Panasonic P2HD AG-HPX610P User manual

Operating Instructions
Memory Card Camera-Recorder
Before operating this product, please read the instructions carefully and save this manual for future use.
ENGLISH
VQT5L25A(E)
W0914HM0 -YI
Model No. AG-HPX610P
Model No. AG-HPX610EJ

Read this rst! (For AG-HPX610P/AG-HPX610EJ)
– 2 –
Read this rst! (For AG-HPX610P/AG-HPX610EJ)
indicates safety information.
WARNING:
• To reduce the risk of fire, do not expose this
equipment to rain or moisture.
• To reduce the risk of fire, keep this equipment
away from all liquids. Use and store only in
locations which are not exposed to the risk of
dripping or splashing liquids, and do not place
any liquid containers on top of the equipment.
WARNING:
Always keep memory cards (optional accessory)
out of the reach of babies and small children.
CAUTION:
To reduce the risk of fire and annoying interference,
use the recommended accessories only.
CAUTION:
To reduce the risk of fire, refer mounting of the
optional interface boards to qualified service
personnel.
CAUTION:
Do not jar, swing, or shake the unit by its handle
while the conversion lens or another accessory is
attached.
Due to the added weight of the conversion lens,
any strong jolt to the handle may damage the unit
or result in personal injury.
CAUTION:
In order to maintain adequate ventilation, do not
install or place this unit in a bookcase, built-in
cabinet or any other confined space. To prevent
risk of fire hazard due to overheating, ensure that
curtains and any other materials do not obstruct
the ventilation.
CAUTION:
Do not lift the unit by its handle while the tripod is
attached. When the tripod is attached, its weight
will also affect the unit’s handle, possibly causing
the handle to break and hurting the user. To carry
the unit while the tripod is attached, take hold of
the tripod.
CAUTION:
Excessive sound pressure from earphones and
headphones can cause hearing loss.
CAUTION:
Do not leave the unit in direct contact with the skin
for long periods of time when in use.
Low temperature burn injuries may be suffered if
the high temperature parts of this unit are in direct
contact with the skin for long periods of time.
When using the equipment for long periods of
time, make use of the tripod.
CAUTION:
A coin type battery is installed inside of the unit.
Do not store the unit in temperatures over 60 °C
(140 °F).
Do not leave the unit in an automobile exposed to
direct sunlight for a long period of time with doors
and windows closed.
Battery recycling symbol (valid only in Taiwan)

Read this rst! (For AG-HPX610P)
– 3 –
FCC NOTICE (USA)
Declaration of Conformity
Model Number: AG-HPX610P
Trade Name: Panasonic
Responsible Party: Panasonic Corporation of North America
Two Riverfront Plaza, Newark, NJ 07102
Support contact: 1-800-524-1448
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
To assure continued compliance, follow the attached installation instructions and do not make any
unauthorized modifications.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The user may find the booklet “Something About Interference”
available from FCC local regional offices helpful.
Warning:
To assure continued FCC emission limit compliance, follow the attached installation instructions and the user
must use only shielded interface cables when connecting to host computer or peripheral devices. Also, any
unauthorized changes or modifications to this equipment could void the user’s authority to operate this device.
NOTIFICATION (Canada)
CAN ICES-3 (B)/NMB-3(B)
Read this rst! (For AG-HPX610P)
indicates safety information.
A rechargeable battery that is recyclable powers the product you have purchased.

Read this rst! (For AG-HPX610EJ)
– 4 –
Read this rst! (For AG-HPX610EJ)
indicates safety information.
EEE Yönetmeliğine Uygundur.
EEE Complies with Directive of Turkey.
Manufactured by: Panasonic Corporation, Osaka, Japan
Importer’s name and address of pursuant to EU rules:
Panasonic Marketing Europe GmbH
Panasonic Testing Centre
Winsbergring 15, 22525 Hamburg, Germany
EMC NOTICE FOR THE PURCHASER/USER OF THE APPARATUS
1. Applicable standards and operating environment
The apparatus is compliant with:
• standards EN55103-1 and EN55103-2, and
• electromagnetic environments E1, E2, E3 and E4.
2. Pre-requisite conditions to achieving compliance with the above standards
<1> Peripheral equipment to be connected to the apparatus and special connecting cables
• The purchaser/user is urged to use only equipment which has been recommended by us as peripheral equipment
to be connected to the apparatus.
• The purchaser/user is urged to use only the connecting cables described below.
<2> For the connecting cables, use shielded cables which suit the intended purpose of the apparatus.
• Video signal connecting cables
Use double shielded coaxial cables, which are designed for 75-ohm type high-frequency applications, for SDI
(Serial Digital Interface).
Coaxial cables, which are designed for 75-ohm type high-frequency applications, are recommended for analog
video signals.
• Audio signal connecting cables
If your apparatus supports AES/EBU serial digital audio signals, use cables designed for AES/EBU.
Use shielded cables, which provide quality performance for high-frequency transmission applications, for analog
audio signals.
• Other connecting cables
Use shielded cables, which provide quality performance for high-frequency applications, such as connecting
cables for IEEE1394 or USB.
• When connecting to the HDMI signal terminal, use multilayer shielded cables, which provide quality performance
for high-frequency applications.
• When connecting to the DVI signal terminal, use a cable with a ferrite core.
• If your apparatus is supplied with ferrite core(s), they must be attached on cable(s) following instructions in this
manual.
3. Performance level
The performance level of the apparatus is equivalent to or better than the performance level required by these
standards.
However, the apparatus may be adversely affected by interference if it is being used in an EMC environment, such as an
area where strong electromagnetic fields are generated (by the presence of signal transmission towers, cellular phones,
etc.). In order to minimize the adverse effects of the interference on the apparatus in cases like this, it is recommended
that the following steps be taken with the apparatus being affected and with its operating environment:
1. Place the apparatus at a distance from the source of the interference.
2. Change the direction of the apparatus.
3. Change the connection method used for the apparatus.
4. Connect the apparatus to another power outlet where the power is not shared by any other appliances.
CAUTION:
Do not remove panel covers by unscrewing.
No user serviceable parts inside. Refer servicing to qualified service personnel.

Read this rst! (For AG-HPX610EJ)
– 5 –
Декларація про Відповідність
Вимогам Технічного Регламенту Обмеження Використання деяких Небезпечних Речовин в
електричному та електронному обладнанні
(затвердженого Постановою №1057 Кабінету Міністрів України)
Виріб відповідає вимогам Технічного Регламенту Обмеження Використання деяких Небезпечних Речовин в електричному та
електронному обладнанні (ТР ОВНР).
Вміст небезпечних речовин у випадках, не обумовлених в Додатку №2 ТР ОВНР, :
1. свинець(Pb) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на мільйон;
2. кадмій (Cd) – не перевищує 0,01 % ваги речовини або в концентрації до 100 частин на мільйон;
3. ртуть(Hg) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на мільйон;
4. шестивалентний хром (Cr6+) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на мільйон;
5. полібромбіфеноли (PBB) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на мільйон;
6. полібромдефенілові ефіри (PBDE) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на мільйон.
EU
TO REMOVE BATTERY
Main Power Battery (Ni-Cd / Ni-MH / Li-ion Battery)
• To detach the battery, please proceed in the reverse order of the installation method described in this manual.
• If a battery made by any other manufacturer is to be used, check the Operating Instructions accompanying the battery.
Back-up Battery (Lithium Battery)
• For the removal of the battery for disposal at the end of its service life, please consult your dealer.

– 6 –
fThe SDHC logo is a trademark of SD-3C, LLC.
fHDMI, HDMI logo, and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and/
or other countries.
fMMC (Multi Media Card) is a registered trademark of Inneon Technologies AG.
fMicrosoft and Windows are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.
fScreenshots are used according to Microsoft Corporation guidelines.
fApple, Macintosh, Mac OS, and QuickTime are trademarks or registered trademarks of Apple Inc. in the United States and/or other countries.
fUniSlot is a registered trademark of Ikegami Tsushinki Co., LTD.
fAll other names, company names, product names, etc., contained in this instruction manual are trademarks or registered trademarks of their
respective owners.
fThis product is licensed under the AVC Patent Portfolio License. All other acts are not licensed except private use for personal and non-prot purposes
such as what are described below.
-To record video in compliance with the AVC standard (AVC Video)
-To play back AVC Video that was recorded by a consumer engaged in a personal and non-commercial activity
-To play back AVC Video that was obtained from a video provider licensed to provide the video
Visit the MPEG LA, LLC website (http://www.mpegla.com/) for details.
fUse of DCF Technologies under license from Multi-Format, Inc.
How to read this document
rIllustrations
fIllustrations of the camera, menu screens, and other items, may vary from the actual items.
rReference pages
fReference pages in this document are indicated by (page 00).
rTerminology
fBoth SD memory card and SDHC memory card are referred to as SD memory card.
fMemory card that has the “P2” logo (such as optional AJ-P2E064FG) is referred to as “P2 card”.
fMemory card that has the “microP2” logo (such as optional AJ-P2M032AG) is referred to as “microP2 card”. To use, insert it into the microP2 card
adaptor AJ-P2AD1G (optional).
fP2 memory card and microP2 memory card are referred to only as “P2 card” unless distinguished otherwise.
fVideo that is created during a single recording operation is referred to as a “clip”.

Contents
– 7 –
Contents
Read this rst! (For AG-HPX610P/AG-HPX610EJ) 2
Read this rst! (For AG-HPX610P) 3
Read this rst! (For AG-HPX610EJ) 4
Chapter 1 Overview 9
Before using the camera 1 0
Main features 11
Features of the camera unit 1 2
Features of recorder/play unit 1 3
How to use the camera 1 5
Editing, saving using external equipment 15
System conguration 1 6
Accessories 1 8
Chapter 2 Description of Parts 19
Power supply and accessory mounting section 2 0
Audio (input) function section 2 1
Audio (output) function section 22
Shooting and recording/playback functions section 23
Menu operation section and thumbnail operation section 2 6
Time code section 27
Warning and status display section 2 8
SmartUI display ([HOME] screen) 2 9
Chapter 3 Recording and Playback 30
Setting the date/time of the internal clock 3 1
P2 card 32
Inserting a P2 card 32
Removing a P2 card 32
Preventing accidental erasure 33
P2 card access LEDs and status of P2 cards 33
P2 card recording time 33
How to handle data recorded on P2 cards 34
Basic procedures 3 5
For shooting 35
Standard recording 36
Standard recording and native recording 37
Standard recording (Pull-down recording) 37
Native recording 37
Variable frame rate (VFR) recording function (extra-cost
option) 3 8
Native variable frame rate recording 38
Standard variable frame rate recording (pull-down recording) 38
Using the variable frame rate recording function 38
Special recording functions 4 1
Pre-recording 41
Interval recording 41
One-shot recording 42
Loop recording 42
One-clip recording 43
Proxy recording function (extra-cost option) 44
Hot swap recording 44
Rec review function 44
Shot mark recording function 44
Text memo recording function 45
Normal and variable speed playback 4 6
Chapter 4 Adjustments and Settings for
Recording 47
Multi formats 4 8
Selecting recording signals 48
Recording formats and recording playback times 48
List of recording settings and recording functions 48
Selecting video output 4 9
List of recording/playback and output formats 49
Adjusting the white and black balance 5 3
Adjusting the white balance 5 3
Adjusting the black balance 5 5
Setting the electronic shutter 5 6
Setting the shutter mode and speed 56
Setting the synchro scan mode 56
Flash band compensation (FBC) function 5 8
Setting the ash band compensation function 58
Assigning functions to <USER> buttons 59
Selecting audio input and adjusting recording levels 6 0
Selecting audio input signals 60
Adjusting the recording levels 60
Selecting <F.AUDIO LEVEL> dial function 60
Setting the time data 61
Recording and output of time codes and user bits 61
User bits settings 64
How to input user bits 64
Setting the time code 66
Externally locking the time code 67
Supplying time codes to external devices 68
Connecting and setting the generator lock and time code
input/output 69
Counter setting and display 6 9
Viewnder status display 7 0
Lamp display in the viewnder 7 0
Mode check screen displays (mode check function) 70
Conguration of status display on viewnder screen 71
Selecting display items on viewnder screen 71
Screen display 71
Information display in center 75
Checking and displaying shooting status 76
Mode check display 78
Center marker display 79
Safety zone display 79
Zebra patterns display 80
Focus assist function 80
Waveform monitor function 81
Handling setting data 8 2
Setting data le conguration 82
Handling SD memory cards 82
Performing operations on SD memory cards 83
How to use scene le data 84
Saving scene les, etc. to SD memory cards 85
Chapter 5 Preparation 87
Power supply 8 8
Mounting and setting battery 88
Using external DC power supply 89
Mounting and adjusting the lens 9 1
Mounting the lens 91
Flange back adjustment 91
White shading compensation 92
Chromatic aberration compensation function (CAC) 93
Preparing for audio input 9 6
Using the front microphone 96
Using a wireless receiver 96
Using audio devices 96
Mounting accessories 97
Mounting the camera on a tripod 97
Attaching the shoulder strap 97
Attaching the rain cover 98
Connecting the <DC OUT> terminal with the external
recording start/stop switch 9 9
Chapter 6 Thumbnail Operations for Clips 100
Thumbnail operations 101
Thumbnail operation overview 101
Thumbnail screen 102
Selecting thumbnails 103
Playing back clips 104
Switching the thumbnail display 104
Changing thumbnails 104
Shot mark 105
Text memo 105
Deleting clips 107
Restoring clips 107
Reconnecting incomplete clips 107
Copying clips 108
Setting clip metadata 108
Formatting a P2 card 111
Formatting SD memory cards 111
Setting the thumbnail display 111
Properties 11 2
Chapter 7 Menu Operations 115
Displaying the setting menu on the viewnder screen 116

Contents
– 8 –
Setting menu basic operations 11 6
Menu direct close function 11 7
Changing setting values quickly (only for [MASTER PED] and
[H PHASE]) 11 7
Initializing the setting menu items 11 7
Setting menu structure 118
Menu list 120
[SCENE FILE] screen 120
[SYSTEM SETUP] screen 122
[SW MODE] screen 123
[RECORDING SETUP] screen 124
[AUDIO SETUP] screen 125
[IN/OUT SEL] screen 127
[DISPLAY SETUP] screen 127
[BATTERY SETUP] screen 128
[CARD FUNCTIONS] screen 130
[LENS SETUP] screen 130
[PROXY SETTING] screen 131
[PC/USB/LAN] screen 131
[OTHER FUNCTIONS] screen 132
[DIAGNOSTIC] screen 133
Chapter 8 Using SmartUI 134
Setting menu basic operations 135
SmartUI basic operations 135
Initializing SmartUI setting menu items 135
Setting menu structure 136
SmartUI menu operation overview
137
Menu list 138
[CAMERA] screen 138
[AUDIO] screen
140
[SETUP] screen 142
[TEXT MEMO] screen 144
Chapter 9 Connecting to External Devices 145
Connection through the <USB2.0> terminal 146
USB connection to a computer in the device mode 146
USB host mode 146
Connecting to the remote control unit (AJ-RC10G) 151
Connecting to the extension control unit (AG-EC4G) 152
Chapter 10 Maintenance and Inspection 153
Inspections before shooting 154
Preparing to inspect 154
Inspecting the camera unit 154
Inspecting the memory recording functions 154
Maintenance 156
Charging the built-in battery 156
Warning system 157
Warnings description list 157
Error code 158
Card warning code 158
Warning/error displays in the thumbnail operation and the
USB host mode 158
Updating the camera rmware 160
Chapter 11 Additional Functions from the
Optional Board 161
Video encoder board (AG-YDX600G) 162
Proxy settings 162
Recording the proxy data 163
Recording to the SD memory card 163
Checking the proxy data 164
Error displays about proxy data recordings 165
HD/SD SDI input board (AG-YA600G) 167
Chapter 12 Specication 168
Dimensions and specications 169
Dimensions 169
Specications 169
Details of the connector signals 173
Index 176

Before using the camera, read this chapter, and check its features
and accessories. Function extensions as extra-cost options are also
explained.
Chapter 1 Overview

– 10 –
Chapter 1 Overview — Before using the camera
Before using the camera
rCaution regarding laser beams
The MOS sensor may be damaged if the MOS sensor is subjected to light from a laser beam.
Make sure that laser beams do not strike the lens when shooting in an environment where laser devices are used.
rNote the following points.
fWhen preparing to record important images, always shoot some advance test footage to verify that both pictures and sound are being recorded
normally.
fShould video or audio recording fail due to a malfunction of the camera or the P2 cards used, we will not assume liability for such failure.
rWhat to remember when throwing memory cards away or transferring them to others
Formatting memory cards or deleting data using the functions of the camera or a computer will merely change the le management information: it will
not completely erase the data on the cards. When throwing these cards away or transferring them to others, either physically destroy them or use a
data deletion program for computers (commercially available) to completely erase the data. Users are responsible for managing the data stored in their
memory cards.
rSoftware information about this product
1 This product includes software licensed under GNU General Public License (GPL) and GNU Lesser General Public License (LGPL), and
customers are hereby notied that they have rights to obtain, re-engineer and redistribute the source code of these software.
2 This product includes software licensed under MIT-License.
3 This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/).
4 This product includes software licensed under OpenBSD License.
5 This product includes PHP, freely available from <http://www.php.net/>.
6 This software is based in part on the work of the Independent JPEG Group.
7 This product includes software licensed under MOZILLA PUBLIC LICENSE.
For details (which are originally provided in English) and how to obtain the source code, visit the following website.
http://pro-av.panasonic.net/
We do not accept inquiries about the details of the source code obtained by the customer.
rPrecautions when installing USB drivers
For the latest information on the driver, visit the following website.
http://pro-av.panasonic.net/
fInstall the required driver into your computer from the website.
fFor installation procedure of the driver, refer to the installation manual on the website.

– 11 –
Chapter 1 Overview — Main features
Main features
The P2 memory card camera-recorder AG-HPX610P/AG-HPX610EJ incorporates the MOS sensor newly developed for the camera unit to ensure that
high-sensitivity F12 (59.94 Hz), high-resolution, and high-quality video can be obtained. The camera also uses a 2/3-inch lens mount to accommodate
many existing interchangeable lenses and features a compact body to provide amazing action for a body weight of approximately 2.8 k].
The camera supports 50 Hz/59.94 Hz switchable and HD/SD multi-format. The AVC-Intra, DVCPRO HD, DVCPRO50, DVCPRO, and DV compression
recording formats can be selected, and the reliability, instantaneousness and IT functions expected of P2 helps revolutionize work ow.
An add-on system for optional functions (extra-cost options) is also available for selecting and installing only required functions.
rFunction extension (extra-cost options)
As of start of sales, the following functions (extra-cost options) are available:
fVideo encoder board AG-YDX600G
This enables proxy recording. This is effective in checking and editing clips.
fHD/SD SDI input board AG-YA600G
This enables recording of the SDI signal input from the <SDI OUT/IN (OP)> terminal.
fUpgrade Software Key AG-SFU601G (Network function)
This enables addition of text memos from IT devices.
In explanations from here on, this option is referred to as “network function (extra-cost option)”.
fUpgrade Software Key AG-SFU602G (Production pack)
This allows the following functions to be used to achieve substantial video production functions:
-1080/23.98PsF system
-Variable frame rate (VFR) recording function
In explanations from here on, this option is referred to simply as “production pack (extra-cost option)”.
fUpgrade Software Key AG-SFU603G (UPLINK device control function)
This enables starting and stopping UPLINK device data transfer, displaying the connection status icon, and displaying detailed information about the
device.
In explanations from here on, this option is referred to as “UPLINK device control function (extra-cost option)”.
fUpgrade Software Key AG-SFU604G (Playlist edit function)
This is a function that edits the playlist by using proxy video.
This enables editing/saving the playlist, creating a new clip by using a playlist (edit copy), and SDI playback of the playlist.
In explanations from here on, this option is referred to as “Playlist edit function (extra-cost option)”.
r50 Hz/59.94 Hz switchable and HD/SD multi-format
Recording by the HD/SD video format is supported. 50 Hz/59.94 Hz switchable accommodates all kinds of applications and global content production
in addition to news reporting and program/video production. For 1080i/720P HD recording, the highly reliable AVC-Intra/DVCPRO HD codecs can be
selected for broadcasting use, and for SD video, the DVCPRO50/DVCPRO/DV multi-codecs can be selected.
4-channel recording (all formats) is provided for 16-bit/48 kHz non-compressed high-quality audio.
rSmartUI
New operability is provided by integrating the conventional LCD window and audio selector switches. Remote control from IT devices and other
functionality ensure expandability for future applications.

– 12 –
Chapter 1 Overview — Features of the camera unit
Features of the camera unit
rProgressive 2/3-inch MOS sensor
It incorporates a newly developed 2/3-inch MOS sensor to ensure high-sensitivity and high-resolution video.
r14-bit digital circuit
The camera has in-built high performance DSP (digital signal processor) for processing 14-bit signal input and 20-bit internal computations. This circuit
sets gamma and other corrections for each R/G/B color of 1080/60P video, and batch processes up to conversion (P/I conversion, line conversion, down
conversion) to various HD/SD formats. This ensures high-resolution video output in any video format.
rSeven gamma curve modes including cine-like gamma
You can select from seven gamma curve modes, including cine-like gamma for easily reproducing lm-like tones, for greater breadth in video
production.
rSlow/synchro/high-speed shutter
The shutter speed can be selected at will from the slowest speed of 1/12 seconds up to the highest speed of 1/7200 seconds*. The synchro scan
function suited to recording on monitor screens can also be provided.
* The above is the shutter value when the [SYNCHRO SCAN] item on the [SCENE FILE] screen is set to [3d].
rShooting assist function
f<USER> buttons (<USER MAIN>/<USER1>/<USER2>):
Frequently used functions can be assigned to the three <USER> buttons (<USER MAIN>/<USER1>/<USER2>) and executed by simply pressing the
required button.
fFocus assist:
Enlarging the the center part of the screen and displaying the focus bar assist focusing.
fEight lens chromatic aberration les/four shading compensation les that are compatible with replacement lenses provided
fColor temperature conversion:
Color-temperature can be ne-adjusted after the white balance is set.
fRec review function:
The last several seconds of the previously recorded clip can be quickly checked.
fEquipped with optical ND lters at four positions
rChromatic aberration compensation function (CAC)
The camera is equipped with a function to automatically correct registration error that occurs mainly due to slight chromatic aberration, etc., which
cannot be compensated on the lens itself, and minimizes color smearing in peripheral images.
rRemote control supported
The remote control unit (optional/AJ-RC10G) and extension control unit (optional/AG-EC4G) are supported. You can control the camera, such as
adjusting the camera image or performing recording operations, remotely while monitoring the camera image.
rAuto tracking white balance (ATW) function
The white balance is automatically adjusted according to the subject in real time. This feature is effective when you have no margin for adjusting white
balance manually, for example, when recording in an emergency.
rDynamic range stretcher (DRS) function
With this function, the video signal level of high brightness areas that may be skipped with white blanks in regular recording methods can be expanded
by compressing images and maintaining the contrast.*
* The dynamic range stretcher function does not work in the 1080/24P, 1080/30P, and 1080/25P modes.
rCamera extension system
By combining the optional camera adaptor (AG-CA300G) and base station (AG-BS300), you can operate the camera as a camera extension system.
For connections with these devices, refer to the connection methods and precautions described in the instruction manual of each device.
The camera only supports the HD viewnder. To display return video images on the viewnder screen with the system where the optional VF interface
box (AG-YA500G) is connected, set the [SYSTEM MODE] item to [1080-59.94i] or [1080-50i]. The [SYSTEM MODE] item can be selected from the
setting menu [SYSTEM SETUP] screen.
rViewnder connection
1080/59.94i or 1080/50i signals are output from the viewnder connector of the camera.
By connecting the optional view nder (AG-CVF10G, AJ-HVF21KG, AJ-CVF100G), images compatible with multi-format can be viewed.

– 13 –
Chapter 1 Overview — Features of recorder/play unit
Features of recorder/play unit
rVarious interfaces
f<USB2.0> terminal (host/device) provided
By connecting to a computer via USB 2.0, the P2 card inserted on the camera can be used as mass storage.
The camera also incorporates the USB host function, allowing data on the P2 card to be saved on the hard disk drive connected with USB 2.0 or clips
saved on the hard disk drive to be viewed or written back to the P2 card.
f<LAN> terminal provided
By installing the network function (extra-cost option), metadata can be input from a computer.
rLarge-capacity, high-speed transfer, highly reliable P2 card
P2 cards are semiconductor memory that is highly resistant to impact, vibration and temperature changes, and are highly reliable since they have
no parts that rotate or contact other parts when recording or playing back, like on tape or disk, which enables these cards to be repeatedly used for
recording and initialized over a prolonged period of time. Connectors have also been designed for professional use to ensure greater durability when
cards are removed or inserted.
Recorded A/V data is recorded to P2 cards as les for individual cuts that do not require digitizing, which means that they are ready for nonlinear editing
or transfer over a network. Optical disks can be worked on at ease at an amazing transfer speed. The PC card standard is also supported, which means
that PC cards can be plugged in directly to the PC card slot on your computer.*1
The unit is equipped with two P2 card slots, enabling continuous recordings for two P2 cards, and they also provide the following recording capabilities
specic to memory card recorders:
fCard selection:
The recording slot can be selected (switched) in a standby state*2. When recording material is forwarded immediately after it is recorded for editing or
transmission, recording can be continued by an interruption far shorter than by tape or disk replacement.
fHot swap recording:
Cards can be replaced even during recording. This capability allows continuous recording without any interruption since recorded cards can be
successively swapped while recording is continued on another card slot.
fLoop recording:
The unit can retain a certain amount of previously recorded material at all times by successively loop recording data into a specied recording area.
*1 The P2 card driver must be installed. For details on the operating environment required for the P2 card driver, visit the support desk at the following website:
http://pro-av.panasonic.net/
*2 Set the [SLOT SEL] function to the <USER> buttons (<USER MAIN>/<USER1>/<USER2>).
rInstant start and secure data protection
Recording is started instantaneously from a standby state. Since recording is automatically performed to free space on the card, there is no need to cue
up blank area as you do for VTRs. Recording can be started immediately even during a preview simply by pressing the <REC> button. In the Normal
mode, recorded data is never lost by it being overwritten. So, you can be rest assured that your data is safe unless les are deleted or the card is
initialized.
rOther features
fPre-recording:
Critical moments that you might have missed can be recovered. In a standby state, approximately three seconds and approximately seven seconds
of video and audio input to the camera is stored in memory in the HD and SD modes, respectively. This means that video and audio are recorded for
several seconds preceding pressing of the <REC> button.
fOne-shot recording:
This function records for the preset time (single frame to one second) at each press of the <REC> button and is handy for producing animations.
fInterval recording:
In this mode, single frames are recorded at a preset interval (two frames to ten minutes). This allows monitoring and observation, and special effects
to be obtained by ultra-undercrank shooting.
fOne-clip recording:
This function allows multiple recordings into a combined clip and does not isolate single recording (from recording start to stop). The combined clip can
he handled with ease in transferring or copying, etc. as the clip can be handled as a single thumbnail or as a single clip in editing. Up to 99 recordings
can be combined into a single clip.
fProxy recording (extra-cost option):
By installing the video encoder board (extra-cost option), video recordings in MPEG4 format or H.264 format and real-time metadata such as time
code data can be recorded to the P2 card and SD memory card simultaneously, in addition to the video and audio of the materials recorded on the
camera. This is effective in checking and editing clips.
rClip thumbnail preview
Recordings are made as clips (les) for each cut. A thumbnail image and le information are automatically appended to each clip. When previewing on
the viewnder screen, the clip selected from the thumbnail list display can immediately be played back or the clip data can be checked. This thumbnail
and le information is also displayed on a computer (by P2 Viewer Plus*) or in nonlinear editing software.
* P2 Viewer Plus is viewing software for Windows PCs provided to P2 users by free download.
rShot marks and text memo
Shot marks which, for example, can help you distinguish OK cuts from reject cuts, are assigned to each clip. Shot marks can be added both during and
after a recording. Only marked clips can be displayed when clips are mounted on a computer (by P2 Viewer Plus).
A function for recording text memos is also provided so that empty tag-like text memos can be registered by pressing the <USER> buttons (<USER
MAIN>/<USER1>/<USER2>) assigned with this function at any locations (up to 100) in a clip during recording or preview. Memos can be searched for
later on a computer (P2 Viewer Plus) to write text to.
In addition, by copying clips by text memo block, only the necessary portions can be extracted from a single clip with the camera.

– 14 –
Chapter 1 Overview — Features of recorder/play unit
rSD memory card slot
The camera is provided with the SD memory card slot. Scene les and user setting les can be saved and loaded. Metadata upload les (created on P2
Viewer Plus) containing the name of the camera person or reporter, shooting location, text memos or other information can be read to the SD memory
card or read as clip metadata.
rHD/SD SDI output and down converter
Video output lines (BNC x2) are provided as standard. This enables exible support of monitor or line recording. A built-in down converter is also
provided to allow the aspect mode to be selected. Composite output is also supported.
rHDMI output
Video can be output to a monitor compatible with the <HDMI> terminal.
fThe camera is not compatible with VIERA Link.
rHD/SD SDI input (extra-cost option):
By installing the HD/SD SDI input board (extra-cost option), SDI signals input from the <SDI OUT/IN (OP)> terminal can be recorded.
Note, however, that only SDI signals in the same recording format as the camera can be recorded.
rControl for ne-adjustment of audio recording level
A control for ne-adjusting the audio recording level is provided on the front of the camera. This is particularly useful for adjusting the audio level when
you are taking photos alone. This control can also be disabled.
rSupport for built-in UniSlot wireless receiver
The camera is designed to support an optional slot-in wireless receiver. (page 96)
It also supports 2-channel wireless receivers.

– 15 –
Chapter 1 Overview — How to use the camera
How to use the camera
The camera records to P2 cards. These large-capacity P2 cards feature outstanding transfer speeds to enable HD recording, smooth editing and
dubbing.
Editing, saving using external equipment
'DWDILOHVIRUSHUIRUPLQJQRQOLQHDUHGLWLQJRQDFRPSXWHUDUH
WUDQVIHUUHG
7KHFDPHUDGLUHFWO\FRQWUROVWKHKDUGGLVNGULYHWRWUDQVIHUGDWD
9LDWKH86%!WHUPLQDO
&RQQHFWLRQWRH[WHUQDOHTXLSPHQWLQ86%GHYLFHPRGH
3FDUG3HUVRQDOFRPSXWHU
86%GHYLFHPRGH
9LDWKH86%!WHUPLQDO
&RQQHFWLRQWRH[WHUQDOHTXLSPHQWLQ86%KRVWPRGH
([WHUQDOKDUGGLVNGULYH
86%KRVWPRGH
%1&FDEOHFRPSRVLWH6',
+'0,FDEOH
$XGLRSLQFDEOH
9LGHR
HTXLSPHQWPRQLWRU
*1 P2 cards and cables are optionally available. They are not supplied with the camera.
*2 The USB 2.0 cable is not supplied with the camera. Prepare a commercial USB 2.0 cable (double-shielded for noise suppression).
*3 For the BNC cable (optional) connected to the <SDI OUT/IN (OP)> and <MON OUT> terminals, prepare a double-shielded cable equivalent to 5C-FB.
*4 Prepare the HDMI cable (optional) with double or more shielded. For the HDMI cable, use of the Panasonic HDMI cable is recommended.

– 16 –
Chapter 1 Overview — System conguration
System conguration
+'YLHZILQGHU
$*&9)*
$*&9)*
$-+9).*
6RIWFDUU\LQJFDVH
$-6&
+DUGFDUU\LQJFDVH
$-+7*
6KRWJXQPLFURSKRQH
3KDQWRP9
$*0&*
8SJUDGH6RIWZDUH.H\
$*6)8*
1HWZRUNIXQFWLRQH[WUDFRVWRSWLRQ
8SJUDGH6RIWZDUH.H\
$*6)8*
3URGXFWLRQSDFNH[WUDFRVWRSWLRQ
8SJUDGH6RIWZDUH.H\
$*6)8*
83/,1.GHYLFHFRQWUROIXQFWLRQH[WUDFRVWRSWLRQ
8SJUDGH6RIWZDUH.H\
$*6)8*
3OD\OLVWHGLWIXQFWLRQH[WUDFRVWRSWLRQ
6'PHPRU\FDUG
3PHPRU\FDUG
PLFUR3PHPRU\FDUG
86%FRPSOLDQWGHYLFH
8QL6ORWZLUHOHVVPLFURSKRQHUHFHLYHU
$*+3;3
$*+3;(-
5DLQFRYHU
5HPRWHFRQWUROXQLW
6+$15&
$-5&*
5HPRWHFRQWUROFDEOH
$-&*
([WHQVLRQFRQWUROXQLW
$*(&*
%DWWHU\
+<7521
',21,&+&
([WHUQDO'&SRZHUVXSSO\
/&'PRQLWRU
%7/+:
%7/+HWF
:LUHOHVVPRGXOH
$-:0
9LGHRHQFRGHUERDUG
$*<';*
+'6'6',LQSXWERDUG
$*<$*
/HQV
%D\RQHWW\SH
)8-,121&$121
7ULSRGDGDSWRU
6+$170
9PRXQWW\SH
EDWWHU\SODWH
(1'85$(
(1'85$(

– 17 –
Chapter 1 Overview — System conguration
*1 A battery holder is provided as standard on the main unit.
*2 For the latest information on P2 cards and SD memory cards not available in the Operating Instructions, visit the support desk at the following website:
http://pro-av.panasonic.net/
*3 Refer to the operating guide of “AJ-RC10G for AG-HPX600/610 series (AG-HPX600P/HPX610P/HPX600EJ/HPX610EJ/HPX600EN)” at the following website:
http://pro-av.panasonic.net/en/manual/index.html
*4 To use the wireless LAN function for the network function, the wireless module AJ-WM30 is required. To use the streaming function of the network function, the
video encoder board AG-YDX600G is required.
*5 To use, insert it into the microP2 card adaptor AJ-P2AD1G (optional). For details, refer to the operating instructions of “microP2 Card Compatible” at
the following website: Descriptions for AG-HPX600P/AG-HPX600EJ/AG-HPX600EN in the operating instructions are also applied to AG-HPX610P/
AG-HPX610EJ.
http://pro-av.panasonic.net/en/manual/index.html

– 18 –
Chapter 1 Overview — Accessories
Accessories
Shoulder strap (page 97)
Mount cap (already attached to the product) (page 20)
@@NOTE
tAfter unpacking the product, dispose of the packing material
properly.

This chapter describes the names, functions, and operations of parts on
the camera. Details displayed on the [HOME] screen of SmartUI are also
described.
Chapter 2 Description of Parts

– 20 –
Chapter 2 Description of Parts — Power supply and accessory mounting section
Power supply and accessory mounting section
1
5 6 7 2018171615
2
11 128 13
10
3
4
14
9
19
11
1 <POWER> switch (page 35)
Used to turn on/off the power.
2 Battery release lever (page 88)
Pull this battery release lever down to release the battery.
3 Battery holder (page 88)
Mount the Anton/Bauer battery.
4 Light control switch (page 88)
5 <DC IN> terminal (page 89)
This is the input terminal for the external power supply. Connect to the
external DC power supply.
6 <DC OUT> (DC power supply) output terminal (page 99)
This is the DC 12 V output terminal. It provides a maximum current of
1.5 A.
@@NOTE
tWhen connecting external equipment to this terminal, rst fully
check the polarities of the connection. Failure to do so may
result in a malfunction.
7 <REMOTE> terminal (page 152) (page 151)
Connect the remote control unit AJ-RC10G (optional) to remote-
control some functions.
Connect the extension control unit AG-EC4G (optional) to remote-
control some functions.
8 Light output terminal
Connect the Anton/Bauer Ultralight 2 (optional) or an equivalent
product of 50 W or under for the video light.
The battery charge level drops sharply when the light is illuminated.
When using the light, using a battery of 90 Wh or more is
recommended.
9 Cable holders
Used for clamping the light and microphone cables in place.
10 Accessory mounting holes
Attach accessories. Do not use for purposes other than attaching
accessories.
fMounting hole size
-1/4-20 UNC (screw length 10 mm or shorter)
-3/8-16 UNC (screw length 10 mm or shorter)
11 Shoulder strap ttings (page 97)
Attach the shoulder strap.
12 Light shoe
Attach the video light.
fMounting hole size
1/4-20 UNC (screw length 6 mm or shorter)
13 Viewnder left/right positioning ring
To adjust the left/right position of the viewnder, loosen this ring,
and slide the viewnder to the left or right to adjust it to an easy-to-
view position. Tighten the ring to clamp the viewnder in place after
adjusting the viewnder.
14 <VF> terminal
Mount the viewnder AG-CVF10G (optional).
15 Lens cable/microphone cable clamp (page 91)
This clamp secures the lens and microphone cables.
16 <LENS> terminal (page 91)
Connect the lens connection cable. For a detailed description of the
lens used, refer to the Operating Instructions for the lens.
17 Tripod mount (page 97)
Attach the optional tripod adaptor (SHAN-TM700) when mounting the
camera on the tripod.
18 Lens mount (2/3-type bayonet) (page 91)
Mount the lens.
19 Lens lever (page 91)
After mounting the lens to the lens mount, tighten the lever to secure
the lens.
20 Mount cap (page 91)
Raise the lens lever to remove the cap. Replace the cap when the
lens is not mounted.