Panasonic SL-CT582VGC User manual

©2005 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
SL-CT582VGC
SL-CT582VGN
SL-CT582VGS
Colour
(S)..........Silver Type
Portable CD Player
AD0503025CE

1 Accessories 2
2 Location of Controls 3
3 Precaution of Laser Diode 4
4 Handling Precautions for Traverse Deck 4
4.1. Handling of traverse deck (optical pick-up) 4
4.2. Caution when replacing traverse deck 4
4.3. Grounding for electrostatic breakdown prevention 4
5 Operation Checks and Component Replacement Procedures
5
5.1. Checking for the P.C.B. 5
5.2. Replacement for the CD lid unit 7
5.3. Replacement for the LCD, VOL/OPR etc. button,
MEMORY/EQ etc. button, Lid ornament and multi button
SW unit 8
5.4. Replacement for the retainer plate, open spring 1 and
open spring 2 8
5.5. Replacement for the traverse motor 9
5.6. Replacement for the optical pick-up 9
5.7. Replacement for the rest switch 11
6 Display of Self-Diagnostic Function 11
7 Checking the Operation Problems on the Traverse Deck
(Optical Pick-up) 12
7.1. Check the operations described below on the traverse
deck after replacing 12
8 Automatic Adjustment Results Display Function (Self-Check
Function) 13
· AC adaptor for SL-CT582VGC
(N0JDCE000001)..........................................1 pc.
· AC adaptor for SL-CT582VGS
(N0JDCE000002)..........................................1 pc.
· AC adaptor for SL-CT582VGN
(RFEA446A-S)...............................................1 pc.
· Stereo earphones
(L0BAB0000183)...........................................1 pc.
8.1. How to display automatic adjustment results 13
8.2. Display of automatic adjustment results (Self-Check
Function) 13
9 Type Illustration of ICs, Transistors and Diodes 14
10 Schematic Diagram Notes 15
10.1. Cautions in Repair exchange of the Diode (D1101, D1102)
15
11 Schematic Diagram 17
12 Printed Circuit Board and Wiring Connection Diagram 23
13 Block Diagram 25
14 Terminal Function of ICs 27
14.1. IC301(C2BBGF000593): System Control 27
14.2. IC501(MN6627962JB): Servo Amp, Servo Processor,
Digital Signal Processor, Digital Filter & D/A Converter 27
14.3. IC1301(C2FBEB000007): System Control/LCD Drive 28
15 Supply of Rechargeable Battery as Replacement Parts 29
16 Caution in use of Rechargeable Battery 29
17 Measurements and Adjustments 30
17.1. Tuner section 30
18 Replacement Parts List 31
19 Cabinet Parts Location 35
20 Traverse Unit Parts Location 36
21 Packaging 37
· Wired remote control
(N2QCBD000011)........................................1 pc.
· External battery case
(RFA2666-H).................................................1 pc.
· Rechargeable batteries (with case) for SL-CT582VGN only
(RFKFHHR4AGTB)......................................2 pcs.
· Power plug adaptor for SL-CT582VGC only
(K2DA42E00001)........................................1 pc.
CONTENTS
Page Page
1 Accessories
2
SL-CT582VGC / SL-CT582VGN / SL-CT582VGS

2 Location of Controls
3
SL-CT582VGC / SL-CT582VGN / SL-CT582VGS

The laser diode in the traverse deck (optical pick-up) may break
down due to potential difference caused by static electricity of
clothes or human body.
So, be careful of electrostatic breakdown during repair of the
traverse deck (optical pick-up).
4.1. Handling of traverse deck
(optical pick-up)
1. Do not subject the optical pick-up to static electricity as it is
extremely sensitive to electrical shock.
2. To protect the laser diode against electrostatic breakdown,
be sure that the short land of the flexible board (FFC board)
should be short-circuit by solder before pulling out the FFC.
Then inserting a short pin or similar object into the tip of the
flexible board.
(Refer to Fig. 4-1.)
3. Take care not to apply excessive stress to the flexible board
(FFC board).
4. Do not turn the variable resistor (laser power adjustment). It
has already been adjusted. (Refer to Fig. 4-1.)
Fig. 4-1.
4.2. Caution when replacing
traverse deck
The new traverse deck short-circuits by the short pin, the foil
(B) and short lands to protect the laser diode against
electrostatic breakdown. Be sure to replace to new one
following procedures.
1. Remove the short pin from the FFC, and then connect it to
the connector.
2. Cut the foil (B). (Refer to Fig. 4-1.) (Take care not to make
contact with cutting point each other.)
3. Unsolder the short lands. (Refer to Fig. 4-1.)
4.3. Grounding for electrostatic
breakdown prevention
4.3.1. Human body grounding
Use the anti-static wrist strap to discharge the static electricity
from your body. (Refer to Fig. 4-2.)
Fig. 4-2.
4.3.2. Work table grounding
Put a conductive material (sheet) or steel sheet on the area
where the traverse deck (optical pick-up) is placed, and ground
the sheet. (Refer to Fig. 4-3.)
Fig. 4-3.
Caution:
The static electricity of your clothes will not be grounded
through the wrist strap.
So take care not to let your clothes touch the traverse deck
(optical pick-up).
3 Precaution of Laser Diode
Caution:
This product utilizes a laser diode with the unit turned on, invisible laser radiation is emitted from the pick-up lens.
Wavelength: 780 nm
Maximum output radiation power from pick-up: 100 µW/VDE
Laser radiation from the pick-up lens is safety level, but be sure the followings:
1. Do not disassemble the optical pick-up unit, since radiation from exposed laser diode is dangerous.
2. Do not adjust the variable resistor on the pick-up unit. It was already adjusted.
3. Do not look at the focus lens using optical instruments.
4. Recommend not to look at pick-up lens for a long time.
4 Handling Precautions for Traverse Deck
4
SL-CT582VGC / SL-CT582VGN / SL-CT582VGS

· This section describes procedures for checking the
operation of the major printed circuit boards and
replacing the main components.
· For reassembly after operation checks or replacement,
reverse the respective procedures. Special reassembly
procedures are described only when required.
5.1. Checking for the P.C.B.
5.1.1. Checking for the P.C.B. (A side)
5 Operation Checks and Component Replacement
Procedures
5
SL-CT582VGC / SL-CT582VGN / SL-CT582VGS

· Check the P.C.B. (A side) as shown below.
5.1.2. Checking for the P.C.B. (B side)
· Follow the (Step 1) -(Step 7) of item 5.1.1.
· Check the P.C.B. (B side) as shown below.
6
SL-CT582VGC / SL-CT582VGN / SL-CT582VGS

5.2. Replacement for the CD lid
unit
· Follow the (Step 1) -(Step 5) of item 5.1.1.
7
SL-CT582VGC / SL-CT582VGN / SL-CT582VGS

5.3. Replacement for the LCD,
VOL/OPR etc. button,
MEMORY/EQ etc. button, Lid
ornament and multi button SW
unit
· Follow the (Step 1) -(Step 5) of item 5.1.1.
· Follow the (Step 1) -(Step 4) of item 5.2.
5.4. Replacement for the retainer
plate, open spring 1 and open
spring 2
· Follow the (Step 1) -(Step 5) of item 5.1.1.
· Follow the (Step 1) -(Step 4) of item 5.2.
8
SL-CT582VGC / SL-CT582VGN / SL-CT582VGS

5.5. Replacement for the traverse
motor
· Follow the (Step 1) -(Step 4) of item 5.1.1.
5.6. Replacement for the optical
pick-up
· Follow the (Step 1) -(Step 4) of item 5.1.1.
· Follow the (Step 1) -(Step 3) of item 5.5.
9
SL-CT582VGC / SL-CT582VGN / SL-CT582VGS

10
SL-CT582VGC / SL-CT582VGN / SL-CT582VGS