Panasonic CQ-C7353N User manual

© 2007 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and distribu-
tion is a violation of law.
ORDER NO. ACED070209C3
AUTOMOTIVE AFTERMARKET
CQ-C7353N
WMA MP3 CD Player/Receiver
TABLE OF CONTENTS PAGE PAGE
1 Service Navigation----------------------------------------------- 2
2 Specifications ----------------------------------------------------- 3
3 Features ------------------------------------------------------------- 4
4 Technical Descriptions----------------------------------------- 5
5 Disassembly and Assembly Instructions ---------------10
6 Block Diagram----------------------------------------------------13
7 Wiring Connection Diagram ---------------------------------16
8 Schematic Diagram---------------------------------------------17
9 Printed Circuit Board-------------------------------------------21
10 Exploded View and Replacement Parts List -----------26
11 Schematic Diagram for Printing with A4 Size----------37

2
1 Service Navigation
1.1. About Lead Free Solder (PbF)
Distinction of PbF PCB :
• PCBs (manufactured) using lead free solder will have a PbF
stamp on the PCB.
Caution :
• Pb free solder has a higher melting point than standard sol-
der; Typically the melting point is 50 - 70°F (30 - 40°C)
higher. Please use a soldering iron with temperature control
and adjust it to 700 ± 20°F (370 ± 10°C). In case of using
high temperature soldering iron, please be careful not to
heat too long.
• Pb free solder will tend to splash when heated too high
(about 1100°F/600°C)
• This lead free solder will be used for the products after serial
No. 1,000,001.
1.2. Laser Products
1.3. Replacing the Fuse
Use fuses of the same specified rating 15 amps. Using different
substitutes or fuses with higher ratings, or connecting the unit
directly without a fuse, could cause fire or damage to the stereo
unit.
1.4. Maintenance
Your product is designed and manufactured to ensure a mini-
mum of maintenance. Use a dry, a soft cloth for routine exterior
cleaning. Never use benzine, thinner or other solvents.
1.5. Notes
[RADIO BLOCK]
Do not align the AM/FM package block. When the package
block is necessary, it will be supplied already aligned at the fac-
tory.
[CD DECK BLOCK]
This model has no servo alignment points because microcom-
puter controls the servo circuit.

3
2 Specifications
2.1. Specifications*
2.2. Dimensions
General
Power Supply DC 12V (11V - 16V)
Test Voltage 14.4V
Negative Ground
Tone Controls(Bass/Treble) Bass: ±12dB at 60 Hz
Treble: ±12 dB at 16kHz
Equalizer Center Frequency 60, 160, 400, 1 k, 3 k, 6 k, 16 kHz
Variable Range of Equalizer -12 dB to 12 dB (2 dB step)
Current Consumption Less than 2.2A (CD mode, 0.5W 4
Speaker)
Maximum Power Output 50 W x 4 (at 1kH)
Power Output 23 W x 4 (DIN 45 324, at 4Ω)
Speaker Impedance 4 - 8 Ω
Pre-amp Output Voltage 2.5 V (CD mode: 1 kHz, 0 dB)
Subwoofer-output voltage 2.5 V (CD mode, 1 kHz, 0 dB)
Pre-amp Output Impedance 200 Ω
Subwoofer-output impedance 200 Ω
Dimensions (W×H×D)** 178×50×155mm
Weight** 1.6 kg
CD Player
Sampling Frequency 8 times Oversampling
DA Converter 4 DAC System
Pick-Up Type Astigma 3-beam
Light Source Semiconductor Laser
Wave Length 790 nm
Frequency Response 20 Hz - 20 kHz (±1 dB)
Signal to Noise Ratio 96 dB
Total Harmonic Distortion 0.01 % (1 kHz)
Wow and Flutter Below Measurable Limits
Channel Separation 85 dB
FM Stereo Radio
Frequency Range 87.5 MHz - 108 MHz
Usable Sensitivity 6dB/µV (S/N 30 dB)
Stereo Separation 35 dB (at 1 kHz)
AM (MW) Radio
Frequency Range 531 kHz - 1602 kHz
Usable Sensitivity 28 dB/µV (S/N 20 dB)
AM (LW) Radio
Frequency Range 153 kHz - 279 kHz
Usable Sensitivity 32 dB/µV (S/N 20 dB)
* Specifications and the design are subject to possible modification
without notice due to improvements.
** Dimensions and Weight shown are approximate.
*** Above specifications comply with EIA standards.

4
3 Features
• Hands Free Phone System. (The optional Bluetooth hands-
free kit: CY-BT100N)
• Expansion Module (The optional Hub unit: CY-EM100N)
• The optional adapter allows you to connect the optional
Panasonic DVD changer unit (CX-DH801N).
• The optional adapter allows you to connect the optional
Panasonic CD changer unit (CX-DP880).
• The optional adapter allows you to connect the optional
iPod® series.
• SQ7 (7-Band Sound Quality).
• Customize the Display (Customize Function)
• MP3/WMA Playback from CD-R/RW.

5
4 Technical Descriptions
4.1. Terminals Description
4.1.1. Main Block
IC601 ：C2CBKG000037
Pin
No. Port Description I/O (V)
FM AM CD
1 PANEL OPEN Panel open detection I 0 5.2 5.2
2 PANEL CLOSE Panel close detection I 0 0 5.2
3 SUBM CNT 3.3V power control for Dis-
play O5 - -
4 BATT Battery power check I 4.8 5 5
5 ACC Acc. power check I 4.8 5 5
6 SDA Serial data for electronic
volume I/O 4.9 4.9 4.9
7 SCLK Serial clock for electronic
volume O4.94.94.9
8 CD MUTE Signal mute from CD deck I 5 5 5
9 Vss GND - 0 0 0
10 ST FM stereo detection I 5.1 5.2 5.2
11 PLL DI Serial data to PLL O 0.6 0 0
12 PLL DO Serial data from PLL I 5.2 5.2 5.2
13 PLL CLK Serial clock for PLL O 4.9 4.9 4.9
14 PLL CE Chip enable for PLL O 0 0 0
15 CD RESET Reset for CD deck O 4.9 4.9 4.9
16 SUB SI Serial data to Display CPU O 0.6 0.6 0.8
17 CD IN Disc-in detection I 5 5 5
18 SUB SO Serial data from Display
CPU I4.44.44.4
19 UP SO XM SO/UP SO Serial data
from Changer I1.61.61.6
20 UP CLK Serial clock for Changer or
Flash writer I4.94.94.9
21 Vdd +5V power supply - 4.9 4.9 4.9
22 XM SI (MO)/ UP
SI Serial data to Satellite or Flash writer O0 0 0
23 CD SI Serial data to CD deck O 0 0 0
24 CD SCLK Serial clock for CD deck I/O 0 0.4 0
25 CONDENSOR Capacitor connection for
power -3.33.33.3
26 CD DO Serial data from CD deck I 0 0 0
27 CH STB Strobe from Changer I 0 0 0
28 CH REM Remote control codes to
Changer O4.94.90.4
29 DECK V CONT Power control for CD deck O 4.9 4.9 4.9
30 REMO INT Interrupt for remote control I 3.7 3.7 3.7
31 CD FS Frame sync. for CD deck O - - -
32 Avdd +5V power supply - 5.1 5.1 5.1
33 AVREF +5V power supply - 5.1 5.1 5.1
34 AVGND GND - 0 0 0
35 AVSS GND - 0 0 0
36 SD FM/AM signal level meter I 0.2 0 0.3
37 INIT A Model setting A by voltage
level I000
38 INIT B Model setting B by voltage
level I000
39 A IN Spectrum analyzer data I 0 0 0
40 Vss GND - 0 0 0
41 SYS ID1 Hub connection device
detection ID 1 I000
42 SYS ID2 Hub connection device
detection ID 2 I5.25.25.2
43 EVENT Bluetooth incoming detec-
tion I5.25.25.2
44 HUB CNT Request of hub connection
check O0 0 0
45 CD SW1 Disc detection switch 1 I 0 0 0
46 CD SW2 Disc detection switch 2 I 0 0 0
47 MOD0 Operating mode control 0
from Flash writer I 5.1 5.1 5.1
48 MOD1 Operating mode control 1:
pulled up to H - 5.1 5.1 5.1
49 MOD2 Operating mode control 2
from Flash writer I000
50 H STANDBY Standby control from exter-
nal I555
51 NC Not connected - - - -
52 FP MOTOR1 Open/Close of Front panel
1O 4.9 5 4.9
53 FP MOTOR2 Open/Close of Front panel
2O 4.9 5 4.9
54 V CONT1 Reference voltage control
for motor driver O0 0 5
55 REMO 1 Remote control data I 5 5 5
56 SA CLK Spectrum analyzer clock O 5 5 4.9
57 EXT MUTE Pulled up to H I 5.3 5.2 5.2
58 AMP CONT Power control for external
Amplifier O 4.9 5 4.9
59 BZ OUT Buzzer signal O 0 0 0
60 OEL VCONT Power control for OEL O 0 0 0
61 WOW MODE1 SRS WOW mode 1 O 0 0 0
62 WOW MODE2 SRS WOW mode 2 O 0 0 0
63 WOW MODE3 SRS WOW mode 3 O 0 0 0
64 DIM1(NC) Not connected - - - -
65 DIM2(NC) Not connected - - - -
66 MAIN CNT2 Power control for Hub O 5 5 5
67 SRC KEY SOURCE key detection I 5 4.9 5
68 PANEL IN Panel attachment detection I - - -
69 RDS CLK RDS clock input IN
T2.6 0 2.6
70 NC Not connected - - - -
71 RDS DATA RDS data input I 2.6 0.2 2.9
72 MAIN CONT Main power control O 4.9 4.9 4.9
73 INV CONT Dimmer power control O 5 5 5
74 AF MUTE Audio mute O 5 5 5
75 RESET Reset I 5 5 5
76 ELEV Focus elevation for SRS
WOW O- - -
77 X1A Oscillator clock O 2.1 2.1 2.1
78 X0A Oscillator clock I 1.6 1.6 1.6
79 Vss GND - 0 0 0
80 X1 Crystal oscillator clock I 2 2 2
81 X2 Crystal oscillator clock O 2.5 2.5 2.5
82 Vdd +5V power supply - 5 5 5
83 P00 Pulled down to L - 0 0 0
84 P01 Pulled up to H - 5.1 5 5.1
85 OFFSET DET Audio clipping level detec-
tion from Power amp. I000
86 STBY Standby for Power amp. O 5 5 5
87 AMP MUTE Mute for Power amp. O 0 0 0
88 ILL SENS Pulled up to H - 5 5 5
89 NC Not connected - - - -
90 EP DO EPROM comuni. data input O/I 0 0 0
91 NC Not connected - - - -
92 NC Not connected - - - -
93 SUB RESET Reset for display CPU O 4.9 5 4.9
94 DISPM CONT 5V power control for Dis-
play O0 0 0
95 NC Not connected - - - -
96 NC Not connected - - - -
97 NC Not connected - - - -
98 S LED Security LED drive O 0 0 5
Pin
No. Port Description I/O (V)
FM AM CD

6
4.1.2. Display Block
IC900 ：C2CBYY000150
4.1.3. CD Servo Block
IC101 ：YESAM337
99 ANT CONT Power control for antenna
motor O5.25.25.2
100 EP CS(NC) Not connected - - - -
Pin
No. Port Part Name & Description I/O (V)
1 A18 A18 in Address bus O 1.5
2 A19 A19 in Address bus O 1.7
3 A20 A20 in Address bus O 1.3
4 NC Not connected - -
5LEDG - - -
6LEDB - - -
7 A0 A0 in address bus for LCD O 1.3
8 A1 A1 in Address bus O 0.3
9VSS GND - -
10 A2 A2 in Address bus O 0.4
11 A3 A3 in Address bus O 0.4
12 A4 A4 in Address bus O 0.4
13 A5 A5 in Address bus O 1.3
14 A6 A6 in Address bus O 0.4
15 A7 A7 in Address bus O 0
16 A8 A8 in Address bus O 1.3
17 A9 A9 in Address bus O 0
18 A10 A10 in Address bus O 0
19 A11 A11 in Address bus O 1.5
20 A12 A12 in Address bus O 1.7
21 VCC +3.3V Power supply - 3.5
22 A13 A13 in Address bus O 1.4
23 A14 A14 in Address bus O 1.5
24 A15 A15 in Address bus O 1.7
25 SIN0 Serial data from Main CPU or
Flash writer I0.5
26 SOT0 Serial data to Main CPU or
Flash writer O1.8
27 SCK0 Serial clock for Flash writer I 3.5
28 NC Not connected - -
29 FRASH RESET Reset for Flash memory O 3.5
30 KS1 Key scan 1 O 0
31 NC Not connected - -
32 NC Not connected - -
33 AVCC +3.3V Power supply - 3.5
34 AVRH +3.3V Power supply - 3.5
35 AVSS/AVRL GND - -
36 TH DETECT Pulled up to H - 1.3
37 KS2 Key scan 2 O 0
38 KS3 Key scan 3 O 0
39 NC Not connected - -
40 VSS GND - -
41 KI5 Key-in return 5 I 0
42 KI4 Key-in return 4 I 0
43 KI3 Key-in return 3 I 0
44 KI2 Key-in return 2 I 0
45 NC Pulled down to L - 0
46 NC Pulled up to H - 3.5
47 MD0 Operating mode control 0 from
Flash writer I3.5
48 MD1 Operating mode control 1:
pulled up to H -3.5
49 MD2 Operating mode control 2 from
Flash writer I0
50 NC Not connected - -
51 ROTARY 1 Volume-up detection from
Rotary encoder I2.5
Pin
No. Port Description I/O (V)
FM AM CD 52 ROTARY 2 Volume-down detection from
Rotary encoder I2.5
53 NC Not connected - -
54 NC Not connected - -
55 NC Not connected - -
56 NC Not connected - -
57 NC Not connected - -
58 FLASH CE Chip enable for Flash memory O 3.4
59 LCD CS LCD chip select O 3.4
60 LED R
61 NC Not connected - -
62 NC Not connected - -
63 NC Not connected - -
64 VLCD CONT Power control for LCD O 3.4
65 NC Not connected - -
66 NC Not connected - -
67 NC Not connected - -
68 NC Not connected - -
69 OE/RD Output enable for Flash mem-
ory or Read strobe for LCD O3.4
70 LCD WR Write strobe for LCD O 3.4
71 FLASH WE Write enable for Flash memory O 3.4
72 NC Not connected - -
73 LCD RESET Reset for LCD O 3.4
74 FLASH RY/BY Ready/Busy from Flash mem-
ory I3.4
75 RST Reset I 3.5
76 NC Not connected - -
77 NC Not connected - -
78 X0A GND - -
79 VSS GND - -
80 X0 System clock (12.5MHz) I 1.3
81 X1 System clock (12.5MHz) O 1.5
82 VCC +3.3V Power supply - 3.5
83 D0 D0 in Data bus I/O 0.9
84 D1 D0 in Data bus I/O 0.9
85 D2 D0 in Data bus I/O 1.1
86 D3 D0 in Data bus I/O 0.9
87 D4 D0 in Data bus I/O 1
88 D5 D0 in Data bus I/O 1.1
89 D6 D0 in Data bus I/O 1.1
90 D7 D0 in Data bus I/O 0.9
91 D8 D0 in Data bus I/O 0.9
92 D9 D0 in Data bus I/O 0.9
93 D10 D0 in Data bus I/O 0.9
94 D11 D0 in Data bus I/O 0.5
95 D12 D0 in Data bus I/O 0.9
96 D13 D0 in Data bus I/O 0.7
97 D14 D0 in Data bus I/O 0.7
98 D15 D0 in Data bus I/O 0.7
99 A16 A16 in Address bus O 3
100 A17 A17 in Address bus O 1.7
Pin
No. Port Descriptions I/O (V)
1AVSS GND - 0
2 LD-MT Loading Motor drive IC control 1 O 3.2
3 CNT Loading Motor drive IC control 2 O 3.2
4 - Not Connected - -
5 LD-EJ Loading Motor drive IC control
(Eject) O0
6 AMUTE Mute signal output O 0
Pin
No. Port Part Name & Description I/O (V)

7
7 - Not Connected - -
8 SBSY DSP IC SBSY O 0
9 - Not Connected - -
10 - Not Connected - -
11 TXD0 Serial data output O 0
12 RXD0 Serial data input I 0
13 CLK0 Clock input I 2.9
14 TXD1 Serial data output O 3.2
15 RXD1 Serial data input I 0
16 CLK1 Clock input I 0
17 AMD - - 3.2
18 DVCC Power supply (3.3V) - 3.2
19 X2 Crystal oscillator - 1.3
20 DVSS GND - 0
21 X1 Crystal oscillator - 1.3
22 AMI - - 3.2
23 RESET Reset I 3
24 - Not Connected - -
25 - Not Connected - -
26 NMI - - 3.2
27 - Not Connected - -
28 STBY DSP IC STBY O 0
29 RST DSP IC RST O 3.2
30 CCE DSP IC CCE O 2.6
31 BUCK DSP IC CK O 2.8
32 BUS3 DSP IC BUS3 O 2.8
33 BUS2 DSP IC BUS2 O 2.8
34 BUS1 DSP IC BUS1 O 2.8
35 BUS0 DSP IC BUS0 O 2.9
36 RESET SW Mechanics deck REST SW input I 3.2
37 SW1 Mechanics deck SW1 input I 0
38 SW2 Mechanics deck SW2 input I 0
39 CONT (P13) DSP IC power control 1 O 3.2
40 - Not Connected - -
41 - Not Connected - -
42 - Not Connected - -
43 CONT (P17) DSP IC power control 2 O 3.2
44 PIO0 DSP IC PIO0 O 0
45 ZDET LOAD detect I 0
46-49 - Not Connected - -
50 - - - 3.2
51-58 - Not Connected - -
59 CDFS Serial frame sink signal input (CD
ON) I2.3
60 P50/AN0 Reference voltage I 0.3
61 P51/AN0 Loading motor detect I 2.1
62 P52/AN2 - - 0
63 P53/AN3 - - 0
64 AVCC Power supply (3.3V) - 3.2
Pin
No. Port Descriptions I/O (V)

8
4.2. IC Block Diagram
4.2.1. Main Block
IC201 : C1BB00000796
IC231 : C0JBZS000003
IC670 : YEAMC14584BE
IC730 : C0DAEKG00002
IC701 : C0DAZHF00004
IC755 : C0DBZGD00040

9
IC760 : C0GBG0000032
4.3. Display Block
IC902 : C0EBF0000374
4.4. CD Servo Block
IC401, IC403 : YESAM341
IC402 : YESAM342

10
5 Disassembly and Assembly Instructions
5.1. How to Remove the Flexible PCB(AP2)
CN601
AP2
How to remove the flexible PCB(AP2)
1. Remove the trim plate.
2. Remove the removable face plate unit by
pressing the release button.
3. Remove the screw( ) and take off the Upper cover.
4. Remove the 3 screws( ) and take off the CD
deck.
5. Remove the flexible PCB(AP2) from the CN601
(E-3108a).
6. Remove the screw( ) from the Drive Mechanis
m
Ass'y and remove the flexible PCB case.
7. Remove the flexible PCB(AP2) from the CN1.
Trim plate
Release button
Upper cover
CD deck
Drive Mechanism
Ass'y
Flexible PCB case
CN1
AP2
Removable
face plate unit

11
5.2. How to Install the Main P.C.B of the Electric Display

12

13
6 Block Diagram
6.1. Main-1 Block
AM
ANT
FM
ANT
ANT51
CN351 E-3108a(1/2)
AUX
RL
17
26
20 1714 12
24524 31
9 15 8 16 17
14
FM/AM OSC
FM IF
VSM
SD(ST)
MODE
FM/AM
VT
EOFM
R-CH
CDC L
L-CH
Q56
R-CH
12
13
PA51
FM/AM TUNER
Q411
IC401
PLL
XL401
7.2MHz
Q55
7
6
56
39
12
11
17
15
31
24
23
26
45
46
29
72
99
5
86
87
85
74
59
76
63
62
61
8
13
14
36
10
AUDIO9V
SCLK
SDA
SA CLK
A IN
PLL DO
PLL CLK
PLL CE
SD
ST
PLL DI
IC601(1/2)
CPU
16 14 12 13 31
33
29 28 27 40
43
44
42
4
40
INPUT
SEL LOUD/
VOLUME/
EQ
SW
SPECTRUM
ANALIZER
SW
SW
REG
SW
SUB
WOOFER
REAR
MAIN
IC201
ELECTRONIC VOLUME
FADER
FADER
FADER
FADER MIX
25
32
24
17
CD-L
CD-R
CD8V
CD3.3V
CD IN
CD FS
CD SCK
CD SI
CD SO
CD RST
MUTE
CN651
R-CH
IC752
Q650
IC650
CD8V
BATT 5V
REG
LEVEL
SHIFT
16
17
9
10
13
14
4
3
6
5
7
8
1
2
To
C
D DECK
CD SW1
CD SW2
Q652
Q651
Q320
IC231
Q371
Q701
REG
11
6
7
8
3
4
2
5
10
12
14
BATT
VDD5V
ACC
IC701
POWER SUPPLY ANT+B
CD8V
AUDIO9V
SW5V
ILM10V
ACC
DECK V
CONT
ANT CONT
1
MAIN CONT
IC271
POWER AMP
2522 4
5
3
620
23
21
14
12
CLIP
MUTE
STBY
Q346 CN255
CN302
CN202
MUTE
Q335
MUTE
Q341
MUTE R-CH
RL
FL
SW
R-CH
R-CH
R-CH
R-CH
R-CH
1
4
1
4
1
4
L
R
L
R
L
R
REAR
FRON
T
SUB.W
BATT ACC
CN701(1/2)
RL+
RL-
RR+
RR-
FL+
FL-
FR+
FR-
BATT 12
34
56
78
910
1112
1314
1516
Q372
Q680 Q681
Q376
85 87 86
ELEV
CONT
MODE1
MODE2
MODE3
ELEV
BZ OUT
AF MUTE
AMP MUTE
VOFF DET
STBY
L
OUT L IN
RL
FL
SW
IC221
SRS WOW
AUDIO
TRU
BASS
FOCUS
3D
STEREO
CQ-C7353N MAIN-1

14
6.2. Main-2/Display Block
M
SW5V
CN901
INV 10V
REMO
OUT
14
16
3
5
6
7
10
9
8
VLCD10V
SUB RST
Q902,903
IC903
POWER
SW
RESET
IR
RECEIVE
VDD3.3V
SO
SI
VLCD
CONT 64 73
59
70
7
69
83-98
25
26
12 75
58
71
74
29
26
11
15
12
80
81
27
47
49
SK
MD0
MD2
51
52
36
IC900
DISPLAY
CONTROL
1-3,8
10-20,
22-24,
99,100
41–44
30,37,38
SW914
VOL UP
VOL DOWN
SW901
ROTARY
ENCODER
SW901-903
905-913 KS1-3
KI2-5
TH DETECT
KEY-IN
MATRIX
XL900
CE
WE
RY/BY
(CN903)
FLASH RESET
A1-20 1-9
16-25,48
IC901
FLASH
MEMORY
29-36
38-45 28
OE
OE/RD RD
D0-7D0-15
LCD RESET
CS
WR
A0
V OUT
VDD3.3V VDD
VDD
CN902
13
VDD3.3V 4
2
3
7
8
6
1
24
12
29
28
27
15
22
25
26
–
2
1
1
(CN904) CP904
REG
E-9782a E-9782b
LCD90
1
PWR/SRC
SO
SI
RESET
PANEL IN
SUB SI
SUB SO
2
1
21
2
Q912
D951,952
LED
DRIVE
R/G/B
D933-935
R/G/B
D931,932
RED
GREEN
BLUE
(CN905) CP905
Q941-943
LED B LED G LED R
6560
D907
IC902
RESET
+
12
10
8
1
13
13
11
9
2
2
5
6
4
1
9810 7
5463
12 11
3
IC670
CN680
4
1
3
2
8
6
7
MOTOR
DRIVE
17 16
OUT1
OUT2
IC760
9
5
21
18
20
VR
Q760
VOLT
CONT
CN760
1
2
BATT ILM10V
V CONT1
SYS ID1
SYS ID2
MAIN CONT2
CH REM
HUB CNT
EVENT
CH STB
CH CLK
CH DATA
SO
MOD2
MOD0
RST
SI
CLK
AMP CONT
FP MOTOR1
FP MOTOR2
54
77
78
22
20
27
28
44
43
19
58
57
4
75
50
47
49
41
42
66
52
53
Vcc
D630
Q630
S LED
1
2
81
80
67
3
94
98
60
73
55
30
68
CN701(2/2)
ANT CONT
T/N MUTE
AMP CONT POWER
SW
Q791,793
ANT+B
BATT
BATT
BATT
5V
CN600
1
3
2
4
5
7
6
8
9
11
10
12
13
15
14
16
DISP M CONT
5V
5V
SUB M CONT
IC630
IC755
REG
POWER
SW
Q633
PANEL IN
REMO IN
REG
INV 10V
BATTINV10V
INV CONT
IC730
CN601
4
2
13
11
9
12
8
6
7
13
10
SUB SI
SUB SO
SRC KEY
18
16
93 SUB RST
XL601
3.685MHz
PANEL OPEN
PANEL CLOSE
SW601
SW602
E-3108a(2/2)
IC601(2/2)
CPU
CQ-C7353N MAIN-2/ DISPLAY
LEVEL
SHIFT
IC702
BATT CHECK,RESET
45
1
BATT
RESET
IC790
ACC REG
CDC L
R-CH
XL602
32.768KHz
REMO I
REMO INT

15
6.3. CD Servo Block
M
M
14
13
12
11
18
17
16
15
OPTICAL PICK-UP
A
B
E
F
PD LPD
LD LD LD
DRIVE
DSP3.3V
CD3.3V
IC403
IC402
IC401
DSP1.5V
1
I-V
AMP
7
9
3
2
4
15
16
13
14
11
T+
T-
F+
F-
FOCUS
COIL
TRACKING
COIL
SPINDLE
MOTOR
SLED
MOTOR
SP-
SP+
SL-
SL+
IC301
PICK-UP DRIVE
2
3
23
26
24
20
9
28
27 42
9
10
12
SLED
MOTER
DRIVE
SPINDLE
MOTER
DRIVE
TRACKING
COIL
DRIVE
FOCUS
COIL
DRIVE
MUTE
MUTE
RST
43 37
38
36
39
5
29
2
3
SW1
SW2
RESET
TVD
ESC
FOD
TE
FE
RF
TRD SERVO
CTL
IC201 RF AMP,SERVO,DSP
92
91
99
98
97
95 EFM
DEM
REG CD8VDSP3.3V REG
CD3.3V
1.5V
REG
ADC
15
18
14
9
24
23
18
36
I
39
32
I
35
34
40
41
43
BUCK
ZDET
BUS 0 - 3
CCE
STBY
14
53
SBSY
X201
VCOM
LD EJ
RST
LD MT
CNT
XI
XO
CN101
CN102
Lch
Rch
CD3.3V
DC8V
10 DC8V
8
12 CD SI
7
11 CD SO To
MAIN
CN65
1
1SW1
2SW2
6
13 CD SCK
5
59 CD ON
4
6CD MUTE
3
23 CD RST
3.3V
8V
IC101
CPU
19
21 X1
X2
X101
3032-14-35
Q201
CQ-C7353N CD Deck Block
30 Lch
Rch
DAC MUTE
Q203,204
Q202
13
27
31
30
28
8
44
45

16
7 Wiring Connection Diagram
Extension
Connector
Jig Part No.
YESFZS2051
Extension
Connector
Jig Part No.
YESFZS2061
Power
Connector
Amp-Relay Control Power
Speaker
8/
External Remote Control
External Mute
RL+ RL-
FL+ FL-
FR+ FR-
ACC GND
Motor
ANT
BATT
ACC
BATT
GND
Not Used
Motor ANT CN302
CN202
CN255
CN351 L
R
L
R
L
R
L
R
<PRE-OUT REAR>
<S.W. OUT>
<AUX1-IN>
<PRE-OUT FRONT>
CN701 CP670
(CN255) (CN351)(CN302)(CN202)
14141414
ANT51
CN651
CN670
17 18
1
18
1
1
7
2
17
2
Loading / Feed
Moter Reset
SW
Optical
Pic-Up
Ass'y
CN101
SW1 SW2
CN102
Spindle
Motor
16
1
CD Servo P.C.B
3032-14-35
Main P.C.B
E-3108a
CN1(16P)
CN601(16P)
CN760
(2P) Drive
Mechanism
Ass'y
AP2
116
(2P)
CN680
Display P.C.B
E-9782a
LED P.C.B
E-9782b
CN901
CN902(30P)
CP904
(2P)
CP905
(2P)
(CN904)
(CN905)
12
15 16
LCD901

17
8 Schematic Diagram
8.1. Main-1 Block

18
8.2. Main-2 Block

19
8.3. Display Block

20
8.4. CD Servo Block
CQ-C7353N CD DECK
To
MAIN
CN65
1
To Optical Pic Up A'ssy
3032-14-35
YESAN086
YESAM343
YESAM339
YESAM341
YESAM341
YESAN116
YESAN116
B1GDCFJJ008 YESAM342
YESAM337
0
0
3.2
3.2 3.2 3.2 3.2 3.2 2.6 2.8 3.0 1.3
1.3
0 0
2.9
0
0
0
0
3.2
3.2
3.2 3.2
0 0
2.1 0.3 2.3
0
3.2
3.2
3.2
2.9
2.8
2.8
0
0
0
0
0.5
2.8
3.3
3.2
8.0
0
3.2
3.2 0
1.5
3.2 0
1.5
3.2
1.6 1.6 1.6
3.2 0 4.4 4.3 4.5 4.2
0
1.6
0
2.2 2.3 1.6 1.6 1.6 1.6 1.6 1.5 1.5 1.7
0 0 0
1.5 1.6
0 0 0
1.6
2.5
1.8
3.1
0
7.9
3.5
4.1 4.0 3.4
0 0
7.9 1.7 1.1 1.4 1.6 3.2
3.2
3.2
8.0
3.3
0
1.6
1.6
0
0
0
0
0
0
0
0
0.7
1.5 0
0 0 0 0 0 0 0 0 1.5 0 0 1.6 1.6 1.6 1.6
1.6
3.3
3.3
3.3
2.9
2.9
2.8
2.8
2.8
1.6
3.3
3.3
1.5
3.2
2.6
1.4 1.6 0.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.8
1.8
1.3
1.3
3.3
3.3
2.5
0.2
1.8
1.8
1.5
1.5
0
0
2.0
2.0
2V/DIV,5ms/DIV
2V/DIV,5ms/DIV
2V/DIV,1ms/DIV
0.5V/DIV,0.1µs/DIV
8V
3.3V 8V
3.3V
CD(L,R)
The following symbols are
shown on the schematic diagram.
8V
8V
3.3V
8V
L
L
R
L
R
R
R
L
3.3V
3.3V
3.3V
3.3V
3.3V3.3V
3.3V 3.3V
3.3V
8V8V
8V