PACOM PAC-171AV User manual

Please read this manual thoroughly before use, and keep it handy for future reference
PAC-171AV
User’s Manual
TFT-LCD MONITOR

IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these Instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug.
Apolarized plug has two blades with one wider than the other.
Agrounding type plug has two blades and a third grounding prong.
The wide blade or the third prong is provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at plugs,
convenience receptacles and the point where they exit from the apparatus.
11. Only use attachment/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer
or sold with the apparatus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus the
apparatus has been exposed to rain or moisture does not
operate normally or has been dropped.
- The apparatus shall not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases , shall be placed on the apparatus.
- Minimum distances (e.g. 10cm) around the apparatus for sufficient ventilation.
“WARNING - To reduce the risk of fire or electric shock, do not expose the
apparatus to rain or moisture.”
“The apparatus shall not be exposed to dripping or splashing and no objects filled
with liquids, such as vases, shall be placed on the apparatus.”
E
U
s
er manual
- 2 -

7. Water and Moisture : Do not use this monitor near water for
example, near a bathtub, wash bowl, kitchen sink or laundry tub, in
a wet basement or near a swimming pool and the like wet
basement or near a swimming pool and the like.
8. Accessories : Do not place this monitor on an unstable cart,
stand, tripod, bracket or table. The monitor may fall, causing s
erious injury to a child or adult and serious damage to the
appliance. Use only with a cart, stand, tripod. bracket or table
recommended by AASSET, or sold with the monitor. Any
mounting of the monitor should follow AASSET’s instructions and
should use a mounting accessory recommended by Samsung.
9. Ventilation : Slots and openings in the cabinet are provided for
Graphic Symbol Explanation ventilation and to ensure reliable operation of the monitor and to
The lightning flash with arrowhead symbol, protect it from overheating and these openings should never be
within an equilateral triangle, is intended to alert blocked by placing the monitor on a bed, sofa, rug or other similar
the user to the presence of uninsulated surface. This monitor should never be placed near or over a radia-
‘dangerous voltage’within the product’s tor or heat register. This monitor should not be placed in a built-in
enclosure that may be of sufficient magnitude installation such as a bookcase or rack unless proper ventilation is
to constitute a risk of electric shock to persons. provided or AASSET’s instructions have been adhered to.
The exclamation point within an equilateral
triangle is intended to alert the user to the 10. Power Sources :
This monitor should be operated only from the
presence of important operating and type of power source indicated on the making label. If you are not
maintenance (servicing) instructions in sure of the type of power supply to your installation site, consult
the literature accompanying the appliance. your Samsung dealer or local power company.
Warning - To Prevent Fire or Shock Hazard, 11. Grounding or Polarization :
For monitors equipped with a 3-wire
Do Not Expose This Monitor To grounding-type plug having a third(grounding) pin. This plug will
Rain or Moisture. only fit into a grounding type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the grounding-type plug.
IMPORTANT SAFEGUARDS 12. Power :
Cord Protection-Power supply cords should be routed so
that they are not likely to be walked on or pinched by items placed
-------------------------------------------------- upon or against them, paying particular attention to cords at plugs,
Caution convenience receptacles, and the point where they exit from the
monitor.
Power source is indicated on the rear of the set. It contains
high-voltage parts. If you remove the cover, it may cause fire 13. Lightning : For added protection for this monitor during a
or electric shock. Do not remove the cover by yourself. lightning storm or when it is left unattended and unused for long
(Control switches are at the front of the monitor.) periods of time, unplug it from the wall outlet and disconnect the
-------------------------------------------------- cable system. This will prevent damage to the monitor due to
lightning and power-line surges.
1. Read Instructions : All the safety and operating instructions 14. Overloading : Do not overload wall outlets and extension cords
should be read before the appliance is operated. as this can result in a risk of fire of electric shock.
2. Retain Instructions : The safety and operating instructions should 15. Object and liquid Entry : Never push objects of any kind into
be retained for future reference. this monitor through openings as they may touch dangerous
3. Heed Warnings : All warnings on the monitor and in the operating voltage points or short-out parts that could result in a fire or electric
instructions should be adhered to. shock. Never spill liquid of any kind on the monitor.
4. Follow Instructions : All operating and user instructions should be 16. Servicing : Do not attempt to service this monitor yourself as
followed. opening or removing cover may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service
5. Cleaning : Unplug this monitor from the wall outlet before cleaning. personnel.
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning. 17. Damage Requiring Service : Unplug this monitor from the wall
Exception. Amonitor that is meant for uninterrupted service outlet and refer servicing to qualified service personnel under the
and that for some specific reason, such as the possibility of the following conditions.
loss of an authorization code for a CATV converter, is not a. When the power-supply cord or plug is damaged.
intended to be unplugged by the user for cleaning or any other b. If liquid has been spilled or objects have fallen into the monitor.
purpose may exclude the reference to unplugging the monitor c. If the monitor has been exposed to rain or water.
in the cleaning description otherwise required in Item 5. d. If the monitor does not operate normally by following the oper-
ating instructions. Adjust only those controls that are covered by
6. Attachments : Do not use attachments not recommended by the operating instructions as an improper adjustment of other
AASSET as they may cause hazards. controls may result in damage and require extensive work by a
qualified technician to restore the monitor to its normal operation.
e. If the monitor has been dropped or the cabinet has been damaged.
f. When the monitor exhibits a distinct change in performance-this
indicates a need for service.
U
s
er manual
E
- 3 -

18.Replacement Parts : When replacement parts are required, radio/television technician for additional suggestions.
be sure the service technician has used replacement parts You may find the booklet called how to Identify and
specified by AASSET or have the same characteristics as Resolve Radio/TV Interference Problems helpful.
the original parts. This booklet was prepared by the Federal
Unauthorized substitutions may result in fire, electric shock or Communications Commission.
other hazards.
19. Safety Check : Upon completion of any service or repairs to
thismonitor, ask the service technician to preform safety
checks to determine that the monitor is in proper operating IC Compliance Notice
condition. This Class (A) digital apparatus meets all requirements of
the Canadian Interference-Causing Equipment Regulations.
NOTICE
Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURYAND This Class Adigital apparatus complies with Canadian
MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL , ICES-003.
STATE OR FEDERAL LAWS. Warning
This is a class Aproduct. In a domestic environment this
product may cause radio interference in which case the
user may be required to take adequate measures.
Warning
This equipment has been tested and found to comply the
limits for a class Adigital device, pursuant to part 15 of
the FCC Rules and ICES-003 of Industry Canada.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generate, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will
be required to correct the interference at his own
expense.
User-Installer Caution
Your authority to operate this FCC verified equipment
could be voided if you make changes or modifications not
expressly approved by the party responsible for
expressly approved by the party responsible for
Information to user
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class Adigital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions : (1)
this device may not cause harmful interference and (2)
this device must accept any interference received, includ-
ing interference that may cause undesired operation.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
U
s
er manual
E
- 4 -

Contents
IMPORTANT SAFETY INSTRUCTIONS..............2
IMPORTANT SAFEGUARDS.................................3
Contents.................................................................5
Unpacking..............................................................6
Names and Functions of Parts..............................6
Connecting to External Devices...........................7
Setup Menu Configurations...................................7
Appendix..............................................................11
Troubleshooting Guide........................................12
WEEE Symbols....................................................12
U
s
er manual
E
- 5 -

Unpacking
Remove the package cover and place the product on a flat and
securesurfaceorintheinstallationlocation.
Check whether all the following devices and accessories are.
included with the main system.
Names and Functions of Parts
Front Key Control
1. SOURCE /
Select input source, and move the previous menu.-
2. MENU
Activates and exits the On Screen Display.
OSD MENU(MAIN) : Input, Picture, OSD, Setup.
3. AUTO / ▼(DOWN)
This button is move the OSD menu, and use to auto
adjustment of VGA input only.
4. ▲ (UP) / MUTE
Move the OSD main menu or sub menu.
and Mute the Sound
EX) If you select the mute, then the picture below appears
On the screen
5. ◀ (LEFT) / Volume
This button will decrease the level of active function, and
move to the previous menu. Adjust the volume (decrease).
6. ▶ (RIGHT) / Volume
This button will increase the level of active function, and
select OSD menu. Adjust the volume (increase).
EX) If you select the volume, then the picture below appears
On the screen.
( Use the Remote controller and Key controls)
1. DC 12V IN
DC power Input
2. VGA IN
VGA Signal Input.
3. VIDEO A IN
Composite signal Input for VIDEO A
4. VIDEO A OUT
Video looping output for VIDEO A
5. VIDEO B IN
Composite signal Input for VIDEO B
6. VIDEO B OUT
Video looping output for VIDEO B
7. S-VIDEO (Y/C) IN
Y/C separated signal input
8. S-VIDEO (Y/C) OUT
Y/C separated signal looping output
9. PC STEREO IN
Bottom Panel Control
U
s
er manual
E
- 6 -
7. IR Sensor
Remote controller sensor.
8. POWER ON/OFF
Turns the power ON or OFF. There will be a few
seconds delay before the display appears
The power LED(next to the power switch) lights
green when the power is turned ON.
The power is turned off by pressing the power switch

U
s
er manual
Remote Controller
1. POWER( )
Turns the power ON or OFF. There will be a few seconds
delay before the display appears.
2. ID RESET
Reset the system id of remote controller.(Default system id is ‘1’)
3. P.MODE
Select Picture mode in Video. (Dynamic / Standard / Movie /
Custom)
4. AUTO
Auto geometry adjustment in VGA Source.
5. RETURN
Return to the previous menu.
6. MENU
Activates and exits the On Screen Display.
7. VOLUME, LEFT / RIGHT (◀/▶)
Adjust the volume , Increases or decreases the level of active
function, and right button is to select OSD menu, left button is
previous OSD menu.
8. UP / DOWN (▲/▼), MUTE
Move to OSD menu, and Mute the sound.
9. NUMBER Button
Change the SYSTEM ID for remote controller.
With the SYSTEM ID button pressed, entered the desired
NUMBER by pressing the corresponding button(0~9) to set up
the Remote Controller ID
10. SYSTEM ID
Set the system id of remote controller.
11. BRIGHT, CONTRAST, COLOR, SHARPNESS
Simply control brightness, contrast, color, sharpness via the
remote controller.
12. INFO
Display information of the picture.
.
13. SOURCE
Select VGA or Video (Video A / Video B / S-Video) sources.
14. ENTER
Select OSD main menu or sub menu.
Connecting to External Devices
The product can be connected to an external device such as
Camera, DVR,VCR, etc.
Setup Menu Configurations
When there is no connection at the VGA and Video input, the On
Screen Display will show this message.
MENU SELECTION
1. Press the MENU button and then ▲/▼ button to display each
menu.
2. Press the ENTER or ▶ button and then ▲/▼button to select
the menu item.
3. Press the MENU button to return to normal picture.
NOTE : If you don’t connect to VGA port, menu is not displayed
in VGA mode.
A. INPUT MENU
OSD MENU DESCRIPTION
NO SIGNAL DISPLAY
E
- 7 -

 B. PICTURE MENU (Video mode)
Mode
URE MODE (VGA)
 C. PICTURE MODE (VGA)
 C. PICTURE MODE (VGA)
Custom
- NTSC input
U
s
er manual
Inputs can be set to Video A, Video B, S-Video, VGA mode.
1. Press the MENU button and then▲/▼button to select the Input menu.
2. Press the ENTER or ▶ button to select the Source List.
3. Press the ENTER or ▶ button and then▼/▲button to select
the input source.
4. Press the ENTER button to change the input source.
You can also select the input source with SOURCE on the
Remote Control
- PAL input
1. Press the MENU button and then_▲/▼button to select the
picture menu.
2. Press the ENTER or ▶ button to select the the Mode
3. Press the ENTER or ▶ button and then▼/▲button to
Select the picture Mode.
4. Press the ENTER button to save
You can also recall a desired picture mode with P.MODE on
the Remote Controller.
1. Press the ENTER or▲/▼button to select Custom in the Picture menu.
2. Press the▼/▲button and then ENTER or ▶ button to select
the adjustment item you need.
EX) If you select the Brightness, then the picture below appears
on the screen
3. Press the ◀/▶ button to increase or decrease level.
4. Press the ▲/▼ button to select the other item.
5. Press ENTER button to save.
You can also recall a desired Brightness, Contrast, Color or
Sharpness with BRIGHT, CONTRAST,
COLOR or SHARPNESS on the Remote Control.
NOTE : Tint item is NTSC input only.
Adjustment
E
- 8 -

U
s
er manual
1. Press the MENU button and then▲/▼button to select
the Picture menu.
2. Press the ENTER or ▶ button to select the Adjustment.
3. Press the ENTER or ▶ button and then▼/▲button to select
The item to adjust.
EX) If you select the Brightness, then the picture below will
appear on the screen.
4. Press the ◀/▶ button to increase or decrease level.
5. Press the ▲/▼ button to select the other item.
6. Press ENTER button to save.
Color Tone
1. Press the MENU button and then▲/▼ button to select the
Picture menu.
2. Press the ENTER or ▶ button to select the Color Tone.
3. Press the ENTER or ▶ button and then ▲/▼ button to select
the Color Tone.
4. Press the ENTER button to save.
User
1. Press the MENU button and then ▲/▼ button to select the
Picture menu.
2. Press the ENTER or ▶ button and then Press the ▲/▼ button
to select the User.
3. Press the ENTER or ▶ button and then Press the ▲/▼ button
to select the adjust the menu item you need.
EX) If you select the Red, then the picture above will appear
on the screen.
4. Press the ◀/▶ button to increase or decrease level.
5. Press the ▲/▼ button to select the other item.
6. Press ENTER button to save.
D.OSD MENU
Transparency or OSD Timer
1. Press the MENU button and then ▲/▼ button to select the
OSD menu.
2. Press the ENTER or ▶ button and then ▲/▼ button to
select Transparency or OSD Timer.
EX) If you select OSD Timer, then the picture below will
appear on the screen.
3. Press the ◀/▶ button to increase or decrease level.
4. Press the ▲/▼ button to select the other item.
5. Press the ENTER button to save.
No Signal
1. Press the MENU button and then Press the ◀/▶button to
select the OSD menu.
2. Press the ENTER or ▶ button and then Press the ◀/▶ button
to select the No Signal.
3. Press the ENTER or ▶ button and then Press the ◀/▶ button
to select the On or Off.
4. Press the ENTER button to save.
ghtness
❷
E
- 9-

U
s
er manual
Language
1. Press the MENU button and then▲/▼ button to select the
OSD menu.
2. Press the ENTER or ▶ button and then Press the ▲/▼
button to select the Language.
3. Press the ENTER or ▶ button and then Press the ▲/▼
button to select the language you need.
4. Press the ENTER button to save.
 E. SETUP MENU
Default
Reset to original factory value.
1. Press the MENU button and then _/❷ button to select the
Setup menu.
2. Press the ENTER or ❿ button to select the Default.
3. Press the ENTER or ❿ button and then _/❷ button to
select the Cancel or Ok.
4. Press the ENTER or ❿ button to save.
System ID
Change the system id. (Factory default is ‘1’)
1. Press the MENU button and then▲/▼ button to select the
Setup menu.
2. Press the ENTER or ▶ button and then ▲/▼ button to select
the System ID.
3. Press the ENTER or ▶ button and then ▲/▼ button to select
the ID.
4. Press the ENTER or▶ button to save.
Information
Display the information of current source.
1. Press the MENU button and then ▲/▼ button to select the
Setup menu.
2. Press the ENTER or ▶ button and then ▲/▼ button to select
the Information.
3. Press the ENTER or ▶ button to display the information.
E
- 10 -

Model Name PAC-171AV
Composite 2ch input 1.0Vp-p, 75Ωterminated, loop-through out
S-VIDEO 1ch input (Y/C) , loop-through out
Video
VGA 1ch input
Resolution 1280x1024@60Hz
Horizontal(KHz) 31KHz ~ 80KHz
Frequency
Vertical(Hz) 50Hz ~ 75Hz
720x480@60Hz,720x576@50Hz,800x600@60/75Hz
VGA Mode
1024x768@60/75Hz, 1280x1024@60/75Hz
Power Consumption Max. 36W
Net
382.4x390.5x200mm
Dimensions
(WxDxH)
Packing
436x476x225mm
Net Weight
5.96Kg
Weight(kg)
Gross Weight
7.67Kg
Power Supply DC 12V / 3A
Operating Temperature
50 ° F~104 ° F (10 ° C~40 ° C)
Operating Humidity 10%~80%,Non-condensing
Considerations Storage Temperature
- 4 ° F~113 ° F (-20 ° C~45 ° C)
Environmental
Considerations
Storage Humidity 5%~95%,Non-condensing
Size 17" Diagonal AM-TFT
Active Display Area 337.92x270.336mm
Pixel Pitch(mm) 0.264mm(H) x 0.264mm(V)
Brightness(cd/m2)
300cd/m2
Contrast Ratio
700:1
Response Time(ms)
8ms
LCD Panel Spec
Viewing Angle(L/R/ T/B)
75/75/75/60
System
U
s
er manual
Auto Adjustment (VGA mode only)
E
Full auto configuration in the VGA mode.
1. Press the MENU button and then ▲/▼ button to
select the Setup menu.
2. Press the ENTER or ▶ button and then ▲/▼
button to select the Auto Adjustment.
3. Press the ENTER or▶ button and then Press the
▲/▼_button to select the Cancel or Ok.
- 11 -

U
s
er manual
E
- 12 -

- 13 -