Panasonic DMC-TS25R Installation and service instructions

Basic Owner’s Manual
Digital Camera
Model No. DMC-TS25
Please read these instructions carefully before using this
product, and save this manual for future use.
Register online at www.panasonic.com/register
(U.S. customers only)
More detailed instructions on the
operation of this camera are
contained in “Owner’s Manual for
advanced features (PDF format)” in the supplied
CD-ROM. Install it on your PC to read it.
until
2012/12/31
VQT4N50
F1112YS0
P
For USA and Puerto Rico assistance, please call: 1-800-211-PANA(7262) or,
contact us via the web at: http://www.panasonic.com/contactinfo
DMC-FT25&TS25P-VQT4N50_eng.book 1 ページ ２０１２年１１月１９日 月曜日 午前１１時５分

VQT4N50 (ENG)
2
Dear Customer,
Thank you for choosing Panasonic!
You have purchased one of the most sophisticated and reliable products on the market
today. Used properly, we’re sure it will bring you and your family years of enjoyment.
Please take time to fill in the information on the below. The serial number is on the tag
located on the underside of your camera. Be sure to retain this manual as your
convenient camera information source.
Please note that the actual controls and components, menu items, etc. of your Digital
Camera may look somewhat different from those shown in the illustrations in this
Owner’s Manual.
Carefully observe copyright laws.
•Recording of pre-recorded tapes or discs or other published or broadcast material for
purposes other than your own private use may infringe copyright laws. Even for the purpose
of private use, recording of certain material may be restricted.
-If you see this symbol-
A lithium ion battery that is recyclable powers the product you have
purchased. Please call 1-800-8-BATTERY for information on how
to recycle this battery.
Information on Disposal in other Countries outside
the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your
local authorities or dealer and ask for the correct
method of disposal.
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
Serial No.
DMC-FT25&TS25P-VQT4N50_eng.book 2 ページ ２０１２年１１月１５日 木曜日 午前１０時４４分

3
(ENG) VQT4N50
Information for Your Safety
∫Product identification marking
WARNING:
To reduce the risk of fire, electric shock or product damage,
•Do not let water or other liquids drip or splash inside the unit.
•Do not expose accessories (battery pack, battery charger, AC adaptor, SD memory
card and etc.) to rain, moisture, dripping or splashing.
•Use only the recommended accessories.
•Do not remove covers.
•Do not repair this unit by yourself. Refer servicing to qualified service personnel.
The socket outlet shall be installed near the equipment and shall be easily
accessible.
Product Location
Digital Camera Bottom
Battery Charger Bottom
DMC-FT25&TS25P-VQT4N50_eng.book 3 ページ ２０１２年１１月１５日 木曜日 午前１０時４４分

VQT4N50 (ENG)
4
FCC Note:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
•Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, follow the attached installation
instructions and use only shielded interface cables with ferrite core when connecting
to computer or peripheral devices.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
Declaration of Conformity
Trade Name: Panasonic
Model No.: DMC-TS25
Responsible Party: Panasonic Corporation of North America
One Panasonic Way, Secaucus, NJ 07094
Support Contact: Panasonic Consumer Marketing Company of North America
1-800-211-PANA (7262)
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
DMC-TS25
DMC-FT25&TS25P-VQT4N50_eng.book 4 ページ ２０１２年１１月１５日 木曜日 午前１０時４４分

5
(ENG) VQT4N50
∫About the battery pack
•Do not heat or expose to flame.
•Do not leave the battery(ies) in a car exposed to direct sunlight for a long period of time with
doors and windows closed.
CAUTION
Battery pack (Lithium ion battery pack)
•Use the specified unit to recharge the battery pack.
•Do not use the battery pack with equipment other than the specified unit.
•Do not get dirt, sand, liquids, or other foreign matter on the terminals.
•Do not touch the plug terminals (iand j) with metal objects.
•Do not disassemble, remodel, heat or throw into fire.
If any electrolyte should come into contact with your hands or clothes, wash it off
thoroughly with water.
If any electrolyte should come into contact with your eyes, never rub the eyes. Rinse
eyes thoroughly with water, and then consult a doctor.
CAUTION
•Danger of explosion if battery is incorrectly replaced. Replace only with the type
recommended by the manufacturer.
•When disposing the batteries, please contact your local authorities or dealer and ask for
the correct method of disposal.
Warning
Risk of fire, explosion and burns. Do not disassemble, heat above 60 xC (140 oF) or
incinerate.
DMC-FT25&TS25P-VQT4N50_eng.book 5 ページ ２０１２年１１月１５日 木曜日 午前１０時４４分

VQT4N50 (ENG)
6
∫About the battery charger
∫Cautions for Use
•Do not use any other USB connection cables except the supplied one or a genuine
Panasonic USB connection cable (DMW-USBC1: optional).
•Always use a genuine Panasonic AV cable (DMW-AVC1: optional).
Keep this unit as far away as possible from electromagnetic equipment (such as
microwave ovens, TVs, video games etc.).
•If you use this unit on top of or near a TV, the pictures and/or sound on this unit may be
disrupted by electromagnetic wave radiation.
•Do not use this unit near cell phones because doing so may result in noise adversely
affecting the pictures and/or sound.
•Recorded data may be damaged, or pictures may be distorted, by strong magnetic fields
created by speakers or large motors.
•Electromagnetic wave radiation generated by microprocessors may adversely affect this unit,
disturbing the pictures and/or sound.
•If this unit is adversely affected by electromagnetic equipment and stops functioning properly,
turn this unit off and remove the battery or disconnect AC adaptor (DMW-AC5PP: optional).
Then reinsert the battery or reconnect AC adaptor and turn this unit on.
Do not use this unit near radio transmitters or high-voltage lines.
•If you record near radio transmitters or high-voltage lines, the recorded pictures and/or sound
may be adversely affected.
CAUTION!
To reduce the risk of fire, electric shock or product damage,
•Do not install or place this unit in a bookcase, built-in cabinet or in another
confined space. Ensure this unit is well ventilated.
Battery charger
This battery charger operates on AC between 110 V and 240 V.
But
•In the U.S.A. and Canada, the battery charger must be connected to a 120 V AC power
supply only.
•When connecting to an AC supply outside of the U.S.A. or Canada, use a plug adaptor to
suit the AC outlet configuration.
DMC-FT25&TS25P-VQT4N50_eng.book 6 ページ ２０１２年１１月１５日 木曜日 午前１０時４４分

7
(ENG) VQT4N50
Contents
Information for Your Safety......................................................................................... 3
Before Use .................................................................................................................... 8
Standard Accessories ................................................................................................. 9
(Important) About the Waterproof/Dustproof and Anti-shock Performance
of the Camera ............................................................................................................. 10
Names and Functions of Main Parts ........................................................................ 15
Charging the Battery.................................................................................................. 16
Inserting and Removing the Card (optional)/the Battery ....................................... 17
Sequence of operations ............................................................................................ 18
Reading the Owner’s Manual (PDF format) ............................................................. 20
Installing supplied software...................................................................................... 21
Specifications............................................................................................................. 22
Digital Camera Accessory System........................................................................... 25
Digital Camera Accessory Order Form.................................................................... 26
Limited Warranty (ONLY FOR U.S.A. AND PUERTO RICO) ................................... 27
DMC-FT25&TS25P-VQT4N50_eng.book 7 ページ ２０１２年１１月１５日 木曜日 午前１０時４４分

VQT4N50 (ENG)
8
Before Use
•Do not apply strong shock or vibration by dropping or knocking the camera. Also, do
not apply strong pressure to the camera.
–Waterproof performance may be impaired.
–Lens or LCD monitor may be damaged.
–It may cause malfunction in the performance or the function.
∫When inner side of the lens is fogged (condensation)
It is not a malfunction or failure of the camera. It may be
caused by the environment in which the camera is used.
What to do when inner side of the lens is fogged
•Turn off the power and open the side door in a place with constant
ambient temperature, away from high temperatures, humidity,
sand and dust. The fog will disappear naturally in 10 minutes to
2 hours with the side door open when the temperature of the
camera gets close to the ambient temperature.
•Contact Panasonic if the fogging does not disappear.
Conditions in which inner side of the lens may be fogged
Condensation may occur and the inner side of the lens may be fogged when the
camera is used in areas that undergo a significant change in temperature or in high
humidity, such as the following:
•When the camera is used underwater suddenly after being on a hot beach etc.
•When the camera is moved to a warm area from a cold area, such as at a ski resort or
at high altitude
•When the side door is opened in a high-humidity environment
Please be sure to read “(Important) About the Waterproof/Dustproof and Anti-shock
Performance of the Camera”(P10) before using this unit underwater to prevent the
unit from being mishandled, which may cause water to seep in.
DMC-FT25&TS25P-VQT4N50_eng.book 8 ページ ２０１２年１１月１５日 木曜日 午前１０時４４分

9
(ENG) VQT4N50
Standard Accessories
Check that all the accessories are supplied before using the camera.
Product numbers correct as of January 2013. These may be subject to change.
1 Battery Pack
(Indicated asbattery pack orbattery in
the text)
Charge the battery before use.
2 Battery Charger
(Indicated as battery charger or
charger in the text)
3 USB Connection Cable
4 CD-ROM
•Software
•Owner’s Manual for advanced features
Install on your PC before use.
5 Hand Strap
•Supplied accessories are not waterproof.
•SD Memory Card, SDHC Memory Card and
SDXC Memory Card are indicated as card in
the text.
•The card is optional.
You can record or play back pictures on the
built-in memory when you are not using a
card.
•For information about optional accessories, refer to the “Digital Camera Accessory System”.
•If any accessories are lost, customers should contact Panasonic’s parts department at
1-800-833-9626 for further information about obtaining replacement parts.
3
12
4
5
DMW-BCK7PP
VFF1079
DE-A91B
K1HY08YY0015
VFC4297
DMC-FT25&TS25P-VQT4N50_eng.book 9 ページ ２０１２年１１月１５日 木曜日 午前１０時４４分

VQT4N50 (ENG)
10
(Important) About the Waterproof/
Dustproof and Anti-shock Performance of
the Camera
This does not guarantee no destruction, no malfunction, or waterproofing in all
conditions.
¢1 This means that the camera can be used underwater for specified time in specified
pressure in accordance with the handling method established by Panasonic.
¢2 “MIL-STD 810F Method 516.5-Shock” is the test method standard of the U.S. Defense
Department, which specifies performing drop tests from a height of 122 cm (4 feet), at
26 orientations (8 corners, 12 ridges, 6 faces) using 5 sets of devices, and passing the
26 orientation drops within 5 devices. (If failure occurs during the test, a new set is used to
pass the drop orientation test within a total of 5 devices)
Panasonic’s test method is based on the above “MIL-STD 810F Method 516.5-Shock”.
However, the drop height was changed from 122 cm (4 feet) to 150 cm (5 feet) dropping
onto 3 cm (0.1 feet) thick plyboard. This drop test was passed.
(Disregarding appearance change such as loss of paint or distortion of the part where
drop impact is applied.)
Waterproof/Dustproof Performance
This camera’s waterproof/dustproof rating complies with the “IPX8” and
“IP6X” ratings. Provided the care and maintenance guidelines described in
this document are strictly followed, this camera can operate underwater, to a
depth not exceeding 7 m (23 feet) for a time not exceeding 60 minutes. (¢1)
Anti-shock Performance
This camera also complies with “MIL-STD 810F Method 516.5-Shock”. The
camera has cleared a drop test from a height of 1.5 m (5 feet) onto 3 cm
(0.1 feet) thick plywood. In most cases this camera should not sustain any
damage if dropped from a height not exceeding 1.5 m (5 feet). (¢2)
DMC-FT25&TS25P-VQT4N50_eng.book 10 ページ ２０１２年１１月１５日 木曜日 午前１０時４４分

11
(ENG) VQT4N50
∫Handling of the camera
•Waterproofing is not guaranteed if the unit is subject to an impact as a result of being hit or
dropped etc. If an impact to the camera occurs, it should be inspected (subject to a fee) by a
Panasonic to verify that the waterproofing is still effective.
•When the camera is splashed with detergent, soap, hot spring, bath additive, sun oil, sun
screen, chemical, etc., wipe it off immediately.
•Waterproof function of the camera is for sea water and fresh water only.
•Any malfunction caused by customer misuse, or mishandling will not be covered by the
warranty.
•The inside of this unit is not waterproof. Water leakage will cause malfunction.
•Supplied accessories are not waterproof.
•Card and battery are not waterproof. Do not handle with a wet hand. Also, do not insert wet
card or battery into the camera.
•Do not leave the camera for a long period of time in places where the temperature is very low
(such as at ski resorts or high altitudes) or where the temperature may exceed 40 ºC (104 oF)
(such as inside cars in strong sunlight, close to a heater, on boats, or on the beach).
(Waterproof performance may become degraded.)
∫About the [Precautions] demonstration display
([Requirements for Underwater use])
•[Precautions] is displayed when the power is turned on for the first time after purchase, with
the side door completely closed.
•Please check beforehand to maintain the waterproof performance.
1Press 2to select [Yes], and press [MENU/SET].
•It will automatically skip to the clock setting screen if [No] is selected before it starts.
2Press 2/1to select the picture.
•It can be forcefully ended by pressing [MENU/SET].
•When it is forcefully ended while checking by turning the unit off or pressing [MENU/
SET], [Precautions] is displayed every time the power is turned on.
3After the final screen (12/12), press [MENU/SET] to finish.
•When [MENU/SET] is pressed after the final screen (12/12), [Precautions] is not
displayed from the next time the power is turned on.
•This can also be viewed from [Precautions] in the [Setup] menu.
2: Return to the previous screen
1: View the next screen
DMC-FT25&TS25P-VQT4N50_eng.book 11 ページ ２０１２年１１月１５日 木曜日 午前１０時４４分

VQT4N50 (ENG)
12
1Check that there are no foreign objects on the inner side of the side door.
•If there is any foreign object, such as lint, hair, sand, etc., on the surrounding area,
water will leak within a few seconds causing malfunction.
•Wipe it off with a dry soft cloth if there is any liquid.
It may cause water leaks and malfunction if you use the camera with liquid adhered.
•If foreign objects are present, wipe them off with a dry, lint-free cloth.
•Be extremely careful to remove the small sand etc. that may adhere to the sides and
corners of the rubber seal.
2Check for cracks and deformation of the rubber seal on the side door.
•The integrity of the rubber seals may decrease after about 1 year, with use and age. To
avoid permanently damaging the camera, the seals should be replaced once each
year. Please contact Panasonic for related costs and other information.
3Close the side door securely.
A[LOCK] switch (gray part)
BRed part
CReleased state
DLocked state
•Lock the [LOCK] switch securely until
the red part is no longer visible.
•To prevent water intrusion, be careful
not to catch foreign objects such as
liquids, sand, hair, dust, or the strap
cord.
Check before using underwater
Always wipe the rubber seal on the side door and the area where rubber seal
sits with a dry, lint-free cloth.
Do not open or close the side door in places with sand and dust, close to water,
or with wet hands. Sand or dust adhering may cause water leaks.
ロヰヤレ
ロヰヤレ
ロヰヤレ
DMC-FT25&TS25P-VQT4N50_eng.book 12 ページ ２０１２年１１月１５日 木曜日 午前１０時４４分

13
(ENG) VQT4N50
•Use the camera underwater to 7 m (23 feet) with the water temperature between 0 oC and
40 oC (32 oF and 104 oF).
•Do not use for scuba diving (Aqualung).
•Do not use the camera at a depth of over 7 m (23 feet).
•Do not use it in the hot water over 40 oC (104 oF) (in the bath or hot spring).
•Do not use the camera underwater longer than 60 minutes continuously.
•Do not open or close the side door underwater.
•Do not apply shock to the camera underwater. (Waterproof performance may not be
maintained, and there is a chance of water leak.)
•Do not dive into the water holding the camera. Do not use the camera in a location where the
water will splash strongly, such as rapid flow or waterfall. (Strong water pressure may be
applied, and it may cause malfunction.)
•The camera will sink in the water. Take care not to drop the camera and lose it underwater by
securely placing the strap around your wrist or similar measure.
1Rinse with water with the side door closed.
•After use at the seaside or underwater, soak the unit in
fresh water pooled in a shallow container for
10 minutes or less.
•If the zoom button or camera [ON/OFF] button do not
press smoothly, it may be caused by an adhesion of
foreign objects. Using in such a state may cause
malfunctions, such as locking up, so wash off any
foreign objects by shaking the camera in fresh water.
•Bubbles may come out of the drainage hole when you
immerse the camera in water, but this is not a
malfunction.
Using the camera underwater
Caring of the camera after using it underwater
Do not open or close the side door until the sand and dust is removed by
rinsing the camera with water.
Make sure to clean the camera after using it.
•Thoroughly wipe off any water droplets, sand, and saline matter on your hands, body, hair,
etc.
•It is recommended to clean the camera indoors, avoiding places where water spray or
sand may fall.
After using it underwater, always clean the camera rather than leaving it in a
dirty state.
•Leaving the camera with foreign objects or saline matter on it may cause damage,
discoloration, corrosion, unusual odour, or deterioration of the waterproof performance.
DMC-FT25&TS25P-VQT4N50_eng.book 13 ページ ２０１２年１１月１９日 月曜日 午前１１時５分

VQT4N50 (ENG)
14
2Drain water by holding the camera upside-down Aand the right way up B
and shaking it lightly a few times.
•After using the camera at the beach or in water, or after washing it, water may remain
around the speaker and microphone for a while and may cause a drop in volume or
sound distortion.
•Make sure to put your hand through the strap to prevent the camera from falling.
3Wipe off water drops on the camera with a
soft, dry cloth and dry the camera in a
shaded area that is well ventilated.
•Dry the camera by standing it on a dry cloth.
This unit incorporates drain design, draining
water in gaps in the camera [ON/OFF] button
and zoom button etc.
•Do not dry the camera with hot air from dryer
or similar. Waterproof performance will
deteriorate due to deformation.
•Do not use chemicals such as benzine, thinner, alcohol or cleanser, soap or
detergents.
4Confirm that there are no water droplets, open the side door, and wipe off
any water droplets or sand left inside using a soft, dry cloth.
•Water droplets may adhere to the card or battery when the side door is opened without
thoroughly drying. Also, water may accumulate in the gap around the card/battery slot
or the terminal connector. Be sure to wipe any water off with a soft, dry cloth.
•The water droplets may seep into the camera when the side door is closed while it is
still wet, causing condensation or failure.
DMC-FT25&TS25P-VQT4N50_eng.book 14 ページ ２０１２年１１月１５日 木曜日 午前１０時４４分

15
(ENG) VQT4N50
Names and Functions of Main Parts
1Flash
2 Motion picture button
3 Shutter button
4 Camera [ON/OFF] button
5 Microphone
6 Self-timer indicator/
AF Assist Lamp/
LED light
7Lens
8 LCD monitor
9 [MODE] button
10 Zoom button
11 Strap eyelet
•Be sure to attach the strap when
using the camera to ensure that you
will not drop it.
12 Release lever
13 [LOCK] switch
14 Side door
15 [(] (Playback) button
16 [Q.MENU] button/[ ] (Delete/
Cancel) button
17 [DISP.] button
18 [MENU/SET] button
19 Cursor buttons
20 Speaker
•Be careful not to cover the speaker
with your finger. Doing so may make
sound difficult to hear.
21 Tripod mount
•A tripod with a screw length of 5.5 mm
(0.22 inch) or more may damage this
unit if attached.
22 [AV OUT/DIGITAL] socket
23 Card slot
24 Battery slot
•When using an AC adaptor, ensure
that the Panasonic DC coupler
(DMW-DCC10: optional) and AC
adaptor (DMW-AC5PP: optional) are
used.
•Always use a genuine Panasonic AC
adaptor (DMW-AC5PP: optional).
2134567891011
15
16
18 17
19
20 21
ャモヵヵユンヺ
モヷチヰヶヵバチュリヨリヵモロ
ヤモンュ
22
23
24
12
13
14
DMC-FT25&TS25P-VQT4N50_eng.book 15 ページ ２０１２年１１月１５日 木曜日 午前１０時４４分

VQT4N50 (ENG)
16
Charging the Battery
Use the dedicated charger and battery.
•The battery is not charged when the camera is shipped. Charge the battery before use.
•Charge the battery with the charger indoors [10 oC to 30 oC (50 oF to 86 oF)].
∫About batteries that you can use with this unit
The battery that can be used with this unit is DMW-BCK7PP.
Attach the battery paying attention to the
direction of the battery.
Connect the charger to the electrical
outlet.
•The [CHARGE] indicator Alights up and charging
begins.
∫About the [CHARGE] indicator
On: Charging.
Off: Charging has completed. (Charging time: Approx. 120 min)
DMC-FT25&TS25P-VQT4N50_eng.book 16 ページ ２０１２年１１月１５日 木曜日 午前１０時４４分

17
(ENG) VQT4N50
Inserting and Removing the Card
(optional)/the Battery
•Check that this unit is turned off.
•Confirm that there is no foreign object.
•We recommend using a Panasonic card.
1:Slide the [LOCK] switch A, and
release the lock.
2:Slide the release lever Band
open the side door.
•Always use genuine Panasonic batteries
(DMW-BCK7PP).
•If you use other batteries, we cannot
guarantee the quality of this product.
Battery: Being careful about the
battery orientation, insert all the
way until you hear a locking sound
and then check that it is locked by
lever C. Pull the lever Cin the
direction of the arrow to remove
the battery.
Card: Push it securely all the way
until you hear a “click” while being
careful about the direction in
which you insert it. To remove the card, push the card until it
clicks, then pull the card out upright.
D: Do not touch the connection terminals of the card.
Close the side door until it clicks,
and then lock the [LOCK] switch
by sliding it toward [2].
•Confirm that the red part on the [LOCK]
switch is not showing.
Note
•Keep the Memory Card out of reach of children to
prevent swallowing.
ロヰヤレ
ロヰヤレ
DMC-FT25&TS25P-VQT4N50_eng.book 17 ページ ２０１２年１１月１５日 木曜日 午前１０時４４分

VQT4N50 (ENG)
18
Sequence of operations
Press camera [ON/OFF] button.
•The clock is not set when the camera is
shipped. Set the date and time before
using the camera.
Press the shutter button halfway to
focus and then press it fully to take
the picture.
∫Selecting the Recording Mode
Press [MODE] to select the Recording Mode.
: Take pictures with automatic settings.
: Take pictures with your own settings.
: Record while checking the image effect.
: This mode is optimal for taking pictures of sporting events, etc.
: This mode is optimal for taking pictures that show thesnow as white as possible at
a ski resort or a snow-covered mountain.
: This mode is optimal for taking pictures to 3 m (10 feet) underwater and at the
beach.
: This mode is optimal for taking pictures at depths of 3 m (10 feet) to 7 m (23 feet).
: This mode allows you to take panorama pictures.
: Take pictures according to scene.
DMC-FT25&TS25P-VQT4N50_eng.book 18 ページ ２０１２年１１月１５日 木曜日 午前１０時４４分

19
(ENG) VQT4N50
∫Recording Motion Pictures
Start recording by pressing the motion picture button.
•Stop the recording by pressing the motion picture button again.
•Maximum time to record motion pictures continuously is 29 minutes 59 seconds.
The maximum available recording time continuously is displayed on the screen.
∫Setting the Menu
Press [MENU/SET] to display the menu screen to change the recording function,
camera settings, and other settings.
∫Playing Back Pictures
Press [(].
•Press 2or 1to select the picture.
∫Deleting Pictures
Select the picture, and then press [ ].
•Confirmation screen is displayed. Picture is deleted by selecting [Yes].
∫About the [LED Light] ([Setup])
If you set to [ ], and press and hold down 1(‰) on the
recording standby screen, the LED light will come on for
60 seconds.
DMC-FT25&TS25P-VQT4N50_eng.book 19 ページ ２０１２年１１月２０日 火曜日 午後４時４３分

VQT4N50 (ENG)
20
Reading the Owner’s Manual
(PDF format)
More detailed instructions on the operation of this camera are contained in
“Owner’s Manual for advanced features (PDF format)” in the supplied CD-ROM.
Install it on your PC to read it.
∫For Windows
Turn the PC on and insert the CD-ROM containing the Owner’s
Manual (supplied).
Click the [Owner’s Manual].
Select the desired language and
then click [Owner’s Manual] to
install.
ATo return to the install menu.
Double-click the “Owner’s Manual”
shortcut icon on the desktop.
∫When the Owner’s Manual (PDF format)
will not open
You will need Adobe Acrobat Reader 5.0 or later, or Adobe Reader 7.0 or later to
browse or print the Owner’s Manual (PDF format).
•You can download and install a version of Adobe Reader that you can use with your OS from
the following website.
http://get.adobe.com/reader/otherversions/
DMC-FT25&TS25P-VQT4N50_eng.book 20 ページ ２０１２年１１月１５日 木曜日 午前１０時４４分