Panasonic KX-TC1206TWB User manual

ORDERNO. KM40111737C3
Telephone Equipment
KX-TC1206TWB / KX-TC1206TWS / KX-TC1206TWF / KX-
TC1206TWP
Cordless Phone
Black Version
Silver Version
Blue Version
Pink Version
(for Taiwan)
SPECIFICATIONS
1

2001 Kyushu Matsushita ElectricCo., Ltd. All rights reserved.
Unauthorized copying and distribution isaviolation of law.
1. BATTERY
1.1. Recharge
2

1.2. Batteryinformation
2. BATTERY REPLACEMENT
3

3. LOCATION OF CONTROLS
3.1. Base Unit
4

3.2. Handset
5

4. CONNECTION
6

-USE ONLY WITHPanasonicAC ADAPTORPQLV16TWZ.
-The AC adaptor must remainconnected at all times.
(Itisnormal for the adaptor to feel warm during use.)
-When more than one unitisused, the units mayinterfere with each
other. To prevent or reduce interference, please leave ample
space between the base units.
7

4.1. Adding Another Phone
This unit will not function during a powerfailue. To connect a standardtelephone on the same
line, use a T-adaptor.
8

5. OPERATIONS
5.1. Making Calls
5.2. Answering Calls
9

5.3. Storing Phone Numbers inMemory
5.4. Storing aPhone Number inthe DIRECTButton
10

5.5. Dialing aStored Number
5.6. Dialing the Stored Number inthe DIRECTButton
11

5.7. Flash Button
6. DISASSEMBLY INSTRUCTIONS
12

ShowinFig. Procedure To remove. Remove.
1 1 LowerCabinet Screws (2.6 × 12)....................... (A) × 4
2 1, 2 MainP.C. Board Screws (2.6 × 6).......................... (B) ×
1
Solder
MainP.C. Board.
13

ShowinFig. Procedure To remove. Remove.
3 3 RearCabinet Batterycompartment cover.
43, 4 Screws (2.6 × 12)......................(C) × 2
5 3, 4, 5 MainP. C. Board Screw(2.6 × 12)........................(D) × 1
Tape and solder.
MainP. C. Board.
7. TROUBLESHOOTING GUIDE
14

Cross Reference:
Check Power ()
Bell Reception ()
Check Battery Charge ()
Check Link ()
Check Handset Transmission ()
Check Handset Reception ()
7.1. Check Power
15

Cross Reference:
Reset Circuit (Base Unit) ()
Power Supply Circuit ()
Note:
CPU: IC2
Cross Reference:
Charge Circuit ()
Note:
CPU: IC2
*: Eachmeasurement points are shownin CIRCUIT BOARD (Base Unit) () or CIRCUIT BOARD
(Handset) ()
7.2. Bell Reception
16

Cross Reference:
Check Link ()
Telephone Line Interface ()
Note:
CPU: IC2
Cross Reference:
Check Link ()
-Incase of the following suffix, the bell might not stop even after
keywas pressed to answer the call.
Inthiscase, the Base Unitand the Handset might have been
mixed up at the customer side.
Therefore, each of these units shouldbe replaced to the original
ones which have the same suffix.
*: Eachmeasurement points are shownin CIRCUIT BOARD (Base Unit) () or CIRCUIT BOARD
(Handset) ()
7.3. Check BatteryCharge
17

Cross Reference:
Charge Circuit ()
Power Supply Circuit ()
Note:
CPU: IC2
Cross Reference:
Reset Circuit (Handset) ()
Note:
CPU: IC2
*: Eachmeasurement points are shownin CIRCUIT BOARD (Base Unit) () or CIRCUIT BOARD
(Handset) ()
18

7.4. Check Link
**: Referto Adjustment ()
Note:
CPU: IC2
RFIC: IC1
*: Eachmeasurement points are shownin CIRCUIT BOARD (Base Unit) () or CIRCUIT BOARD
(Handset) ()
19

**: Referto Adjustment ().
Note:
CPU: IC2
RFIC: IC1
*: Eachmeasurement points are shownin CIRCUIT BOARD (Base Unit) () or CIRCUIT BOARD
20