Panasonic AW-UE160WP User manual

DVQP2861YA
W0223GU1053 -FJ
ENGLISH
Model No. AW‑UE160WP
Model No. AW‑UE160KP
Model No. AW‑UE160WPC
Model No. AW‑UE160KPC
Model No. AW‑UE160WE
Model No. AW‑UE160KE
Model No. AW‑UE160WED
Model No. AW‑UE160KED
Operating Instructions
4K Integrated Camera
Before operating this product, please read the instructions carefully and save this manual for future use.
Please carefully read the “Read this first!” (pages 2 to 8) of this Manual before use.
PJ PC EJ ED

Read this first! (For AW‑UE160WP, AW‑UE160KP)
WARNING:
• To reduce the risk of fire or electric shock, do not expose this
equipment to rain or moisture.
• To reduce the risk of fire or electric shock, keep this equipment
away from all liquids. Use and store only in locations which are
not exposed to the risk of dripping or splashing liquids, and do
not place any liquid containers on top of the equipment.
WARNING:
Always keep the main unit mounting screw, bracket mounting
screws and drop-prevention wire mounting screw out of the
reach of infants and small children.
WARNING:
Installation should only be performed by qualified installation
personnel.
Improper installation may result in the entire apparatus falling
down and causing injury.
CAUTION:
Do not remove panel covers by unscrewing.
To reduce the risk of electric shock, do not remove the covers.
No user serviceable parts inside.
Refer servicing to qualified service personnel.
CAUTION:
In order to maintain adequate ventilation, do not install or place
this unit in a bookcase, built-in cabinet or any other confined
space. To prevent risk of electric shock or fire hazard due to
overheating, ensure that curtains and any other materials do not
obstruct the ventilation.
CAUTION:
To reduce the risk of fire or electric shock and annoying
interference, use the recommended accessories only.
CAUTION:
Check the installation at least once a year.
An improper installation could cause the unit to fall off resulting
in personal injury.
CAUTION:
A coin type battery is installed inside of the unit.
Do not expose the unit to excessive heat such as sunshine, fire
or the like.
indicates safety information.
FCC NOTICE (USA)
Supplier’s Declaration of Conformity
Model Number: AW-UE160WP/AW-UE160KP
Trade Name: Panasonic
Responsible Party: Panasonic Corporation of North America
Two Riverfront Plaza, Newark, NJ 07102
Support contact: 1-800-524-1448
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
FCC Note:
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
Warning:
To assure continued FCC emission limit compliance, the user must use only shielded interface cables when connecting to external units. Also,
any unauthorized changes or modifications to this equipment could void the user’s authority to operate it.
indicates safety information.
The symbols on this product (including the accessories) represent the following:
DC
TO REMOVE BATTERY
Back‑up Battery (Lithium Battery)
• For the removal of the battery for disposal at the end of
its service life, please consult your dealer.
2

Read this first! (For AW‑UE160WPC, AW‑UE160KPC)
WARNING:
• To reduce the risk of fire or electric shock, do not expose this
equipment to rain or moisture.
• To reduce the risk of fire or electric shock, keep this equipment
away from all liquids. Use and store only in locations which are
not exposed to the risk of dripping or splashing liquids, and do
not place any liquid containers on top of the equipment.
WARNING:
Always keep the main unit mounting screw, bracket mounting
screws and drop-prevention wire mounting screw out of the
reach of infants and small children.
WARNING:
Installation should only be performed by qualified installation
personnel.
Improper installation may result in the entire apparatus falling
down and causing injury.
CAUTION:
Do not remove panel covers by unscrewing.
To reduce the risk of electric shock, do not remove the covers.
No user serviceable parts inside.
Refer servicing to qualified service personnel.
CAUTION:
In order to maintain adequate ventilation, do not install or place
this unit in a bookcase, built-in cabinet or any other confined
space. To prevent risk of electric shock or fire hazard due to
overheating, ensure that curtains and any other materials do not
obstruct the ventilation.
CAUTION:
To reduce the risk of fire or electric shock and annoying
interference, use the recommended accessories only.
CAUTION:
Check the installation at least once a year.
An improper installation could cause the unit to fall off resulting
in personal injury.
CAUTION:
To reduce the risk of fire or electric shock caused by damage to
the power supply cord, do not squeeze, bend, or pull the power
supply cord when using the apparatus.
CAUTION:
A coin type battery is installed inside of the unit.
Do not expose the unit to excessive heat such as sunshine, fire
or the like.
indicates safety information.
FCC NOTICE (USA)
Supplier’s Declaration of Conformity
Model Number: AW-UE160WPC/AW-UE160KPC
Trade Name: Panasonic
Responsible Party: Panasonic Corporation of North America
Two Riverfront Plaza, Newark, NJ 07102
Support contact: 1-800-524-1448
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
FCC Note:
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
Warning:
To assure continued FCC emission limit compliance, the user must use only shielded interface cables when connecting to external units. Also,
any unauthorized changes or modifications to this equipment could void the user’s authority to operate it.
indicates safety information.
NOTIFICATION (Canada)
CAN ICES-003 (A)/NMB-003(A)
The symbols on this product (including the accessories) represent the
following:
DC
3

TO REMOVE BATTERY
Back‑up Battery (Lithium Battery)
• For the removal of the battery for disposal at the end of
its service life, please consult your dealer.
Battery recycling symbol (valid only in Taiwan)
4
Read this first! (For AW‑UE160WPC, AW‑UE160KPC) (continued)

WARNING:
• To reduce the risk of fire or electric shock, do not expose this
equipment to rain or moisture.
• To reduce the risk of fire or electric shock, keep this equipment
away from all liquids. Use and store only in locations which are
not exposed to the risk of dripping or splashing liquids, and do
not place any liquid containers on top of the equipment.
WARNING:
Always keep the main unit mounting screw, bracket mounting
screws and drop-prevention wire mounting screw out of the
reach of infants and small children.
WARNING:
This equipment is compliant with Class A of CISPR 32.
In a residential environment this equipment may cause radio
interference.
WARNING:
Installation should only be performed by qualified installation
personnel.
Improper installation may result in the entire apparatus falling
down and causing injury.
CAUTION:
Do not remove panel covers by unscrewing.
To reduce the risk of electric shock, do not remove the covers.
No user serviceable parts inside.
Refer servicing to qualified service personnel.
CAUTION:
In order to maintain adequate ventilation, do not install or place
this unit in a bookcase, built-in cabinet or any other confined
space. To prevent risk of electric shock or fire hazard due to
overheating, ensure that curtains and any other materials do not
obstruct the ventilation.
CAUTION:
To reduce the risk of fire or electric shock and annoying
interference, use the recommended accessories only.
CAUTION:
Check the installation at least once a year.
An improper installation could cause the unit to fall off resulting
in personal injury.
CAUTION:
A coin type battery is installed inside of the unit.
Do not expose the unit to excessive heat such as sunshine, fire
or the like.
indicates safety information.
The symbols on this product (including the accessories) represent the following:
DC
TO REMOVE BATTERY
Back‑up Battery (Lithium Battery)
• For the removal of the battery for disposal at the end of
its service life, please consult your dealer.
Read this first! (For AW‑UE160WE, AW‑UE160KE, AW‑UE160WED, AW‑UE160KED)
5

Read this first! (For AW‑UE160WE, AW‑UE160KE)
EMC NOTICE FOR THE PURCHASER/USER OF THE APPARATUS
1. Pre‑requisite conditions to achieving compliance with the above standards
<1> Peripheral equipment to be connected to the apparatus and special connecting cables
• The purchaser/user is urged to use only equipment which has been recommended by us as peripheral equipment to be connected to the apparatus.
• The purchaser/user is urged to use only the connecting cables described below.
<2> For the connecting cables, use shielded cables which suit the intended purpose of the apparatus.
• Video signal connecting cables
Use double shielded coaxial cables, which are designed for 75-ohm type high-frequency applications, for SDI (Serial Digital Interface).
Coaxial cables, which are designed for 75-ohm type high-frequency applications, are recommended for analog video signals.
• Audio signal connecting cables
If your apparatus supports AES/EBU serial digital audio signals, use cables designed for AES/EBU.
Use shielded cables, which provide quality performance for high-frequency transmission applications, for analog audio signals.
• Other connecting cables (IEEE1394, USB)
Use double shielded cables, which provide quality performance for high-frequency applications, as connecting cables.
• When connecting to the DVI signal terminal, use a cable with a ferrite core.
• If your apparatus is supplied with ferrite core(s), they must be attached on cable(s) following instructions in this manual.
2. Performance level
The performance level of the apparatus is equivalent to or better than the performance level required by these standards.
However, the apparatus may be adversely affected by interference if it is being used in an EMC environment, such as an area where strong
electromagnetic fields are generated (by the presence of signal transmission towers, cellular phones, etc.). In order to minimize the adverse
effects of the interference on the apparatus in cases like this, it is recommended that the following steps be taken with the apparatus being
affected and with its operating environment:
1. Place the apparatus at a distance from the source of the interference.
2. Change the direction of the apparatus.
3. Change the connection method used for the apparatus.
4. Connect the apparatus to another power outlet where the power is not shared by any other appliances.
WARNING:
THIS PRODUCT CONTAINS A COIN
BATTERY
Keep coin battery out of the reach of infants
and small children whether the battery is
new or used. Severe or fatal injuries can
occur within 2 hours of ingestion. Seek
medical attention immediately.
Turkey Only
AEEE Yönetmeliğine Uygundur.
AEEE Complies with Directive of Turkey.
Disposal of Old Equipment
Only for European Union and countries with recycling systems
This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products must not
be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection points in accordance with your
national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on human health and
the environment. For more information about collection and recycling, please contact your local municipality, dealer or supplier.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
Manufactured by:
Panasonic Connect Co., Ltd.
4-1-62 Minoshima, Hakata-ku, Fukuoka 812-8531, Japan
Importer:
Panasonic Connect Europe GmbH
Hagenauer Strasse 43, 65203 Wiesbaden, Germany
Authorized Representative in EU:
Panasonic Connect Europe GmbH
Panasonic Testing Centre
Winsbergring 15, 22525 Hamburg, Germany
Importer for UK:
Panasonic Connect UK,
a branch of Panasonic Connect Europe GmbH,
Maxis 2, Western Road, Bracknell, Berkshire, RG12 1RT
6

Інформація для покупця
Виробник: Panasonic Connect Co., Ltd. Панасонік Коннект Ко., Лтд.
Адреса виробника: Fukuoka, Japan Фукуока Японія
Країна походження: Japan/China Японія/Китай
Імпортер: ТОВ "ПАНАСОНІК УКРАЇНА ЛТД"
Адреса імпортера: вул. Васильківська, буд. 30, м. Київ
03022, Україна
Примітки:
Термін служби виробу 7 років
Дата виготовлення може бути визначена за допомогою комбінації літер та цифр серійного номера, розташованого на продукті.
Приклад: X X XXXXXXX
Рік: остання цифра року (7 – 2017, 8 – 2018,…0 – 2020)
Місяць: А – Січень, В – Лютий… L – Грудень
Information for Users in India
Information on hazardous constituents as specified in the E-Waste (Management) Rules in electrical and electronic equipment.
Declaration of Conformity with the requirements of the E-Waste (Management) Rules limits with respect to Lead, Mercury, Cadmium, Hexavalent
chromium, Polybrominated biphenyls,Polybrominated diphenyl ethers.
The content of hazardous substance with the exemption of the applications listed in the E-Waste (Management) Rules:
1. Lead (Pb) – not over 0.1% by weight.
2. Cadmium (Cd) – not over 0.01% by weight.
3. Mercury (Hg) – not over 0.1% by weight.
4. Hexavalent chromium (Cr6+) – not over 0.1% by weight.
5. Polybrominated biphenyls (PBBs) – not over 0.1% by weight.
6. Polybrominated diphenyl ethers (PBDEs) – not over 0.1% by weight.
For the purpose of recycling to facilitate effective utilization of resources, please return this product to a nearby authorized collection
center, registered dismantler of recycler, or Panasonic service center when disposing of this product.
Customer care number (Toll free) : 1800 103 1333 ,1800 108 1333
Please see the Panasonic website for further information on collection centers, etc. or call the customer care toll-free number.
https://www.panasonic.com/in/corporate/e-waste-management.html
Do’s & Don’ts
No. Do’s Don’ts
1All electrical and electronic products are required to be handed over
only to the Authorized recycler.
The product should not be opened by the user himself / herself, but
only by authorized service personnel.
2The product should be handed over only to authorized recycler for
disposal.
The product is not meant for re-sale to any unauthorized agencies /
scrap dealers / kabariwalas.
3Keep the product in an isolated area, after it becomes non-
functional / unrepairable so as to prevent its accidental breakage.
The product is not meant for mixing into household waste stream.
4Refer to Operating Instructions for handling of end of life products. Do not keep any replaced spare part(s) from the product in an
exposed area.
5
Always dispose of products that have reached end of life at
Panasonic Life Solutions India Authorized Service Centre.
Do not donate old electronic items to anybody.
Do not dispose of your product in garbage bins along with municipal
waste that ultimately reaches landfill.
6
Wherever possible or as instructed, separate the packaging material
according to responsible waste disposal options and sorting for
recycling.
Do not give e-waste to informal and unorganized sectors like Local
Scrap Dealers / Rag Pickers.
7
Read this first! (For AW‑UE160WE, AW‑UE160KE) (continued)

Read this first!
Note on grounding
• Ground the unit via the <SIGNAL GND> ground connector.
SIGNAL
GND
Ground connector
to ground
connector on wall
outlet, ground bar,
etc.
 Trademarks and registered trademarks
• Microsoft®, Windows®, Windows®10, Microsoft Edge, Internet
Explorer®, ActiveX®and DirectX®are either registered trademarks
or trademarks of Microsoft Corporation in the United States and
other countries.
• Apple, Mac, macOS, iPadOS, iPhone, iPad, and Safari are
registered trademarks of Apple Inc., in the United States and other
countries.
• Android™ and Chrome™ browser are trademarks of Google LLC.
• Intel®and Intel®Core™ are trademarks or registered trademarks
of Intel Corporation in the United States and other countries.
• Adobe®and Reader®are either registered trademarks or
trademarks of Adobe Systems Incorporated in the United States
and/or other countries.
• The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing Administrator, Inc. in the United States and other
countries.
• NDI is a registered trademark of NewTek, Inc. in the United
States.
• Other names of companies and products contained in these
Operating Instructions may be trademarks or registered
trademarks of their respective owners.
 About copyright and licence
It is expressly prohibited to distribute, copy, disassemble, reverse
compile, modify, reverse engineer, or export in violation of export
laws the software provided with the unit.
 Abbreviations
The following abbreviations are used in this manual.
• Windows®Internet Explorer®11 32/64-bit is abbreviated to
“Internet Explorer”.
For the purposes of this manual, the model numbers of the units are
given as listed in the table below.
Model number of unit Model number given in
manual
AW-UE160WP, AW-UE160KP,
AW-UE160WPC, AW-UE160KPC,
AW-UE160WE, AW-UE160KE,
AW-UE160WED, AW-UE160KED
AW‑UE160
AW-RP150G AW‑RP150
AW-RP60G AW‑RP60
AV-HLC100P, AV-HLC100E AV‑HLC100
AV-UHS500P, AV-UHS500E AV‑UHS500
 Illustrations and screen displays featured
in the manual
• What is shown in the manual’s illustrations and screen displays
may differ from how it is actually appears.
• Functions only available with Microsoft Edge (IE mode) are
indicated with the symbol.
• The screenshots are used in accordance with the guidelines of
Microsoft Corporation.
8

Contents
Read this first! (For AW‑UE160WP, AW‑UE160KP)............................ 2
Read this first! (For AW‑UE160WPC, AW‑UE160KPC)....................... 3
Read this first! (For AW‑UE160WE, AW‑UE160KE, AW‑UE160WED,
AW‑UE160KED) ................................................................................. 5
Read this first! (For AW‑UE160WE, AW‑UE160KE)............................ 6
Read this first! ...................................................................................... 8
Note on grounding ............................................................................... 8
Before use............................................................................................ 10
Overview............................................................................................ 10
Computer requirements ..................................................................... 10
Disclaimer of warranty ....................................................................... 11
Network security ................................................................................ 11
Features................................................................................................ 12
Accessories ......................................................................................... 14
How to remove the lens cap .............................................................. 14
Optional accessories .......................................................................... 14
Operating precautions ........................................................................ 15
Wireless remote control (optional accessory).................................. 17
Parts and their functions .................................................................... 18
Camera unit ....................................................................................... 18
Wireless remote control: AW-RM50AG (optional accessory) ............ 31
Setting the remote control IDs ........................................................... 32
Network settings.................................................................................. 33
Using EasyIP Setup Tool Plus to make settings for the unit.............. 33
Setting the initial account................................................................... 34
Installing the plug-in viewer software................................................. 35
Basic shooting operations ................................................................. 36
How to turn the power on and off ...................................................... 37
Turning the power on......................................................................... 37
Turning the power off......................................................................... 37
Selecting the units............................................................................... 38
Shooting............................................................................................... 39
What to do when encountering problems in the basic shooting
operations ........................................................................................ 40
More advanced operations................................................................. 41
Manual shooting.................................................................................. 42
Manually adjusting the focus.............................................................. 42
Manually adjusting the iris.................................................................. 42
Manually adjusting the shutter speed ................................................ 42
Manually adjusting the gain ............................................................... 42
Preset memories.................................................................................. 43
White balance adjustment .................................................................. 44
Automatic adjustment (AWB: AWB A or AWB B) .............................. 44
Auto tracking white adjustment (ATW)............................................... 45
3200K and 5600K presets ................................................................. 45
VAR.................................................................................................... 45
Black balance adjustment .................................................................. 46
Automatic adjustment ........................................................................ 46
Black level (master pedestal) adjustment......................................... 46
Genlock adjustment ............................................................................ 47
Horizontal phase adjustment ............................................................. 47
Camera menu items ............................................................................ 48
Top Menu screen............................................................................... 48
BASIC CONFIG ................................................................................. 48
NETWORK......................................................................................... 51
OUTPUT ............................................................................................ 52
RETURN............................................................................................ 56
AUDIO................................................................................................ 56
IP SIGNAL ......................................................................................... 57
PAINT ................................................................................................ 58
LENS.................................................................................................. 69
MONITOR DISPLAY.......................................................................... 70
TRACKING DATA OUTPUT.............................................................. 71
CROP................................................................................................. 72
PAN/TILT ........................................................................................... 74
PRESET............................................................................................. 77
FILES................................................................................................. 81
MAINTENANCE................................................................................. 81
Camera menu item table..................................................................... 84
Displaying the web screen ............................................................... 101
Displaying the web screen using a personal computer.................... 101
Switching between the Live screen [Live] and Web setup screen
[Setup] ......................................................................................... 103
Logging into the Web screen ........................................................... 103
Web screen operations..................................................................... 104
Live screen [Live]............................................................................. 104
Web screen configurations .............................................................. 110
Web setup screen [Setup]................................................................ 110
Setting status screen [Setting status]............................................... 112
System screen [System] .................................................................. 112
Image screen [Image/Audio]............................................................ 125
Collaboration capability [Linkage] .................................................... 164
User management screen [User mng.]............................................ 167
Network setup screen [Network]...................................................... 169
Maintenance screen [Maintenance]................................................. 186
Displaying the web screen using a personal computer equipped
with a touch panel ......................................................................... 190
Displaying the web screen using a mobile terminal ...................... 192
Camera control screen [Camera Control] ........................................ 192
Limiters............................................................................................... 194
Setting/releasing the limiters ........................................................... 195
Basic limiter operations.................................................................... 195
Setting the limiters ........................................................................... 195
Releasing the limiters....................................................................... 195
Resetting the limiters ....................................................................... 195
Safe mode .......................................................................................... 196
Concerning the safe mode............................................................... 196
Detection of equipment trouble........................................................ 196
Troubleshooting ................................................................................ 197
Specifications .................................................................................... 205
Index ................................................................................................... 208
9

Before use
Overview
• This product is an all-in-one pan-tilt head remote camera, compatible
with 4K/12G-SDI and SMPTE ST2110*1, and also compatible with
4K/60p and 2K/120p.
*1A separate optional software key (AW-SFU60) needs to be
purchased to enable SMPTE ST2110 functionality.
Use EasyIP Setup Tool Plus to activate AW-SFU60. Refer to the
operating instructions available on the EasyIP Setup Tool Plus
download page for activation instructions.
• High sensitivity, high resolution (1600), and high image quality
achieved with the 4K-compatible newly developed MOS sensor and
image processing engine.
Furthermore, recording scenes in a variety of situations is made
possible with the 20x optical zoom lens, image stabilization and night
mode functions, Low Pass Filter to reduce moiré effects, and image
plane phase-difference detection AF (PDAF)*2which achieves AF that
reduces hesitation by being fast and precise.
*2PDAF: Phase Detection Auto Focus
• This product is compatible with High Bandwidth NDI (hereafter, NDI)
and NDI|HX technology of NewTek, Inc.
The problem of IP transmission delay and image degradation of
NDI|HX will be resolved with High Bandwidth NDI.
• Still image precision has been improved for Pan/Tilt by the inclusion of
a newly developed optical encoder.
• The unit supports transmission of video to NewTek High Bandwidth
NDI and NDI|HX compatible software applications and hardware
devices over a network.
• By connecting a controller, smooth camera operation via IP control is
made possible.
• The unit features a night mode that exposes subjects to infrared rays,
making it possible to shoot even under low-light conditions.
• When the unit is connected to a personal computer via an IP network,
it can be operated via a web browser.
• Equipped with a variety of 4K interfaces and also with multiple 3G-SDI
outputs individually fitted, this camera can flexibly adapt to a wide
range of applications as a remote camera compatible with 4K.
• The unit is available in pearl white (AW-UE160WP/AW-UE160WPC/
AW-UE160WE/AW-UE160WED) or black (AW-UE160KP/
AW-UE160KPC/AW-UE160KE/AW-UE160KED) to suit your intended
application and environment.
Computer requirements
CPU 7th Generation Intel®Core™ (Kaby Lake or later)
recommended
Memory For Windows:
4 GB or more
For Mac:
4 GB or more
Network function 100BASE-T/TX or 1000BASE-T,
RJ-45 connector
Image display Resolution: 1920 × 1080 pixels or more
Color generation: True Color 24-bit or more
Supported operating
systems and
web browsers
For Windows:
Microsoft®Windows®10
Microsoft Edge
Google Chrome
For Mac:
macOS13
macOS12
Safari
Google Chrome
For iPhone, iPad:
iOS
Safari
iPadOS
For Android:
Android OS
Google Chrome
Other Adobe®Reader®
(for viewing the operating instructions available on
the website)
10

IMPORTANT
• Failure to provide the required personal computer
environment may slow down the delineation of the images on
the screen, make it impossible for the web browser to work
and cause other kinds of problems.
<NOTE>
• Depending on the software version of the unit, an update may be
necessary.
• For the latest information on compatible operating systems and web
browsers, visit the support page at the following website.
https://pro-av.panasonic.net/en/
Disclaimer of warranty
IN NO EVENT SHALL Panasonic Connect Co., Ltd. BE LIABLE TO
ANY PARTY OR ANY PERSON, EXCEPT FOR REPLACEMENT
OR REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE
CASES, INCLUDING BUT NOT LIMITED TO BELOW:
AANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION,
DIRECT OR INDIRECT, SPECIAL, CONSEQUENTIAL OR
EXEMPLARY, ARISING OUT OF OR RELATING TO THE
PRODUCT;
BPERSONAL INJURY OR ANY DAMAGE CAUSED BY
INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE
USER;
CUNAUTHORIZED DISASSEMBLE, REPAIR OR MODIFICATION
OF THE PRODUCT BY THE USER;
DINCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES
ARE NOT DISPLAYED, DUE TO ANY REASON OR CAUSE
INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;
EANY PROBLEM, CONSEQUENTIAL INCONVENIENCE,
OR LOSS OR DAMAGE, ARISING OUT OF THE SYSTEM
COMBINED BY THE DEVICES OF THIRD PARTY;
FANY DEMANDS FOR COMPENSATION, CLAIMS, ETC.
OCCASIONED BY THE INFRINGEMENT OF PRIVACY BY
INDIVIDUALS OR ORGANIZATIONS WHOSE IMAGES WERE
SHOT BY THE USER BECAUSE THESE IMAGES (INCLUDING
THE RECORDINGS MADE) WERE MADE AVAILABLE BY THE
USER BECAUSE IN THE PUBLIC DOMAIN FOR SOME REASON
OR OTHER OR BECAUSE THE IMAGES ENDED UP BEING
USED FOR PURPOSES OTHER THAN THE ONE DESCRIBED
ABOVE;
GLOSS OF REGISTERED DATA CAUSED BY ANY FAILURE.
Network security
As the unit intended to be used while connected to a network, the
following security risks exist.
ALeakage or theft of information through the unit
BUnauthorized operation of the unit by persons with malicious intent
CInterference with or stoppage of the unit by persons with malicious
intent
It is your responsibility to take precautions, such as those described
below, to protect yourself against the above network security risks.
Panasonic does not accept any responsibility for damage of this type.
• Use the unit in a network secured by a firewall, etc.
• If the unit is connected to a network that includes personal computers,
make sure that the system is not infected by computer viruses or other
malicious programs (using a regularly updated antivirus program, anti-
spyware program, etc.).
• Protect your network against unauthorized access by restricting users
to those who log in with an authorized user name and password.
• After accessing the unit as an administrator, be sure to close all web
browsers.
• Change the administrator password periodically.
• To avoid passwords that can be guessed easily by third parties,
set a password of at least 8 characters in length, including at least
3 different types of characters, such as upper case, lower case,
numbers, and symbols.
• Restrict access to the unit by authenticating the users, for example,
to prevent setting information stored on the unit from leaking over the
network.
• Do not install the unit in locations where the unit, cables, and other
parts can be easily damaged or destroyed by persons with malicious
intent.
• Avoid connections that use public lines.
<NOTE>
Notes on user authentication
• User authentication on the unit can performed via digest authentication
or basic authentication. If basic authentication is used without the use
of a dedicated authentication device, password leaks may occur.
We recommend using digest authentication or host authentication.
Usage restrictions
• We recommend connecting the unit, controller, and any computers to
the same network segment.
Events based on settings inherent to the network devices, for example,
may occur in connections that include different segments, so be sure
to perform checks prior to operation.
• When using a Panasonic controller (AW-RP150, AW-RP60), set
[Wait time mode] to [Mode2] when using digest authentication.
(→ page 167)
Smooth operation may be diminished when [Wait time mode] is set to
[Mode1].
11
Before use (continued)

 Compatible with 4K/HD formats
• You can switch between the following formats via the camera
menus or a web browser.
[4K format]
2160/60p, 2160/59.94p, 2160/50p, 2160/29.97p*1 , 2160/25p*1 ,
2160/24p*1 , 2160/23.98p*1
[HD format]
1080/119.88p, 1080/100p, 1080/60p, 1080/59.94p, 1080/50p,
1080/29.97p*1 , 1080/25p*1 , 1080/24p*1 , 1080/23.98p*1 ,
1080/59.94i, 1080/50i, 720/59.94p, 720/50p
*1Native output
 Equipped with 1‑inch*24K new MOS sensor
and new image engine
• Equipped with a large, newly developed 1-inch*24K MOS sensor
that achieves F11/2000lx [Normal] and F14/2000lx [Low Light]
sensitivity. Low-noise recording made possible even in low-light
conditions.
*2Effective size
 Fitted with a wide‑angle optical zoom lens,
horizontal to 75.1°, and magnification to
20 times
• The entire subject can be taken widely even if the camera is close
to the subject.
• Even subjects far away can be captured clearly.
 Easy operation of unit enabled by its
integration with a high‑performance pan‑tilt
head unit
• Operations at the high speed of 180°/s
• With a pan range of ±175° and a tilt range of between –30° to
210°, the camera supports a wide range of movement.
• Quiet operation under noise level NC35 is possible (under NC25
during pan/tilt pause).
• Storage of up to 100 positions in the preset memory
 Built‑in night mode
• The unit supports infrared shooting.
By exposing subjects to infrared rays, shooting under ordinarily
difficult low-light conditions is possible.
(Image output will be in black and white.)
• The iris will be fixed at open.
 IP image output functions
• The unit is equipped with image compression and IP transmission
LSI capabilities. Output in 4K quality at up to 60 fps.
• Compatible as standard with SRT (Secure Reliable Transport)
and High bandwidth NDI/NDI|HX to enable the secure transfer
of images at high quality and low-latency even over public
telecommunications lines.
• Operation with IP control allows for a wide range of applications,
such as controlling the camera from remote locations.
 Compatible with the FreeD protocol, enabling
the building of an AR/VR system
• By outputting commands that conform with the FreeD protocol, it
is possible to connect with an AR/VR system.
• Camera tracking data (pan and tilt, zoom, focus, iris) is output
together with synchronizing signals, making it possible to easily
build a system without an encoder.
<NOTE>
• FreeD is a protocol for outputting the camera tracking data for AR/
VR systems.
 Equipped with PDAF (Phase Detection Auto
Focus) functionality
• Employing a method of combining image plane phase-difference
detection AF and contrast AF, we have achieved a new AF that is
fast and precise, with reduced hesitation.
 Equipped with HFR (High Frame Rate)
functionality
• Performing high-speed recording at FHD/120fps makes it possible
to record slow motion video that is both smooth and attractive.
 Equipped with Low Pass Filter as standard
• The optical Low Pass Filter greatly reduces the moiré effects
apparent on LED/LCD panels during recording.
 Compatible with SMPTE ST2110
• This is a specification for high-quality IP transmission of images
for use in the production of broadcast images. The camera can
support up to 2K/60p uncompressed transmission if you purchase
an optional software key (AW-SFU60) and optical transceiver
(commercially available).
Use EasyIP Setup Tool Plus to activate AW-SFU60. Refer to the
operating instructions available on the EasyIP Setup Tool Plus
download page for activation instructions.
 Equipped with XLR connectors (2ch) for audio
input
• There are two channels so that you can use high performance
microphones on either side of a venue for audio input. This gives
you the capability of recording in places such as live houses and
theaters where acoustics are valued.
 Easy connections and settings courtesy of IP
control
• Up to two hundred units can be operated by IP connection from a
Panasonic controller (AW-RP150, AW-RP60).
(The maximum length of the LAN cables is 100 meters (328 ft).)
• Network connection with AW-RP150 or AW-RP60 requires setup
of an initial account. (→ page 34)
When an initial account is not set up, AW-RP150 or AW-RP60 can
detect but cannot control this unit.
• When using a Panasonic controller (AW-RP150, AW-RP60), set
[Wait time mode] to [Mode2] when using digest authentication.
(→ page 167)
Smooth operation may be diminished when [Wait time mode] is
set to [Mode1].
Features
12


Use of easy‑to‑operate wireless remote control
(optional accessory) is possible
• A wireless remote control capable of operating up to four units can
be used.
It can easily be used to set the various functions or switch
between them while viewing the menu screens.
 Flexible camera layout enabled by simple
connection and installation
• This unit features excellent connectivity and installability thanks
to the IP control; a lightweight main unit, and the turn-lock
mechanism, which enables the user to install it on his or her own
(only when used indoors).
<NOTE>
• Bear in mind that this unit is designed to be used indoors only:
It cannot be used outdoors.
 PoE++ *1eliminates need for camera power
configurations
• Configurations for camera's power supply are not necessary when
the unit is connected to a network device that supports the PoE++
standard (IEEE 802.3bt compliant)*2.
Software authentication (LLDP) is also supported, but it may be
necessary to make settings on the network device (IEEE 802.3bt
compliant)*2.
<NOTE>
• If the external DC power supply and a PoE++ power supply are
connected simultaneously, the external DC power supply will have
priority. If the external DC power supply is disconnected while both
power supplies are connected, the unit will restart automatically,
and the image will be interrupted.
• Use a Category 5e cable or higher when using a PoE++ power
supply. The maximum length of the cable between the power
supply unit and the unit is 100 meters (328 ft). Using a cable that
is lower than Category 5e may result in reduced power supply
capabilities.
*1Power over Ethernet Plus Plus. Referred to as "PoE++" in this
manual.
*2For details on PoE++ power supply devices for which operation
has been verified, consult your local dealer.
13
Features (continued)

Accessories
Check that the following accessories are present and accounted for.
• After removing the product from its container, dispose of the power cable cap (if supplied) and packing materials in an appropriate manner.
Mount bracket for installation surface
(Hanging/Desktop) (1)
Main unit mounting screw (with flat
washer, spring washer)
M3×6 mm (1/4 inches) (1)
Drop‑prevention wire (1)
Drop‑prevention wire mounting screw (1)
(comes attached to the unit)
Bracket mounting screws (bind‑head)
M4×10 mm (13/32 inches) (6)
Lens cap (1)
(comes attached to the unit)
How to remove the lens cap
Move the lens cap in the direction of the arrow to remove.
Optional accessories
z Wireless remote control AW‑RM50AG (Size “AA” dry battery x 2, obtained separately)
<NOTE>
• For details on optional accessories, refer to the catalog or consult your local dealer.
14

 Do not use the unit in oily‑smoky or dusty
places.
Performance may be adversely affected if small particles or other
foreign objects get inside the product.
Take extra care in environments where a special effect such as
theatrical smoke is used.
 Do not allow foreign matter to make contact
with the rotating parts.
Failure to obey may cause the unit to malfunction.
 Maintenance
Turn off the unit’s power before proceeding with maintenance.
Failure to obey may result in injuries.
Wipe the surfaces using a soft dry cloth. Avoid all contact with
benzine, paint thinners and other volatile substances, and avoid
using these substances. Otherwise, the casing may become
discolored.
 Hold the bottom surface with both hands for
picking up this unit.
If you hold the lens part or the sides, it will put a load strain on the
motor and cause a malfunction.
 Do not turn the camera head by hand.
Turning the camera head by hand may cause the unit to
malfunction.
 About the lens/pan‑tilt head
If the lens, pan-tilt head, and other parts are not operated for a long
period of time, the viscosity of the grease applied inside them may
increase and operation may become no longer possible. Move the
lens and pan/tilt head regularly.
 Shoot under the proper lighting conditions.
To produce pictures with eye-pleasing colors, shoot under the
proper lighting conditions.
The pictures may not appear with their proper colors when shooting
under fluorescent lights. Select the proper lighting as required.
 To ensure a stable performance in the long
term
Using the unit for prolonged periods in locations where the
temperature and humidity levels are high will cause its parts to
deteriorate, resulting in a reduction of its service life.
(Recommended temperature: Max. 35 °C (95 °F))
Ensure that a cooling unit or heating unit will not blow any air
directly toward the installation location.
 Do not point the camera at
strong lights.
When parts of the MOS sensor are
exposed to spotlights or other strong
lights, blooming (a phenomenon where
the edges of strong lights become
blurred) may occur.
Bright subject
Blooming
 What happens with high‑brightness subjects
Flare may occur if an extremely bright light source is pointed at
the lens. In a case like this, change the angle or take some other
remedial action.
 When using the automatic functions
• In the “Scene” such as the camera menu, the initial settings on
some items has been set to auto, making it impossible for these
items to be operated manually. To operate them manually, switch
from the auto settings to the manual settings as required.
• When using the ATW (auto tracking white adjustment) function
under fluorescent lights, the white balance may vary.
• In some situations, it may be hard to focus at the auto setting. In
cases like this, select the manual setting, and focus manually.
 Zooming and focusing
When the focus is set manually, out-of-focusing may occur during
zooming.
After zooming, if necessary, either adjust the focus or set the focus
to auto.
When using the focus at the manual setting, proceed with zooming
after setting the focus position at the Tele end where the focusing
accuracy is higher. (However, if the distance from the unit to the
subject is less than 1.2 meters (3.9 ft), the subject may shift out of
focus at the Wide end.)
If zooming is performed to the Tele end after having adjusted the
focus at the Wide end, out-of-focusing may occur.
 Operation of the lens when the power is turned
on
When the unit’s power is turned on, the zoom, focus and iris are
adjusted automatically.
 The unit comes with the safe mode.
The safe mode is function designed to protect the unit from damage.
For details, refer to “Concerning the safe mode” (→ page 196).
 Concerning the HDMI interface standard
This unit has been certified as HDMI-compatible, but on rare
occasions images may not be displayed depending on the HDMI
device which has been connected to the unit.
 Concerning USB
Use a USB cable conforming to the USB3.0 specification. We also
recommend using a cable that is 1.5 m (4.9 ft) or shorter.
Operation is not guaranteed with a cable for USB2.0. This unit will
need to be restarted if one is connected by mistake.
 Color bars
Color bars are used to adjust the color phase, and the widths and
positions of these bars may differ from other models.
 H.264/H.265 patent pool licensing
This product is licensed based on the AVC Patent Portfolio License,
and the license does not extend beyond uses by users, who engage
in the acts described below, for their own personal and non-profit
applications.
(i) Recording of image information in compliance with the AVC
standard (hereafter, “AVC videos”)
(ii) Playing of AVC videos recorded by consumers engaging
in personal activities or AVC videos acquired from licensed
providers
For details, visit MPEG LA, LLC website (http://www.mpegla.com).
Operating precautions
15

 Concerning PoE++ power supply
The unit complies with the IEEE 802.3bt.
Use a compatible Ethernet hub and PoE++ injector to use a PoE++
power supply.
Software authentication (LLDP) complies with IEEE 802.3bt, but it
may be necessary to make settings on the network device.
For details on Ethernet hubs and PoE++ injectors for which
operations have been verified, consult your local dealer.
 Turn off the power before connecting or
disconnecting the cables.
This unit is not equipped with a power switch.
Turn off the DC 12 V power supply or PoE++ power supply device
before connecting or disconnecting cables.
 When the unit is not in use
Turn off the unit’s power when it is not in use.
When the unit is no longer going to be used, do not leave it lying
around, but be absolutely sure to dispose of it properly.
 Do not touch the optical system parts.
The optical system parts are vital to the operation of the camera.
Under no circumstances must they be touched.
In the unlikely event that they have become dusty, remove the
dust by using a camera blower or by wiping them gently with a lens
cleaning paper.
 Do not point the camera directly at the sun or a
laser beam no matter whether it is turned on or
not.
Taking images of the sun, laser beams, or other brightly lit subjects
for prolonged periods of time may damage the CCD.
 Personal computer used
If the same image is displayed for a prolonged period on a personal
computer's monitor, the monitor may be damaged. Use of a screen
saver is recommended.
 Concerning the IP address setting
Do not use EasyIP Setup Tool Plus on multiple personal computers
to simultaneously set the IP address for a single camera.
Otherwise, you will be unable to complete the proper procedure and
set the IP address correctly.
 Disposal of the unit
When the unit has reached the end of its service life and is to be
disposed of, ask a qualified contractor to dispose of the unit properly
in order to protect the environment.
 Moving the unit
• When carrying the unit, take care not to apply strong shocks or
drop it.
• Remove connection cables when moving the unit.
• Turn off the system power when moving the unit.
• Wrap the unit in cushioning material, etc., when moving the unit so
that impacts do not damage it.
• Treat the unit carefully so that vibrations or impacts do not
damage it.
 Concerning the installation location
Install the unit in a stable location which will not be susceptible to
shaking. If the unit is installed in a location which is susceptible to
shaking, this will cause the unit’s images to shake in turn.
Install the unit after conferring in detail with your dealer.
Install the unit on a ceiling that is strong enough (such as a concrete
ceiling).
If the unit is to be installed on a ceiling which is not strong enough,
reinforce the ceiling sufficiently first.
Install this unit in a stable location where it will not be shaken and
that has sufficient rigidity. Shaking of the installation location can
be the cause of performance deterioration and malfunctions in the
camera.
If the camera is installed in a location with insufficient stiffness,
the pan and tilt control characteristics may be adversely affected,
leading to unstable operation.
• In environments such as the following, there may be unusual
operation sounds during pan and tilt, and operational errors may
occur.
If you are concerned about unstable pan and tilt operations after
installation, please contact your dealer.
<Installation examples that may cause performance
deterioration and malfunctions>
Single point attachment to a cylindrical pole structure that has a
small diameter
Single point attachment to a movable structure
 
 Information on software used with this product
This product includes GNU General Public License (GPL) and GNU Lesser General Public License (LGPL) licensed software, and the customer is
entitled to obtain, modify, or redistribute the source code for the software.
This product includes MIT Licensed software.
This product includes BSD Licensed software.
For details on obtaining the source codes, visit the following website.
https://pro-av.panasonic.net/en/
However, do not contact Panasonic for questions regarding obtained source codes.
16
Operating precautions (continued)

This unit can be operated by remote control using a wireless
remote control (model number: AW‑RM50AG) purchased
separately.
Check out the following points before using the wireless remote
control.
z Point the wireless remote control at the unit’s wireless
remote control signal light‑sensing area (front panel or
back panel), and operate it within a range of 10 meters
(32.8 ft) from these areas.
z Refer to <Layout of wireless remote control signal
light‑sensing areas> on the right.
z The signal sensing distance is reduced if the angle at
which the wireless remote control signals are sensed is
increased.
The light-sensing sensitivity is reduced to about one-half when the
wireless remote control is pointed at an angle of 40 degrees from
each position in front of a wireless remote control signal light-sensing
area (front panel or back panel).
If the remote control is operated from the behind the unit, it may be
either difficult or impossible to perform the desired operations.
z If the unit is installed near fluorescent lights, plasma
monitors or other such products or if the unit is
exposed to sunlight, the effects of the light may make it
impossible for the unit to be operated using the wireless
remote control.
Be sure to follow the steps below for installation and use.
• Take steps to ensure that the wireless remote control signal light-
sensing area will not be exposed to the light from fluorescent lights,
plasma monitors or other such products or from the sun.
• Install the unit away from fluorescent lights, plasma monitors and
other such products.
z For about 10 minutes even after the batteries have been
removed from the wireless remote control, the selection
of the operation to be performed (the CAMERA <1> to
<4> button which was pressed last) will remain stored in
the memory.
When a longer period of time elapses, however, the
selection is reset to the status established when the
CAMERA <1> button was pressed.
<Layout of wireless remote control signal light‑sensing areas>
<NOTE>
• The arrows in the figure below show the light-sensing directions in
which the wireless remote control signals travel.
• Top view
• Rear panel view
Approx. 45° Approx. 45°
Wireless remote
control signal light‑
sensing area (back
panel, 1 place)
Wireless remote
control signal light‑
sensing area (front
panel, 2 places)
Wireless remote control (optional accessory)
17

Camera unit
LAN
LINK ACT
SIGNAL
GND
12 V IN
G/L IN
1 2/PM
3G SDI OUT
SFP+ 12G SDI OUT
USB3.0 HOST
RS-422
SERVICE
1 - AUDIO INPUT - 2
1
2
4
3
6
8
6
9
7
22
11 13 1412
2119
10
5
15
16 17 18 20
7
Rear panel
Bottom panel
1. Mount bracket for installation surface (supplied
accessory)
Mount this bracket onto the installation surface, and then attach the
camera main unit to the bracket.
2. Drop‑prevention wire
This wire is screwed down to the bottom panel of the camera main
unit. Loop the circle part of the wire around the hook of the mount
bracket.
3. Status display lamp
This lights in the following way depending on the status of the unit.
Orange Light up When the standby status is established
Blink twice When a signal not matched by the remote control
ID has been received from the wireless remote
control (optional accessory) while the power is on
Blinking
slowly
Firmware being updated (STEP 1: files being
transferred)
Blink three
times
rapidly
When the Identify function (a function that makes
the status display lamp of a specified camera
blink) of EasyIP Setup Tool Plus operates
Green Light up When the power is on
Blink twice When a signal matched by the remote control
ID has been received from the wireless remote
control (optional accessory) while the power is on
Blinking
rapidly
When the initialization process is complete
Red Light up When trouble has occurred in the unit
Blinking
slowly
Firmware being updated (STEP 2: data being
written)
Blinking
rapidly
When a PoE++ software authentication error has
occurred
4. Ventilation holes
Blocking the ventilation holes may cause a malfunction. Make sure
there is sufficient space around the ventilation holes.
5. Tilt head
This rotates in the right and left direction.
6. Wireless remote control signal light‑sensing area
The light-sensing area is provided in three places, on the front panel
of the camera pedestal and at the top of the rear panel.
7. Hole for securing the camera pedestal
This hole is provided in the bottom panel of the camera pedestal.
8. Camera head
This rotates in the up and down direction.
9. Tally lamp
These turn on/turn off with control signals only when the tally lamp
setting is “ON”. The tally lamps light in three different colors; red,
green, and yellow.
10.LAN connector for IP control <LAN LINK/ACT>
This LAN connector (RJ-45) is connected when exercising IP control
over the unit from an external device. Use a LAN cable (category 5e
or above, max STP 100 m (328 ft)) for connection.
Parts and their functions
18

11.Service switches <SERVICE>
Perform switch settings before turning the unit on.
LAN
LINK ACT
SIGNAL
GND
12 V IN
G/L IN
1 2/PM
3G SDI OUT
SFP+ 12G SDI OUT
USB3.0 HOST
RS-422
SERVICE
1 - AUDIO INPUT - 2
Service switches
Function Factory settings
SW1
Switches for initializing and initial settings
(Refer to the explanations in “Initialization 1”,
“Initialization 2”, “Direct start mode” )
OFF
SW2 OFF
SW3 OFF
SW4 OFF
Initialization 1
• Reset the user authentication settings and host authentication settings
for network connection.
(This will delete all the registered user information (IDs/passwords)
and host information (IP addresses).)
• With the service switches set as shown below, turn on the power of
the unit.
SW1
ON
OFF
SW2 SW3 SW4
<NOTE>
• When initialization is complete, the status display lamp on the front
of the unit blinks green. Set the service switches back to their original
positions (SW1 to SW4 all OFF), then restart the unit.
Initialization 2
• The unit is reset to the state it was in at the time of purchase. (All
camera menu setting values and network setting values are reset.)
• With the service switches set as shown below, turn on the power of
the unit.
SW1
ON
OFF
SW2 SW3 SW4
<NOTE>
• When initialization is complete, the status display lamp on the front
of the unit blinks green. Set the service switches back to their original
positions (SW1 to SW4 all OFF), then restart the unit.
• When initialization is complete, output images may be disrupted. When
you reset the service switches back to their original positions and
restart the unit, the image disruption should be resolved.
Direct start mode
• When the power of the unit is turned on, the pan-tilt head (tilt) is not
returned to horizontal as part of the lens initializing operation. Use
when the tilt cannot be returned to horizontal, such as when the unit is
installed in a tight space.
SW1
ON
OFF
SW2 SW3 SW4
<NOTE>
• This may result in a slight change in tracking performance.
12.
SFP connector <SFP+>
This is a connection terminal for an SFP+ optical fiber module. By
connecting the SFP+ optical fiber module, SMPTE ST2110*1or
SDI signals are output as converted optical signals. Select the fiber
module that matches the signal bandwidth*2for each format.
*1A separate optional software key (AW-SFU60) needs to be
purchased to enable SMPTE ST2110 functionality.
*2• 4K (60p, 59.94p, 50p): 12G
• 4K (other than 60p, 59.94p or 50p): 6G
• HD (60p, 59.94p, 50p): 3G
• HD (other than 60p, 59.94p or 50p): 1.5G
<NOTE>
• Optical signal input is not supported on this unit.
13.
12G SDI OUT connector <12G SDI OUT>
This is a 12G-SDI video signal output connector.
14.HDMI connector <HDMI>
This is the HDMI video output connector.
15.USB3.0 HOST connector <USB3.0 HOST>
Video transmission using wireless connections is made possible by
connecting a 5G mobile router (one that supports USB tethering)*3.
*3Use a product whose operation is guaranteed. For details, visit the
Panasonic website.
<NOTE>
• Refer to the catalog of the device you are using for usage times for
the 5G mobile router.
• Use a USB cable conforming to the USB3.0 specification. We also
recommend using a cable that is 1.5 m (4.9 ft) or shorter.
• Operation is not guaranteed with a cable for USB2.0. This unit will
need to be restarted if one is connected by mistake.
• A USB Type A – Type C adaptor may be required, depending on the
product to be connected.
16.DC IN connector <12V IN> (XLR connector)
Input 12 V DC.
<NOTE>
• Use a DC cable with the following lengths.
For 12 V input: Max. 3 m (9.84 ft) (when using an AWG16 cable)
External DC power supply
Connect after making sure that the output voltage of the external DC
power supply is compatible with the rated voltage of the camera.
Select an output amperage for the external DC power supply with a
margin above the total amperage of the connected devices.
The total amperage of connected devices can be calculated with the
following formula.
Total power consumption ÷ voltage
When the power of the camera is turned on, inrush current is generated.
Insufficient power supply when turning on the power may cause a
malfunction. We recommend that you use an external DC power supply
that can assure double the capacity of the total power consumption of the
camera and connected devices that are turned on by interlock when the
power of the camera is turned on (such as lenses, wireless microphone
receivers).
• Make sure of the pin alignment of the DC output terminal of the
external DC power supply and the camera DC IN connector, and
connect the polarity correctly.
If the +12 V power supply is mistakenly connected to the GND terminal,
it may cause fire or malfunction.
12 V IN
1
23
4
1 GND
2 —
3 —
4 +12 V
19
Parts and their functions (continued)

17.AUDIO IN connector <AUDIO INPUT 1, 2>
Inputs external audio (microphone, line).
AUDIO INPUT 1, 2
12
3
1 GND
2 AUDIO IN (H)
3 AUDIO IN (C)
18. 3G SDI OUT connector <3G SDI OUT 1, 2/PM>
This is an SDI video signal output connector. Depending upon the
output signal format, 3G-SDI or 1.5G-SDI signals are output.
When using SMPTE ST2110, if images are input to SFP+, then the
images input as RETURN signals can be output as from 3G SDI
OUT2/PM.
<NOTE>
• A separate optional software key (AW-SFU60) needs to be
purchased to enable SMPTE ST2110 functionality.
19. Ground connector
Connects to the ground connector on a wall outlet, ground bar, etc.
for grounding. (→ page 8)
20.G/L IN connector <G/L IN>
This is the external sync signal input connector.
This unit supports BBS (Black Burst Sync) and tri-level
synchronization.
Supply to this connector the signals that correspond to the video
signal format which has been set.
Frequency: 119.88 Hz
Format External sync signal input format
Tri‑level sync BBS
1080/119.88p
― ―
1080/59.94i
1080/29.97PsF
480/59.94i
Frequency: 100 Hz
Format External sync signal input format
Tri‑level sync BBS
1080/100p
― ―
1080/50i
1080/25PsF
576/50i
Frequency: 60 Hz
Format External sync signal input format
Tri‑level sync BBS
2160/60p
1080/60p
1080/60p
― ― ―
Frequency: 59.94 Hz, 29.97 Hz
Format External sync signal input format
Tri‑level sync BBS
2160/59.94p
― ―
1080/59.94i
1080/29.97PsF
480/59.94i
2160/29.97p
1080/59.94p
1080/29.97p
720/59.94p
― 720/59.94p ―
Frequency: 50 Hz, 25 Hz
Format External sync signal input format
Tri‑level sync BBS
2160/50p
― ―
1080/50i
1080/25PsF
576/50i
2160/25p
1080/50p
1080/25p
720/50p
― 720/50p ―
Frequency: 24 Hz
Format External sync signal input format
Tri‑level sync BBS
2160/24p 1080/24p 1080/24PsF
― ―
1080/24p
Frequency: 23.98 Hz
Format External sync signal input format
Tri‑level sync BBS
2160/23.98p 1080/23.98p 1080/23.98PsF
― ―
1080/23.98p
21.RS‑422 connector <RS‑422>
This RS-422 connector (RJ-45) is connected when exercising serial
control over the unit from an external device. Use a cable with the
following specifications for the connection to this connector.
Furthermore, by shorting the R-TALLY signal (2-pin) with the GND
(1-pin), it is possible to light the tally lamp (red) in the camera head
section of the unit.
<NOTE>
• Do not connect PoE cable to the RS-422 port.
• Do not apply a voltage to the R_TALLY_IN signal pin.
• Menu settings enable the output to pin 7 and pin 8 of the red tally
and green tally signals received by the unit. Output is by contact
output, and normally is “OPEN”, then it becomes “MAKE” for output.
(→ page 49, page 115)
• Control of this unit via the RS-422 connector (serial connection) is
not possible from Panasonic controllers (AW-RP150, AW-RP60).
To control this unit from Panasonic controllers (AW-RP150, AW-
RP60), control via the LAN connector (IP connection).
LAN cable*1(category 5e or above, straight cable),
max. 1000 m (3280 ft)
*1Use of an STP (shielded twisted pair) cable is
recommended.
Pin
No. Signal Pin
No. Signal
1 GND 5 TXD+
2 R_TALLY_IN 6 RXD+
3 RXD– 7
OPTION_OUT1
4 TXD– 8 OPTION_OUT2
20
Parts and their functions (continued)