Panasonic KX-TG7200FX User manual

PQQW15775ZA DC0607DA0 FX-3/4
This unit is designed to be used in Czech, Slovakia, and central Europe. To use this unit in your
country, first change the unit’s region setting to match your country. Change the unit’s display
language as needed. Refer to “Changing the unit’s region setting” in the operating instructions.
Connections
Important:
LIf you use a telephone line cord which is not supplied, the unit may not work
properly.
To telephone line USE ONLY the supplied AC adaptor.
Base unit
“Click”
(220–240 V, 50 Hz)
USE ONLY the supplied cord.
Hook
Press plug firmly.
(220–240 V, 50 Hz)
(KX-TG7202)
USE ONLY the supplied AC adaptor (smaller).
Charger Press plug firmly.
Hooks
Digital Cordless Phone
Model No. KX-TG7200FX/KX-TG7202FX
Digital Cordless Answering System
Model No. KX-TG7220FX
Quick Guide
TG7200_7220FX(e-e)_QG.fm Page 1 Thursday, June 21, 2007 5:10 PM
All manuals and user guides at all-guides.com
all-guides.com

– 2 –
Battery installation/Battery charge
Initial charge: 7 hours
Note:
LUSE ONLY rechargeable Ni-MH batteries.
LDo NOT use Alkaline/Manganese/Ni-Cd batteries.
Operating tips
Using the navigator key
Press {^}, {V}, {<}, or {>}to navigate
through menus and to select items shown
on the display.
Adjusting the receiver or speaker
volume (?)
Press {^} or {V} while on a call.
Display language
16 display languages are available.
You can select “Deutsch”, “English”, “Magyar”, “Polski”, “SlovenČina”,
“ČeŠtina”, “Hrvatski”, “Slovenscina”, “Eesti”, “LIETUVIŠKAI”,
“LatvieŠu”, “Românã”, “БЪЛГАРСКИ”, “Srpski”, “МАКЕДОНСКИ”, or “Shqip”.
1{ih} i{j/OK}
2Press {^} or {V} to select “Handset Setup”. i{>}
3Press {^} or {V} to select “Display Setup”. i{>}
4Press {^} or {V} to select “Select Language”. i{>}
5Press {^} or {V} to select the desired language. i{>}i{ih}
Base unit *1 Charger *2
*1 The pictured model is KX-TG7200.
*2 KX-TG7202
Rechargeable
Ni-MH ONLY
“Charging” will
be displayed.
{V}
{^}
{<}{>}
TG7200_7220FX(e-e)_QG.fm Page 2 Thursday, June 21, 2007 5:10 PM
All manuals and user guides at all-guides.com

– 3 –
Dialling mode (tone/pulse)
1{j/OK}
2Press {^} or {V} to select “Base Unit Setup”. i{>}
3Press {^} or {V} to select “Call Options”. i{>}
4Press {^} or {V} to select “Dial Mode”. i{>}
5Press {^} or {V} to select the desired setting. i{>}i{ih}
Date and time
1{j/OK}
2Press {^} or {V} to select “Handset Setup”. i{>}
3Press {^} or {V} to select “Time Settings”. i{>}
iPress {^} or {V} to select “Set Date & Time”. i{>}
4Enter the current date, month, and year.
5Enter the current hour and minute.
6{j/OK}i{ih}
TG7200_7220FX(e-e)_QG.fm Page 3 Thursday, June 21, 2007 5:10 PM
All manuals and user guides at all-guides.com

– 4 –
Basic operations
CMaking/Answering calls (Handset)
Making calls Dial the phone number. i{C}/{s}
Answering calls {C}/{s}
Hanging up {ih}
Receiver/speaker volume Press {^} or {V} while on a call.
Making a call using the redial
list
{R} i{^}/{V}: Select the desired number.
i{C}
Handset ringer volume 1{j/OK}
2{^}/{V}: “Handset Setup”i{>}
3{^}/{V}: “Ringer Setup”i{>}
4{^}/{V}: “Ringer Volume”i{>}
5{^}/{V}: Select the desired volume. i{>}
i{ih}
kPhonebook (Handset)
Adding entries (names and
phone numbers)
1{k} i{j/OK}
2{^}/{V}: “New Entry”i{>}
3Enter the party’s name (16 characters max.).
i{j/OK}
4Enter the party’s phone number (24 digits max.).
i{j/OK}
5{^}/{V}: “Save”i{>}i{ih}
LTo enter a name, see the character table in the
operating instructions.
Making calls 1{k}
2{^}/{V}: Select the desired entry. i{C}
IAnswering system (Base unit): KX-TG7220
Answering on/off Press {s}to turn on/off the answering system.
Listening to messages {6}
TG7200_7220FX(e-e)_QG.fm Page 4 Thursday, June 21, 2007 5:10 PM
All manuals and user guides at all-guides.com

– 5 –
Frequently asked questions
Question Cause & solution
Why is wflashing? LThe handset is too far from the base unit. Move
closer.
LThe base unit AC adaptor is not connected.
Check the connections.
LYou are using the handset or base unit in an area
with high electrical interference. Place the
handset and base unit away from interference
sources, such as antennas and mobile phones.
LThe handset is not registered to the base unit.
Register it (page 7).
Why can I not make calls? LThe dialling mode setting is incorrect. Set to
“Tone”or “Pulse”as needed.
What should I do when the
handset does not turn on?
LMake sure that the batteries are installed
correctly.
LFully charge the batteries.
LClean the charge contacts and charge again.
How long is the battery
operating time?
LWhen you are using fully-charged Ni-MH batteries
(supplied batteries);
In continuous use: 17 hours max.
In continuous standby mode: 180 hours max.
LIt is normal for batteries not to reach full capacity
at the initial charge. Maximum battery
performance is reached after a few complete
cycles of charge/discharge (use).
LActual battery performance depends on a
combination of how often the handset is in use
and how often it is not in use (standby).
Can I keep the handset on
the base unit or charger
when I am not using it?
LEven after the handset is fully charged, the
handset can be left on the base unit or charger
without any ill effect on the batteries.
When should I replace the
batteries?
LIf the batteries are fully charged until 5 is
displayed, but
7 is displayed after a few calls,
replace the batteries with new ones.
What is a PIN? LThe PIN is a 4-digit number that must be entered
in order to change certain base unit settings. The
default PIN is “0000”.
TG7200_7220FX(e-e)_QG.fm Page 5 Thursday, June 21, 2007 5:10 PM
All manuals and user guides at all-guides.com

– 6 –
What do I need to do to
display caller information?
LYou need to subscribe to Caller ID service.
Consult your service provider/telephone company
for details.
LThe message “You must first subscribe
to Caller ID.” will be displayed until you
receive caller information after subscribing to
Caller ID service.
What should I do when:
– I hear static or sound cuts
in and out?
– there is interference from
other electrical units?
LPlace the handset and the base unit away from
other electrical appliances.
LMove closer to the base unit.
LYour unit is connected to a telephone line with
DSL service. We recommend connecting a filter
(contact your DSL service provider) to the
telephone line between the base unit and the
telephone line jack.
What should I do when the
operating time seems to be
short even after I fully
charged the batteries?
LWipe the battery ends (S, T) and the unit
contacts with a dry cloth.
What do I need to do to
erase the missed call
number (for example,
“3 Calls”) from the
display?
LThere are unviewed missed calls remaining. View
them using the following method.
1{j/OK}
2{^}/{V}: “Caller List”i{>}
3Press {V} to search from the most recent call,
or press {^} to search from the oldest call.
Frequently asked questions
Question Cause & solution
TG7200_7220FX(e-e)_QG.fm Page 6 Thursday, June 21, 2007 5:10 PM
All manuals and user guides at all-guides.com
all-guides.com

– 7 –
Registering a handset to the base unit
The supplied handset and base unit are pre-registered. When you purchase an
additional handset, refer to the additional handset’s installation manual for
registration. If for some reason the handset is not registered to the base unit, register
the handset.
1{j/OK}
2{^}/{V}: “Handset Setup”i{>}
3{^}/{V}: “Registration”i{>}
4{^}/{V}: “Register H.set”i{>}
5Proceed with the operation for your model.
NKX-TG7200/KX-TG7202
Press and hold {x} on the base unit for
about 5 seconds. (No registration tone)
NKX-TG7220
Press and hold {x} on the base unit for
about 5 seconds, until the registration tone
sounds.
6Wait until “Enter Base PIN”is displayed.
iEnter the base unit PIN (default: “0000”).
i{j/OK}
{j/OK}
{x}
{x}
{j/OK}
TG7200_7220FX(e-e)_QG.fm Page 7 Thursday, June 21, 2007 5:10 PM
All manuals and user guides at all-guides.com

– 8 –
Optional services (Caller ID and SMS)
If you subscribe to Caller ID service, you can:
– display caller information
To use SMS, you must subscribe to Caller ID and/or appropriate service.
SMS (Short Message Service)
012345
TG7200_7220FX(e-e)_QG.fm Page 8 Thursday, June 21, 2007 5:10 PM
All manuals and user guides at all-guides.com