Panasonic CQ-RDP102S User manual

ORDERNo. ACED020485C3
AUTOMOTIVE CONSUMERELECTRONICS
CQ-RDP102S
CD Player / Receiver with CD Changer Control
SPECIFICATIONS
Specification*
1

General
Power Supply DC 12V (11V - 16V),
Test Voltage14.4V
NegativeGround
ToneControls Bass ; ±12dB at 100Hz
Treble; ±12dB at 10kHz
Current Consumption Less than2.5A(CD playmode,
0.5W×4ch)
MaximumPower Output 45W×4ch(at 4 )
Power Output 20W×4(DIN45 324, at 4 )
Speaker Impedance 4-8
Pre-AmpOutput Voltage 2V (CD mode)
Pre-AmpOutput Impedance 600
FM StereoRadio
FrequencyRange 87.5- 108MHz
UsableSensitivity 6dB/ V (S/N 30dB)
LW Radio
FrequencyRange 153 - 279kHz
UsableSensitivity 32dB/ V (S/N 20dB)
MWRadio
FrequencyRange 531 - 1,602kHz
UsableSensitivity 28dB/ V (S/N 20dB)
CD Player
Sampling Frequency 8 times oversampling
Pick-UpType Astigma 3-beam
Light Source SemiconductorLaser
Wavelength 780nm
FrequencyResponse 20Hz to20,000Hz (±1dB)
Signal toNoise Ratio 96dB
Dimensions** 178×50×150mm
Weight** 1.4kg
*Specificationsand thedesign are subject topossible
modification without notice duetoimprovements.
** Dimensionsand Weight shownare approximate.
2002 Matsushita Communication Industrial Co., Ltd. All rights
reserved. Unauthorized copying and distribution isaviolation of
law.
2

1. FEATUERS
-PLL (Phase Locked Loop) synthesized tuning.
-18-FM, 6-AMpresets with preset scan
-RDS(RadioData System) reception.
-Digital servo for reliableCD playback.
-Removableface plate.
2. LASER PRODUCTS
3. REPLACEING THE FUSE
Use fuses of the same specifiedrating (15A). Using different substitutes orfuses withhigher
ratings, orconnecting the product directlywithout a fuse, couldcause fire ordamage tothe
stereounit.
4. MAINTENANCE
Yourproducts is designedand manufacturedtoensure a minimumof maintenance. Use a dry, a
soft clothforroutine exteriorcleaning. Neveruse benzine, thinnerorothersolvents.
3

5. NOTES
[RADIO BLOCK]
Donot align the AM/FM package block. Whenthe package block is necessary, it will be supplied
alreadyalignedat the factory.
[CD DECK BLOCK]
This model has no servoalignment points because microcomputercontrols the servocircuit.
6. DIMENSIONS
7. WIRING CONNECTION
4

8. BLOCK DIAGRAM
5

9. TERMINALS DESCRIPTION
6

9.1. MainBlock
IC600 : C2CBHF000217
Pin No. Port Descriptions I/O(V) FM(V) AM(V) CD (V)
1NC (Connecting to ground) - 0 0 0
2 NC (Connecting to ground) - 0 0 0
3 NC (Connecting to ground) - 0 0 0
4AVSS Analog ground - 0 0 0
5AF MUTE AF mute O 5.1 5.1 5.2
6AMP-CNT Power Amp. stand-by O 5.1 5.1 5.2
7AVREF Reference voltage - 5.1 5.1 5.2
8 CD-MISO CD data I 0 0 0
9CD-MOSI CD data O 0 0 2.4
10 CD-SCK CD clock O 0 0 5.1
11 CD.C DATA CD.CH data I 0 0 0
12 NC No connection - - - -
13 CD.C CLK CD.CH data shift clock I 0 0 0
14 REMOUT CD.CH remote cont. O 5.0 5.0 5.0
15 BZOUT Beep output O 0 0 0
16 PLL-MISO Data from PLL I 5.1 5.1 5.1
17 PLL-MOSI Data for PLL O 0 0 0
18 PLL-CLK Clock for PLL O 5.1 5.1 5.2
19 PLL-CE PLL chip enable O 0 0 0
20 NC No connection - - - -
21 NC No connection - - - -
22 NC No connection - - - -
23 NC No connection - - - -
24 CD-STB CD strobe O 0 0 5.1
25 CD-A0 CD address 0 O 0 0 4.4
26 CD-RST CD reset O 0 0 5.1
27 CD-RFOK CD RFOK signal I 0 0 5.0
28 CD-LOCK CD lock signal I 0 0 5.0
29 CD-LIMIT CD limitsw I 0 0 5.1
30 CD-SW2 CD SW2 I 5.1 5.1 0
31 NC No connection - - - -
32 NC No connection - - - -
33 Vss Ground - 0 0 0
34 S.LED SecurityLED on/off O 0 0 0
35 ST-IND FMstereo detection I 5.0 5.1 5.1
36 IC2-CLK Electronicvolumeclock O 5.1 5.1 5.2
37 IC2-DATA Electronicvolumedata I/O 5.1 0 5.2
38 NC No connection - - - -
39 NC No connection - - - -
40 NC No connection - - - -
41 LCD-MOSI LCD data output O 0 0 0
42 LCD-MISO LCD data input I 5.0 5.0 5.0
43 LCD-CLK LCD clock O 0 0 0
44 LCD-CE LCD chip enableoutput O 0 0 0
45 POWER LED Pilotlamp on O 0 0 0
46 ANT.CONT Motor antennacontrol O 5.1 5.1 0
47 NC No connection - - - -
48 NC No connection - - - -
49 REM-IN_SUB Remote control sig. sampling I 0 4.4 4.4
50 NC No connection - - - -
7

Pin No. Port Descriptions I/O(V) FM(V) AM(V) CD (V)
51 NC No connection - - - -
52 NC No connection - - - -
53 NC No connection - - - -
54 TEL-MUTE Notused - - - -
55 PANEL-DET Panel detect I 0 4.8 4.9
56 CD-ON CD power control O 0 0 5.1
57 PWR CNT Power control O 5.0 5.0 5.0
58 ACC-DET ACC detection I 5.1 5.1 5.1
59 RDSDATA RDSdata I 2.5 0 0
60 /RESET Reset input I 5.1 5.1 5.1
61 REM Remocon data input I 4.4 4.4 4.4
62 BATT Batterydetection I 5.1 5.1 5.1
63 RDSCLK RDSclock I 2.5 0 0
64 CD.C.STB CD.CH data strobe I 0 0 0
65 PWR-IC-MUTE Mute control O 5.1 5.1 5.1
66 CD-INSW1 CD insertdetection SW I 0 0 0
67 VSS Ground - 0 0 0
68 VDD +5Vpower supply - 5.1 5.1 5.1
69 X2 Crystal oscillator - 3.1 3.1 3.1
70 X1 Crystal oscillator - 2.2 2.2 2.2
71 Vpp (Ground pull-down) - 0 0 0
72 SUB-X2 Crystal oscillator - 3.1 3.1 3.1
73 SUB-X1 Crystal oscillator - 2.5 2.5 2.5
74 AVDD +5Vpower supply - 5.1 5.1 5.1
75 AVREF (Connecting to VDD) - 5.1 5.1 5.1
76 VSM_DET S-meter detection I 0 0 0
77 INITA Initial valueA I 0 0 0
78 INITB Initial valueB I 5.1 5.1 5.1
79 INITC Initial valueC I 5.1 5.1 5.1
80 INITD Initial valueD I 0 0 0
Note 1 :
Voltage measuerments are withrespect toground, witha voltmeter(internal resistance : 10M
ohms).
9.2. DisplayBlock
IC901 : YEAMLC75854T
8

Pin No. Port Descriptions I/O (V) (V)
1-8 SEG1-8 LCD segment O 2.5
9-35 SEG9-35 LCD segment O 2.5
36-39 NC No connection - -
40-43 COM1-4 LCD common O 2.5
44-49 KS1-6 Keydata output O 0.9
50-54 KI1-5 Keydata input I 0
55 TEST (Connecting to ground) - 0
56 VDD +5Vpower supply - 5.1
57 VDD1 Ground through capacitor - 3.3
58 VDD2 Ground through capacitor - 1.7
59 Vss Ground - 0
60 OSC CR oscillator - 3.9
61 DO Keydata output O 4.4
62 CE Chip enable I 0
63 CLK LCD clock I 0
64 DI LCD data input I 0
9.3. CD Servo Block
IC1 : C1BB00000665
Pin No. Port Descriptions I/O Vol.(V)
1D.GND Digital logicGround - 0
2 RFOK RFOK outputsignal O 5.0
3 /RST System reset I 5.1
4A0 Command/Parameter specification I 4.5
5 /STB Serial data strobe I 5.1
6 /SCK Data shift clock I 5.1
7SO Serial data O 0
8SI Serial data I 2.4
9XTALEN (Connecting to ground) - 0
10 D.VDD Digital logicpower supply - 5.0
11 DA.VDD DAC power supply - 4.8
12 R_OUT Audio R ch O 2.4
13 DA.GND DAC ground - 0
14 REGC Bypass capacitor for SCF regurator - 2.5
15 DA.GND DAC ground - 0
16 L_OUT Audio L ch O 2.4
17 DA.VDD DAC power supply - 4.8
18 R+ Notused - -
19 R- Notused - -
20 L- Notused - -
21 L+ Notused - -
22 X.VDD Crystal OSC power supply - 5.0
23 /XTAL Crystal OSC terminal - 2.4
24 XTAL Crystal OSC terminal - 2.2
25 X.GND Crystal OSC ground - 0
26 D.VDD Digital logicpower supply - 5.0
27 EMPH Notused - -
28 FLAG Notused - -
29 DIN DAC serial data I 2.6
30 DOUT DAC serial data O 2.6
31 SCKIN DAC shift clock I 2.7
32 SCKO DAC shift clock O 2.7
9

Pin No. Port Descriptions I/O Vol.(V)
33 LRCKIN DAC LRCK signal I 2.5
34 LRCK DAC LRCK signal O 2.5
35 HOLD/WDCK Notused - -
36 TX Notused - -
37 D.GND Digital logicGround - 0
38 C16M Notused - -
39 LIMIT (Connecting to VDD) - 5.0
40 D.VDD Digital logicpower supply - 5.0
41 LOCK EFMSYNC detection O 5.0
42 RFCK Notused - -
43 MIRR/WFCK Notused - -
44 PLCK Notused - -
45 D.GND Digital logicGround - 0
46 C1D1 Notused - -
47 C1D2 Notused - -
48 C2D1 Notused - -
49 C2D2 Notused - -
50 C2D3 Notused - -
51 D.VDD Digital logicpower supply - 5.0
52 PACK Notused - -
53 TSO Notused - -
54 TSI (Connecting to ground) - 0
55 /TSCK (Connecting to ground) - 0
56 TSTB (Connecting to ground) - 0
57 D.GND Digital logicGround - 0
58 TEST0 (Connecting to ground) - 0
59 TEST1 (Connecting to ground) - 0
60 ATEST Notused - 2.1
61 A.GND Analog logicGround - 0
62 FD Focusdrive O 2.6
63 TD Traking drive O 2.5
64 SD Sled drive O 2.5
65 MD Spindledrive O 2.6
66 DAC0 Notused - -
67 DAC1 Notused - -
68 DAC2 Notused - -
69 DAC3 Notused - -
70 A.VDD Analog logicpower supply - 5.0
71 EFM EFMsignal O 2.7
72 ASY Reference voltagefor EFMcomp. I 2.5
73 C3T Capacitor terminal for 3Tdetection - 2.7
74 RFI RF for EFMdata generation I 2.5
75 AGCO RF signal output(after gain adjustment) O 2.5
76 AGCI RF-AGC amp input I 2.5
77 RFO RF summing amp output O 2.8
78 EQ2 C/R terminal for RF amp equalizer - 2.6
79 EQ1 C/R terminal for RF amp equalizer - 0.5
80 RF- RF summing amp inverted input I 2.4
81 A.GND Analog logicGround - 0
82 A Photo detector Ainput I 2.7
83 C Photo detector C input I 2.5
84 B Photo detector B input I 2.7
85 D Photo detector D input I 2.5
86 F Photo detector F input I 3.0
10