OzSpy GPT3G003 User manual

Personal GPS/GSM Personal
Tracking Device

INDEX
Usage
Packing list
Before using
Add/Delete/Check Preset Phone Number
Change / Check Password
Set language
Set SMS locate mode after calling
Send a SMS trigger SMS locate
Set website map link locate mode after calling
Send a SMS trigger website map link locate
Set move alarm
Over Area Alarm
Over Speed Alarm
Real Tracking Mode
Cancel All Alarm Setting
Low Battery Alarm
Monitor & Listen Sound around tracker
Call and talk to preset phone
Set Power Saving mode (Set GPS On Off Interval)
“SOS”
Installation Guide
Notes
Trouble Shooting
Instruction List

Usage
Our free latitude and longitude located website:
http://www.followmegps.com
Our free link located map website:
http://www.followmegps.mobi
Packing list
GPS tracker, car charger, USB charging cable, manual.
Before Use
USB Charging Wire Car Adaptor
Purchase a GSM phone SIM card which has SMS service and incoming caller ID service, and then to
install to the tracker. All operation for this tracker is linked to the number, such as locating immediately,
add & delete preset numbers, change password, enable over speed alarm, enable move alarm etc.
Note: This tracker is compatible with 3G SIM cards however it only operates on a 2G band.
1. Power ON / OFF
When power is OFF, press the “ON/OFF” button untill the LED is ON, then release the button,
the tracker is powered ON, when the LED flash means the tracker is working well.
When the power is ON, press the “ON/OFF” button till the LED turn off, then release the button,
the tracker is powered OFF.
When power is OFF, recharge the tracker, the tracker will power on automatically.
When the battery voltage in the tracker is too low, the tracker will power off automatically
2. Install SIM card: Pull out the battery cover and remove the battery, you can see the SIM card
holder under the battery, move the metal cover to another side, you can lift one side of the metal
cover, put the SIM card into the holder (Metal pin face down), and make the cover fasten.
Note: Before installing or uninstalling the SIM card, please power off the tracker.
3. LED flash indicator
Green Power LED Flash once : working well
Green Power LED Flash twice : GSM working well and GPS signal weak

Green Power LED Flash three times : GSM and GPS working well but battery is low
Green Power LED Flash four times : GSM working well, battery low & no GPS signal
Green Power LED ON continuously : Searching network
Green Power LED OFF continuously : Power off
Blue GPS LED ON : GPS module is ON
Red GSM LED Flash fast : Incoming or making a call or receiving a SMS
4. Recharge the tracker
Warning: this tracker uses 5V DC voltage to recharge; higher voltage or AC voltage may
damage the tracker or even cause accidents.
Use the car adaptor to recharge the tracker: insert the USB cable into the tracker and car
adapter, If the LED on the adaptor is RED, it means it is recharging, if the LED on the
adaptor is GREEN, it means, it means the recharging is finished. This will take about 2-4 hours.
When recharging, It will take approx 3-4 hours to finish charging, the car adaptor LED will turn to
GREEN, when the battery is low, the LED will flash three times, and send the battery low
information to the first preset number. When the battery voltage is too low, the tracker will power
off automatically, but when you recharge the tracker, it will power on automatically.
5. Back to default settings
Pull out the battery cover and remove the battery, press the “ON/OFF” button and hold on, insert
the battery into the tracker, the tracker will power on, after the LED flash 10 times and the LED will
turn on continuously, release the button, the tracker will revert back to default settings, delete all
preset phone number and password, the password is changed to default: 123456.
6. ANTENNA
- TheAntenna of GSM and GPS are built in to the tracker.
Using Condition
The working temperature is -20 0C to 60 0C, over this range the specification of the tracker may not
function correctly, the storage temperature can reach to -40 0C to 80 0C.
Function Description
Add / Delete / Check preset number:
Preset Phone Number: user can set 3 preset phone number, this number is used as sending SOS help, low
battery alarm information and change/check tracker password and trigger the locating by

calling, only preset phone number can do these operation.
1. Add preset phone number by SMS
Send SMS“ADDPHONE*123456*A*number”(Not including the quotation marks “and ”,
Number means the telephone number you want preset, the following is same) to tracker is OK,
“ADDPHONE” is a command; “123456” is password; “A” is preset number location, every tracker
have is 3 preset phone number location, A , B and C, so you can preset 3 phone number, if the
add operation is success, the tracker will send back the information ”ADDPHONE OK”, if
the command or password is not right, the operation fault, the tracker will send back information
“ADDPHONE FAIL”.
2. Delete preset phone number by SMS
Send SMS “DELETEPHONE*123456*A” to the tracker, “DELETEPHONE” is a command;
“123456” is password; “A” is preset phone number location, there is 3 location “A” ，“B” and “C”;
if the delete operation is success, the tracker will send back the
information ”DELETEPHONE OK”, if the command or password is wrong, the operation fault, the
tracker will send back information “DELETEPHONE FAIL”.
3. Check preset phone number by SMS
Send SMS “CHECKPHONE*123456” to tracker, “CHECKPHONE” is a command; “123456” is
password; if the operation is success, the tracker will send back the information “CHECKPHONE
A: 13322990998；B：13322990033；C：13316868198”, the phone
number is just an example.
Change / Check Password
1. Change tracker password
Send SMS “CHANGEPASSWORD*123456*888888” to tracker, “CHANGEPASSWORD”
is a command; “123456” is old password; “888888” is new password; if the operation is
success, the tracker will send the information “New Password：888888” to every preset phone
number, if the operation fail, the tracker will send back information “CHANGEPASSWORD FAIL”.
Note: Only preset phone can change the password.
2. Check tracker password
Send SMS “CHECKPASSWORD” to the tracker, “CHECKPASSWORD” is a command, if the
operation is success, the tracker will send back the information “Password：888888”; “888888”is
an example.
Note: Only preset phone can check the password.

Set Language:
Send SMS “ENGLISH*123456” to the tracker, “ENGLISH” is a command, “123456” is password; if
the operation is successful, the tracker will send back the information “Set Language to
English” , If the command or password is not right, the operation is fault, the tracker will send
back information “Bad Command ”or “Wrong Password”. After setting the language to English, all
the SMS information is change to English, the default langue is English,
also you can set the langue to Chinese, replace the command “ENGLISH” to “设置中文”is OK.
Set SMS locate mode after calling:
1. Send SMS “SMSMODE*123456” to the tracker, “SMSMODE” is a command, “123456” is
password; if the operation is success, the tracker will send back the information “Set Report
Mode to SMS” , if the command or password is not right, the operation is fault, the tracker will
send back information “Bad Command ” or “Wrong Password”.
Please note that this SMS is just a mode setting command, it will not trigger the tracker locate
immediately, Call the tracker or send SMSLOCATE SMS can trigger locate immediately.
2. Under this report mode, using preset phone call the tracker, after ringing 3 times, the tracker
will hang up the call automatically and locate immediately, about 30 seconds, the tracker will
send back the SMS location information (latitude longitude speed battery time etc) of current
location to the caller. If the tracker has not preset number, any phone call can trigger the
tracker to locate immediately and send back location, if the tracker has preset number, then
only preset phone call can trigger the tracker to locate immediately.
3. Basic Location information including Latitude, Longitude, Speed, Direction, Date & Time, Battery
etc. the SMS information sample is as follow:
Latitude: 22.680206N Longitude:
114.146998E Speed (km/h):45.0 Direction
(Degrees):303.30 GMT:2008/04/25
08:29:06.000
Battery: 91%
The first line is the latitude of the tracker.
The second line is the longitude of the tracker.
The third line is the speed of the tracker (the speed maybe is not zero if the object is not moving
because of the GPS precision)

The fourth line is the direction of the tracker (It is the direction of the tracker moving to, from
the north it is 0, and the east is 90, and the south is 180, and the west is 270, full circle is 360, it is
clockwise, the direction maybe is not right if the object is not moving because of the GPS
precision).
The fifth line is the GMT time and date, (this time is the world standard Greenwich time, and
this time is the 0 degree longitude line time, your local time need add or minus a fixed number of
hours, for example China Beijing time is GMT add 8 hours, it means it is 8 hours earlier than GMT
).
The sixth line is the tracker battery capacity, if the battery is lower than 10%, tracker will send
battery low information to preset phone number.
4. If the tracker cannot receive the GPS signal, it cannot locate current location, then it will send the
last locating information to caller, and add a warning information “GPS signal weak, Last
located:” , the following information is the last locating information.
5. User visit a free website www.followmegps.com to input the latitude & longitude coordinates to
locate the tracker on the map; also user can use free Google Earth to locate the tracker.
Send a SMS trigger SMS locate
Also send a SMS “SMSLOCATE*123456” to the tracker, “SMSLOCATE” is a command,
“123456” is password; the tracker will locate immediately and send back the location information
(latitude longitude speed battery time etc) of current location to the caller. The SMS example is
same with above, if the command or password is not right, the operation is fault, the tracker will
send back information “Bad Command”or “Wrong Password.
Set website map link locate mode after calling:
1. Send SMS “LINKMODE*123456” to the tracker, “LINKMODE” is a command, “123456” is
password; if the operation is success, the tracker will send back the information “Set Report
Mode to Map Link” , if the command or password is not right, the operation is fault, the tracker will
send back information “Bad Command ” or “Wrong Password”.
Please note that this SMS is just a mode setting command, it will not trigger the tracker to locate
immediately. Call the tracker or send LINKLOCATE SMS which can trigger locate immediately.
2. Under this report mode, using preset phone call the tracker, after ringing 3 times, the tracker
will hang up the call automatically and locate immediately, after 30 seconds, the tracker will
send back the SMS location information (map website link) of the current

location to the caller. The user can use the mobile phone to click the website link to visit
internet, and the location will display on the map of your phone(the mobile phone SIM card needs
the GPRS function enabled). If the tracker has no preset number, any phone call can trigger the
tracker to locate immediately, if the tracker has a preset number, then only preset phone call can
trigger the tracker to locate immediately.
3. Basic Location information including Map Website Link, Battery etc. the
SMS information sample is as follow:
http://www.followmegps.mobi/map.aspx?lat=40.756441&lng=-73.986378&l=en (World
Goolge map)
Battery: 91%
The first line is the current location on the map website link, the other information is same as
above.
4. User use mobile phone, click on the link to visit the website, the location on map and
location description in text will display on your mobile phone. Also you can click + and –to enlarge
or reduce the map, the following is the example.
Send a SMS trigger website map link locate
Send SMS “LINKLOCATE*123456” to the tracker, “LINKLOCATE” is a command, “123456” is
password; the tracker will locate immediately and send back the location information (map website
internet link) of current location to the caller. use mobile phone to click the website link to visit the
internet, and the location will display on the map on your phone(the mobile phone SIM card needs
to have the GPRS function), if the command or password is not right, the operation is fault, the
tracker will send back information “Bad Command ”or “Wrong Password. Please note your
mobile phone must have a internet browser in order to go to the map link.

Set Object Move Alarm (Can be used as a car alarm):
Send SMS “SETMOVE*123456” to tracker, “SETMOVE” is a command, “123456” is
password, the tracker will send back the information “SETMOVE OK” or “SETMOVE FAIL” to indicate
the operation if it has success or failed。
After set the object move alarm, the system will monitor the object continuously, if the object
is moving, the tracker will send alarm and location information by SMS to who enable the alarm,
and every 5 minutes the tracker will send alarm information by SMS until the tracker stop
moving.
The object move alarm SMS is as follow: ObjectMove
Latitude:22.680206N
Longitude:114.146998E Speed(km/h):45.0
Direction(Degrees):303.30 GMT:2008/04/25
08:29:06.000
Battery:78%
Over Area Alarm:
Send “SETAREA*123456*A22.670000N114.140000E*B22.680000N114.150000E” SMS to
the tracker, “SETAREA” is a command, “123456” is password, “A22.670000N114.140000E” is the
longitude and latitude of the first point(Point A) location, “B22.680000N114.150000E” is the longitude
and latitude of the second point(Point B) location.
Note: the over area set needs 2 points, it is A and B, Point A must be on the bottom left of point B,
the format of latitude and longitude of every point is as follows: Latitude format is YY.YYYYYYN, it
has 8 digits, the last is N or S, means north latitude or south latitude, if the digit is not reach to 8
please add zero to 8 digits, Longitude format is XXX.XXXXXXE; it has 9 digits, the last is E or W,
means east longitude or west longitude, if the digit is not reach to 9

please add zero to 9 digits, if the command and password is right, the tracker will send back the
information “AREASET OK” or “AREASET FAIL” to indicate the operation is success or failed.
After set the over area alarm, the system will locate every 5 minutes and check the object is in the
preset area or not, if the object is go out the area, then the tracker will send SMS to the phone who
enable the alarm.
The over area alarm SMS information is as follow: Over
Area
Latitude:22.680206N
Longitude:114.146998E Speed(km/h):45.0
Direction(Degrees):303.30 GMT:2008/04/25
08:29:06.000
Battery:89%
Over SpeedAlarm:
Send SMS “SETSPEED*123456*040” to tracker, “SETSPEED” is a command, “123456” is
password, “040” is the preset report speed, the speed must be 3 digits , from 000 to 999, unit is
Km/hour, the tracker will send back the information “SETSPEED OK” or “SETSPEED FAIL”
to indicate the operation is success or failed。
After setting the over speed alarm, the system will locate every 5 minutes and check the speed
of the tracker is higher than the preset speed or not, if the speed is higher than the preset speed,
the tracker will send SMS to the phone who enable the alarm.
The over speed alarm SMS is as follow: Over
Speed
Latitude:22.680206N
Longitude:114.146998E Speed(km/h):45.0
Direction(Degrees):303.30 GMT:2008/04/25
08:29:06.000
Battery:78% Set
Real Tracking Mode:
Send SMS “SETTRACKING *123456*15M030T” to tracker, “SETTRACKING” is a
command, “123456” is password, “15” is locate interval time, “M” means the time unit is