Panasonic BL-MS103A User manual

ORDERNO.KMS0505068CE
F5
WirelessCameraMonitoringSystem
BL-MS103A
(forU.S.A.)
 2005PanasonicCommunicationsCo.,Ltd.Allrightsreserved.
Unauthorizedcopyinganddistributionisaviolationoflaw.
IMPORTANTINFORMATIONABOUTLEADFREE,(PbF),SOLDERING
Ifleadfreesolderwasusedinthemanufactureofthisproducttheprintedcircuitboardswillbemarked
PbF.
Standardleaded,(Pb),soldercanbeusedasusualonboardswithoutthePbFmark.
Whenthismarkdoesappearpleasereadandfollowthespecialinstructionsdescribedinthismanual
ontheuseofPbFandhowitmightbepermissibletousePbsolderduringserviceandrepairwork.
1.ABOUTLEADFREESOLDER(PbF:Pbfree)
1

Note:
Intheinformationbelow,Pb,thesymbolforleadintheperiodictableofelements,willrefertostandard
solderorsolderthatcontainslead.
WewillusePbFsolderwhendiscussingtheleadfreesolderusedinourmanufacturingprocesswhich
ismadefromTin,(Sn),Silver,(Ag),andCopper,(Cu).
Thismodel,andotherslikeit,manufacturedusingleadfreesolderwillhavePbFstampedonthePCB.
Forserviceandrepairworkwesuggestusingthesametypeofsolderalthough,withsomeprecautions,
standardPbsoldercanalsobeused.
Caution
-PbFsolderhasameltingpointthatis50°~70°F,(30°~40°C)higher
thanPbsolder.Pleaseuseasolderingironwithtemperaturecontrol
andadjustitto700°±20°F,(370°±10°C).Incaseofusinghigh
temperaturesolderingiron,pleasebecarefulnottoheattoolong.
-PbFsolderwilltendtosplashifitisheatedmuchhigherthanitsmelting
point,approximately1100°F,(600°C).
-IfyoumustusePbsolderonaPCBmanufacturedusingPbFsolder,
removeasmuchoftheoriginalPbFsolderaspossibleandbesurethat
anyremainingismeltedpriortoapplyingthePbsolder.
-WhenapplyingPbFsoldertodoublelayeredboards,pleasecheckthe
componentsideforexcesswhichmayflowontotheoppositeside(See
figure,below).
1.1.SUGGESTEDPbFSOLDER
ThereareseveraltypesofPbFsolderavailablecommercially.Whilethisproductismanufacturedusing
Tin,Silver,andCopper,(Sn+Ag+Cu),youcanalsouseTinandCopper,(Sn+Cu),orTin,Zinc,and
Bismuth,(Sn+Zn+Bi).Pleasecheckthemanufacturer’sspecificinstructionsforthemeltingpointsof
theirproductsandanyprecautionsforusingtheirproductwithothermaterials.Thefollowingleadfree
(PbF)solderwiregaugearerecommendedforserviceofthisproduct:0.3mm,0.6mmand1.0mm.
2

1.2.HOWTORECOGNIZETHATPbFREESOLDERISUSED
COMPONENTVIEW(BL-WV10A)
BOTTOMVIEW(BL-WV10A)
3

MAINBOARD(BL-C30A)
4

I/OBOARD(BL-C30A)
5

SUBBOARD(BL-C30A)
6

LENSBOARD(BL-C30A)
RFBOARD(BL-C30A)
7

2.FORSERVICETECHNICIANS
ICsandLSIsarevulnerabletostaticelectricity.
Whenreplacing,thefollowingprecautionswillhelptopreventrecurringmalfunctions.
1.Covertheplasticpartswithaluminumfoil.
2.Groundthesolderingirons.
8

3.Useaconductivematonthework-table.
4.DonotgraspICorLSIpinswithbarefingers.
3.CAUTION
3.1.SAFETYPRECAUTIONS
1.Beforeservicing,unplugthepowercordtopreventanelectricalshock.
2.Whenreplacingparts,useonlymanufacturer’srecommended
componentsforsafety.
3.Checktheconditionofpowercord.Replaceifwearordamageis
evident.
4.Afterservicing,besuretorestoretheleaddress,insulationbarriers,
insulationpapers,shields,etc.
5.Beforereturningtheservicedequipmenttothecustomer,makethe
followinginsulationresistancetesttopreventashockhazard.
3.2.BATTERYCAUTION
Dangerofexplosionifthebatteryisreplacedincorrectly.Replaceonlywiththesameorequivalenttype
recommendedbythemanufacturer.Discardusedbatteriesaccordingtofollowingcaution:
Disposalortransportationoflithiumbatteriesshouldbeperformedbypermitted,inaccordancewith
federal,stateandlocalguidelines.
Abatterycontinuestohavenotransportationlimitationsaslongasitisseparatedtopreventshort
circuitsandpackedinstrongpackaging.
Commercialfirmsthatdisposeofanyquantityoflithiumcellsshouldhaveamechanisminplaceto
accountfortheirultimatedisposition.Thisisagoodpracticeforalltypesofcommercialorindustrial
waste.
Whenthelithiumbatteryisexchanged,theclocksettingsarecleared.Inthiscase,makeclocksettings
again.
RecommendTypeNumber:
CR-1632/1HF(BAT1)ManufacturedbyMATSUSHITA
3.3.TRADEMARKS
-AdobeandAcrobatareeitherregisteredtrademarksortrademarksof
AdobeSystemsIncorporatedintheUnitedStatesand/orother
countries.
-EthernetiseitheraregisteredtrademarkoratrademarkofXerox
CorporationintheUnitedStatesand/orothercountries.
9

-Microsoft,Windows,HotmailandActiveXareeitherregistered
trademarksortrademarksofMicrosoftCorporationintheUnitedStates
and/orothercountries.
-PentiumisatrademarkorregisteredtrademarkofIntelCorporationor
itssubsidiariesintheUnitedStatesandothercountries.
-ScreenshotsreprintedwithpermissionfromMicrosoftCorporation.
-Allothertrademarksidentifiedhereinarethepropertyoftheirrespective
owners.
3.4.INSULATIONRESISTANCETEST
1.UnplugtheACpowercordandshortthetwoprongsoftheplugwitha
jumperwire.
2.MeasuretheresistancevaluewithohmmeterbetweenthejumperedAC
plugandeachexposedmetalcabinetpart,suchasscrewthreads,etc.
Note:
Someexposedpartsmaybeisolatedfromthechassisbydesign.Thesewillreadinfinity.
3.Ifthemeasurementisoutsidethespecifiedlimits,thereisapossibility
ofshockhazard.Theequipmentshouldberepairedandrechecked
beforeitisreturnedtothecustomer.
10