 minutes before you send the command to
it.
The command is stockade123456 (latitude)1e, (longitude)1n; (latitude)2e, (longitude)2n
Example (stockade123456 153.161641e,-27.654471n; 153.173954e,-27.662054n)
The following picture will show you how it works; the restricted area is defined by
the two coordinates you set.
As soon as your geographic square is breached you will be alerted!
If the Area is 10km x 10km or smaller the tracker will not trigger until target is
1.5km outside the area
Authorization of Tracker
There are only 5 numbers maximum able to be authorized to use the tracker.
To authorise a mobile phone number Send: admin123456 (admin phone number)
Example: admin123456 0405678432
If number is successfully authorized the tracker will reply Admin OK!

Monitoring Mode (Voice Surveillance)
Send (monitor123456) the response from the tracker is “monitor ok”
In this mode, the user can dial up the unit to hear the voice around the tracker.
There are two Modes you can switch between “track” and “monitor”
SMS monitor123456 to the unit and it will reply “monitor ok!”
SMS tracker123456 to the unit and it will reply “tracker ok!”
Movement Alert
This function is useful for the owner to receive a notification/alarm when the tracker begins
to move:
SMS shake123456 3 to the unit to set the movement alert.
Then the unit will reply “Shake ok!” In case of such a movement, it will send SMS the
latitude and location.
To cancel the alert, SMS shake123456 0 to deactivate the movement alert
Speeding Alert
This function allows the phone user to set an alert that alerts you if the driver has exceeded
a certain speed limit.
To set up, SMS speed123456 (three digit speed limit) to the unit
Example: speed123456 080 for 80km/h
The tracker will reply “speed ok!”
When the target exceeds 80 km/h or more, the unit will SMS an alert.
To cancel the alert SMS nospeed123456 to deactivate
Note: It is recommended that the speed alarm is set at no less than 50km/h

Quick SMS Commands
Function
Command
Reply
Start Tracker
Begin123456
beginOK!
Authorise Number
Admin123456 04********
adminOK!
Auto Track - Low
t030s005n123456
Notn OK!
Auto Track - Medium
t005m026n123456
Notn OK!
Auto Track - High
t001h010n123456
Notn OK!
Cancel Auto Track
Notn123456
Nostockade ok!
Voice Monitoring
Monitor123456
Monitor Ok !
Movement Alert
Shake123456 3
Shake Ok!
Cancel Movement Alert
Shake123456 0
Noshake ok!
Tracking Mode
Tracker123456
TrackerOK!
Check IMEI Code
Imei123456
IMEIok!
Low battery Alert
Lowbattery123456
Battery Status
Change Time Zone
Time zone123456 10
TimezoneOK!
Send Google Link
Smslink123456
SmslinkOK!
Send Lat/Long
Smstext123456
Smstextok!
Quick Website
In order to use OzSpy’s Live Tracking function, the user needs to set IP, Port and APN details
either via a cell phone or go to the following link to log into GPS Live tracking site
http://118.127.25.31:8080

GPT002 Specifications
Name
Parameter
Model
TK102-2
Size
64(L)x46(W)x17(H) mm
Weight
50g
Communication net work
GSM/GPRS
Frequency
850/900/1800/1900Mhz
Sensitivity
-102dBm or less
GPS chip
SIRF3 chip
GPS sensitivity
-159dBm
Accuracy
5 meters
Cold/hot start
35/2 seconds
External power
DC5V input
Battery
3.7V 860mAh lithium battery
Battery standby time
About 100 hours
Operation Temp
-10°C to +65°C
Storage Temp
-20°C to +70°C
Relative humidity
5% to 95 %, non-condensing
Troubleshooting
Question
Answer
My GPS tracker will not turn on?
Ensure the plastic terminal seals have been
removed from lithium battery
My GPS tracker is not responding?
Ensure sim card has been activated and
device has phone reception
My GPS tracker just has a constant flashing
light?
This means it cannot detect sim card