Palmer Industries CANTILEVER SHELVING User manual

SHELVING SYSTEM ASSEMBLY INSTRUCTIONS
rev: 052020
© 2020 Palmer Industries, Inc. PalmerIndustries.com 401- 421-1730 OVER
WOOD SCREW
WALL FLANGE
TEE
FINIAL
MAY NOT BE SAME
STYLE AS SHOWN
FINIAL
MAY NOT BE SAME
STYLE AS SHOWN
ARM
SHELF
SUPPORT POST
TEE
PINNED IN POSITION
DO NOT REMOVE
10-32 X 3/16”
POINTED
SET SCREW
10-32 X 1/8”
FLAT
SET SCREW
1/4”-20 X 1/4”
SET SCREW
HEX
WRENCH
IN-WALL
BLOCKING
REQUIRED
RUBBER BUMPERS ARE
APPLIED TO UNDERSIDE
OF GLASS SHELF
AT ARM LOCATIONS
RACK
CANTILEVER
SHELVING
SHELVING
SYSTEMS
PALMER INDUSTRIES
CUSTOM ARCHITECTURAL METALWORK
PALMER
INDUSTRIES
MOUNTING TO WALL ONLY
CONTACT PALMER WITH
ANY INSTALLATION QUESTIONS
401-421-1730

SHELVING SYSTEM ASSEMBLY INSTRUCTIONS
rev: 052020
© 2020 Palmer Industries, Inc. PalmerIndustries.com 401- 421-1730
IN-WALL
BLOCKING
REQUIRED
WOOD SCREW
WALL FLANGE
SUPPORT POST
TEE
10-32 X 3/16”
POINTED
SET SCREW
10-32 X 1/8”
FLAT
SET SCREW
RACK
CANTILEVER
SHELVING
SHELVING
SYSTEMS
PALMER INDUSTRIES
MOUNTING TO WALL ONLY
CAREFULLY UNPACK AND INSPECT YOUR PALMER PRODUCT.
THE SHELVING UNIT SHOULD BE CAREFULLY ASSEMBLED ON A CLEAN AND PADDED SURFACE TO AVOID ANY SCRATCHING
OR DAMAGE. FOR UN-LACQUERED BRASS FINISHES, PLEASE WEAR CLEAN GLOVES TO PREVENT FINGERPRINTS.
THE BOTTOM WALL MOUNT TEE IS PERMANENTLY PINNED INTO POSITION - DO NOT REMOVE.
ALL COMPONENTS MUST BE SLID DOWN OVER THE TUBE FROM THE TOP.
PLEASE BE VERY CAREFUL NOT TO SCRATCH THE TUBE WHEN ASSEMBLING THE COMPONENTS.
PAY PARTICULAR ATTENTION THAT NO SET SCREWS PROTRUDE INSIDE THE FITTING TO AVOID SCRATCHES.
ASSEMBLE THE COMPONENTS ONTO THE SUPPORT POSTS AND SPACE ACCORDING TO THE CUSTOMER DRAWING.
POSITION THE WALL FLANGES SO THAT THEY ARE IN ALIGNMENT WITH THE SOLID WOOD BLOCKING. MAKE SURE
THE COMPONENTS ARE BURR FREE AND THE SET SCREWS (IF INSTALLED) ARE BACKED OUT FAR ENOUGH TO
AVOID SCRATCHING THE POSTS.
TIGHTEN THE SET SCREWS ONLY ENOUGH TO KEEP THE COMPONENTS FROM SLIDING - FINAL TIGHTENING AND
ADJUSTING WILL BE DONE AFTER THE FLANGES HAVE BEEN SECURED TO THE WALL.
CAREFULLY PLACE THE POST ASSEMBLIES INTO POSITION ON THE WALL, AND MARK THE NECESSARY SCREW
LOCATIONS. DRILL APPROPRIATE PILOT HOLES FOR THE SCREWS.
SEPARATE THE WALL FLANGES FROM THE TEES BY LOOSENING THE 10-32 X 3/16” POINTED SET SCREWS.
SECURE THE WALL FLANGES TO THE WOOD BLOCKING IN THE WALL WITH THREE PROVIDED WOOD SCREWS EACH.
SECURE THE SUPPORT POSTS TO THE WALL FLANGES. THE UPPER TEE MAY BE ADJUSTED SLIGHTLY TO HELP
LOCATE ONTO THE WALL FLANGES. IT IS IMPORTANT THAT THE TEES ARE SECURED TO THE WALL FLANGES USING
THE PROVIDED 3/16” POINTED SET SCREWS.
WHEN ALL FLANGE COMPONENTS ARE PROPERLY ALIGNED, TIGHTEN SET SCREWS SECURELY.
CORRECTLY POSITION ARMS AND TIGHTEN 1/4”-20 SET SCREWS SECURELY.
3
1
2
5
4
6