Panasonic Lumix DMC-FT4 Technical specifications

Basic Operating Instructions
Digital Camera
Model No. DMC-FT4
Before use, please read these instructions completely.
More detailed instructions on the
operation of this camera are
contained in “Operating
Instructions for advanced features
(PDF format)” in the supplied CD-ROM. Install it
on your PC to read it.
EB
Web Site: http://www.panasonic-europe.com
VQT4E00
F0212HY0
Model number suffix “EB” denotes UK model.
until
2012/02/22
VQT4E00~Cover_mst.fm 1 ページ ２０１２年１月２４日 火曜日 午後１時５４分

VQT4E00 (ENG)
2
Dear Customer,
We would like to take this opportunity to thank you for purchasing this Panasonic Digital
Camera. Please read these Operating Instructions carefully and keep them handy for
future reference. Please note that the actual controls and components, menu items, etc.
of your Digital Camera may look somewhat different from those shown in the
illustrations in these Operating Instructions.
Carefully observe copyright laws.
•Recording of pre-recorded tapes or discs or other published or broadcast material for
purposes other than your own private use may infringe copyright laws. Even for the purpose
of private use, recording of certain material may be restricted.
Information for Your Safety
∫Product identification marking
WARNING:
To reduce the risk of fire, electric shock or product damage,
•Do not let water or other liquids drip or splash inside the unit.
•Do not expose accessories (battery pack, battery charger, AC adaptor, SD memory
card and etc.) to rain, moisture, dripping or splashing.
•Use only the recommended accessories.
•Do not remove covers.
•Do not repair this unit by yourself. Refer servicing to qualified service personnel.
The socket outlet shall be installed near the equipment and shall be easily
accessible.
Product Location
Digital Camera Bottom
Battery Charger Bottom
DMC-FT4&TS4EB-VQT4E00_mst.book 2 ページ ２０１２年１月２３日 月曜日 午前９時５２分

3
(ENG) VQT4E00
Caution for AC mains lead
For your safety, please read the following
text carefully.
This appliance is supplied with a moulded
three pin mains plug for your safety and
convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced
please ensure that the replacement fuse
has a rating of 5-ampere and that it is
approved by ASTA or BSI to BS1362.
Check for the ASTA mark or the BSI
mark on the body of the fuse.
If the plug contains a removable fuse
cover you must ensure that it is refitted
when the fuse is replaced.
If you lose the fuse cover the plug must
not be used until a replacement cover is
obtained.
A replacement fuse cover can be
purchased from your local dealer.
CAUTION!
IF THE FITTED MOULDED PLUG IS
UNSUITABLE FOR THE SOCKET
OUTLET IN YOUR HOME THEN THE
FUSE SHOULD BE REMOVED AND
THE PLUG CUT OFF AND DISPOSED
OF SAFELY.
THERE IS A DANGER OF SEVERE
ELECTRICAL SHOCK IF THE CUT OFF
PLUG IS INSERTED INTO ANY 13-
AMPERE SOCKET.
If a new plug is to be fitted please
observe the wiring code as stated below.
If in any doubt please consult a qualified
electrician.
IMPORTANT
The wires in this mains lead are coloured
in accordance with the following code:
Blue: Neutral, Brown: Live.
As these colours may not correspond with
the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured Blue must be
connected to the terminal which is marked
with the letter N or coloured Black or Blue.
The wire which is coloured Brown must be
connected to the terminal which is marked
with the letter L or coloured Brown or Red.
WARNING: DO NOT CONNECT EITHER
WIRE TO THE EARTH TERMINAL
WHICH IS MARKED WITH THE LETTER
E, BY THE EARTH SYMBOL OR
COLOURED GREEN OR
GREEN/YELLOW.
THIS PLUG IS NOT WATERPROOF-
KEEP DRY.
Before use
Remove the connector cover.
How to replace the fuse
The location of the fuse differ according to
the type of AC mains plug (figures A and
B). Confirm the AC mains plug fitted and
follow the instructions below.
Illustrations may differ from actual AC
mains plug.
1. Open the fuse cover with a screwdriver.
2. Replace the fuse and close or attach
the fuse cover.
Fuse cover
Figure A Figure B
Figure A Figure B
Fuse
(5 ampere)
Fuse
(5 ampere)
DMC-FT4&TS4EB-VQT4E00_mst.book 3 ページ ２０１２年１月２３日 月曜日 午前９時５２分

VQT4E00 (ENG)
4
∫About the battery pack
•Do not heat or expose to flame.
•Do not leave the battery(ies) in a car exposed to direct sunlight for a long period of time with
doors and windows closed.
∫About the battery charger
•The battery charger is in the standby condition when the AC power supply cord is connected.
The primary circuit is always “live” as long as the power cord is connected to an electrical
outlet.
CAUTION
•Danger of explosion if battery is incorrectly replaced. Replace only with the type
recommended by the manufacturer.
•When disposing the batteries, please contact your local authorities or dealer and ask for
the correct method of disposal.
Warning
Risk of fire, explosion and burns. Do not disassemble, heat above 60 xC or
incinerate.
CAUTION!
To reduce the risk of fire, electric shock or product damage,
•Do not install or place this unit in a bookcase, built-in cabinet or in another
confined space. Ensure this unit is well ventilated.
DMC-FT4&TS4EB-VQT4E00_mst.book 4 ページ ２０１２年１月２３日 月曜日 午前９時５２分

5
(ENG) VQT4E00
∫Cautions for Use
•Do not use any other AV cables except the supplied one.
•Do not use any other USB connection cables except the supplied one.
•Always use a genuine Panasonic HDMI micro cable (RP-CHEU15: optional).
Part number: RP-CHEU15 (1.5 m) (5 feet)
Keep this unit as far away as possible from electromagnetic equipment (such as
microwave ovens, TVs, video games etc.).
•If you use this unit on top of or near a TV, the pictures and/or sound on this unit may be
disrupted by electromagnetic wave radiation.
•Do not use this unit near cell phones because doing so may result in noise adversely
affecting the pictures and/or sound.
•Recorded data may be damaged, or pictures may be distorted, by strong magnetic fields
created by speakers or large motors.
•Electromagnetic wave radiation generated by microprocessors may adversely affect this unit,
disturbing the pictures and/or sound.
•If this unit is adversely affected by electromagnetic equipment and stops functioning properly,
turn this unit off and remove the battery or disconnect AC adaptor (DMW-AC5E: optional).
Then reinsert the battery or reconnect AC adaptor and turn this unit on.
Do not use this unit near radio transmitters or high-voltage lines.
•If you record near radio transmitters or high-voltage lines, the recorded pictures and/or sound
may be adversely affected.
DMC-FT4&TS4EB-VQT4E00_mst.book 5 ページ ２０１２年１月２３日 月曜日 午前９時５２分

VQT4E00 (ENG)
6
Information for Users on Collection and Disposal of Old Equipment
and used Batteries
These symbols on the products, packaging, and/or
accompanying documents mean that used electrical and
electronic products and batteries should not be mixed with
general household waste.
For proper treatment, recovery and recycling of old
products and used batteries, please take them to applicable
collection points, in accordance with your national
legislation and the Directives 2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you
will help to save valuable resources and prevent any
potential negative effects on human health and the
environment which could otherwise arise from inappropriate
waste handling.
For more information about collection and recycling of old
products and batteries, please contact your local
municipality, your waste disposal service or the point of sale
where you purchased the items.
Penalties may be applicable for incorrect disposal of this
waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment,
please contact your dealer or supplier for further
information.
[Information on Disposal in other Countries outside the
European Union]
These symbols are only valid in the European Union. If you
wish to discard these items, please contact your local
authorities or dealer and ask for the correct method of
disposal.
Note for the battery symbol (bottom two symbol
examples):
This symbol might be used in combination with a chemical
symbol. In this case it complies with the requirement set by
the Directive for the chemical involved.
Cd
DMC-FT4&TS4EB-VQT4E00_mst.book 6 ページ ２０１２年１月２３日 月曜日 午前９時５２分

7
(ENG) VQT4E00
Contents
Information for Your Safety......................................................................................... 2
Before Use .................................................................................................................... 8
Accessories .................................................................................................................. 9
(Important) About the Waterproof/Dustproof and Anti-shock Performance
of the Camera ............................................................................................................. 11
Names and Functions of Main Parts ........................................................................ 17
Charging the Battery.................................................................................................. 18
Inserting and Removing the Card (optional)/the Battery ....................................... 19
Sequence of operations ............................................................................................ 20
Recording using the GPS function........................................................................... 22
Sensors (compass/altimeter/barometer) are operated........................................... 24
Restricting the GPS/sensor functions ..................................................................... 25
Reading the Operating Instructions (PDF format) .................................................. 26
Installing supplied software...................................................................................... 27
Specifications............................................................................................................. 28
DMC-FT4&TS4EB-VQT4E00_mst.book 7 ページ ２０１２年１月２３日 月曜日 午前９時５２分

VQT4E00 (ENG)
8
Before Use
•Do not apply strong shock or vibration by dropping or knocking the camera. Also, do
not apply strong pressure to the camera.
–Waterproof performance may be impaired.
–Lens or LCD monitor may be damaged.
–It may cause malfunction in the performance or the function.
∫When inner side of the lens is fogged (condensation)
It is not a malfunction or failure of the camera. It may be
caused by the environment in which the camera is used.
What to do when inner side of the lens is fogged
•Turn off the power and open the side door in a place with constant
ambient temperature, away from high temperatures, humidity,
sand and dust. The fog will disappear naturally in 10 minutes to
2 hours with the side door open when the temperature of the
camera gets close to the ambient temperature.
•Contact Panasonic’s Service Centre if the fogging does not disappear.
Conditions in which inner side of the lens may be fogged
Condensation may occur and the inner side of the lens may be fogged when the
camera is used in areas that undergo a significant change in temperature or in high
humidity, such as the following:
•When the camera is used underwater suddenly after being on a hot beach etc.
•When the camera is moved to a warm area from a cold area, such as at a ski resort or
at high altitude
•When the side door is opened in a high-humidity environment
Please be sure to read “(Important) About the Waterproof/Dustproof and Anti-shock
Performance of the Camera”(P11) before using this unit underwater to prevent the
unit from being mishandled, which may cause water to seep in.
DMC-FT4&TS4EB-VQT4E00_mst.book 8 ページ ２０１２年１月２３日 月曜日 午前９時５２分

9
(ENG) VQT4E00
Accessories
Check that all the accessories are supplied before using the camera.
Product numbers correct as of January 2012. These may be subject to change.
1 Battery Pack
(Indicated as battery pack or battery in
the text)
Charge the battery before use.
2 Battery Charger
(Indicated as battery charger or
charger in the text)
3 AC Mains Lead
4 USB Connection Cable
5AVCable
6 CD-ROM
•Software
•Operating Instructions for advanced
features
Install on your PC before use.
7Brush
8 Hand Strap
•Supplied accessories are not waterproof
(excluding Hand Strap).
•Keep the Brush out of reach of children to
prevent swallowing.
•SD Memory Card, SDHC Memory Card and
SDXC Memory Card are indicated as card in
the text.
•The card is optional.
You can record or play back pictures on the
built-in memory when you are not using a
card.
•Consult the dealer or your nearest Service
Centre if you lose the supplied accessories. (You can purchase the accessories separately.)
DMW-BCF10E DE-A60A
VFC4393
12
K1HY08YY0018
K1HY08YY0017
8
3
K2CT39A00002
6
VFF0992
7
VYC1013
5
4
DMC-FT4&TS4EB-VQT4E00_mst.book 9 ページ ２０１２年１月２３日 月曜日 午前９時５２分

VQT4E00 (ENG)
10
Sales and Support Information
Customer Communications Centre
•For customers within the UK: 0844 844 3899
•For customers within Ireland: 01 289 8333
•For further support on your product, please visit our website:
www.panasonic.co.uk
Direct Sales at Panasonic UK
•Order accessory and consumable items for your product with ease and confidence by
phoning our Customer Communications Centre Monday–Thursday 9:00 a.m.–5:30 p.m.,
Friday 9:30 a.m.–5:30 p.m. (Excluding public holidays)
•Or go on line through our Internet Accessory ordering application at www.pas-europe.com.
•Most major credit and debit cards accepted.
•All enquiries transactions and distribution facilities are provided directly by Panasonic UK.
•It couldn’t be simpler!
•Also available through our Internet is direct shopping for a wide range of finished products.
Take a browse on our website for further details.
∫Optional Accessories
¢The AC Adaptor (optional) can only be used with the designated Panasonic DC Coupler
(optional). The AC adaptor (optional) cannot be used by itself.
Some optional accessories may not be available in some countries.
Battery Pack DMW-BCF10
AC Adaptor¢DMW-AC5
DC Coupler¢DMW-DCC4
HDMI micro cable RP-CHEU15
Marine Case DMW-MCFT3
Class 10 64 GB SDXC Memory Card
Class 10 32 GB SDHC Memory Card
Class 10 16 GB SDHC Memory Card
Class 10 8 GB SDHC Memory Card
Class 10 4 GB SDHC Memory Card
Class 6 32 GB SDHC Memory Card
Class 6 16 GB SDHC Memory Card
Class 6 8 GB SDHC Memory Card
Class 6 4 GB SDHC Memory Card
Class 4 16 GB SDHC Memory Card
Class 4 8 GB SDHC Memory Card
Class 4 4 GB SDHC Memory Card
Class 4 2 GB SD Memory Card
RP-SDU64GE1K
RP-SDA32GE1K/RP-SDU32GE1K
RP-SDA16GE1K/RP-SDU16GE1K
RP-SDA08GE1K/RP-SDU08GE1K
RP-SDU04GE1K
RP-SDQ32GE1K
RP-SDQ16GE1K
RP-SDQ08GE1K
RP-SDQ04GE1K
RP-SDN16GE1A
RP-SDN08GE1A
RP-SDN04GE1A
RP-SDN02GE1A
DMC-FT4&TS4EB-VQT4E00_mst.book 10 ページ ２０１２年１月２３日 月曜日 午前９時５２分

11
(ENG) VQT4E00
(Important) About the Waterproof/
Dustproof and Anti-shock Performance of
the Camera
This does not guarantee no destruction, no malfunction, or waterproofing in all
conditions.
¢1 This means that the camera can be used underwater for specified time in specified
pressure in accordance with the handling method established by Panasonic.
¢2 “MIL-STD 810F Method 516.5-Shock” is the test method standard of the U.S. Defense
Department, which specifies performing drop tests from a height of 122 cm (4 feet), at
26 orientations (8 corners, 12 ridges, 6 faces) using 5 sets of devices, and passing the
26 orientation drops within 5 devices. (If failure occurs during the test, a new set is used to
pass the drop orientation test within a total of 5 devices)
Panasonic’s test method is based on the above “MIL-STD 810F Method 516.5-Shock”.
However, the drop height was changed from 122 cm (4 feet) to 200 cm (6.6 feet) dropping
onto 3 cm (0.1 feet) thick plyboard. This drop test was passed.
(Disregarding appearance change such as loss of paint or distortion of the part where
drop impact is applied.)
Waterproof/Dustproof Performance
This camera’s waterproof/dustproof rating complies with the “IPX8” and
“IP6X” ratings. Provided the care and maintenance guidelines described in
this document are strictly followed, this camera can operate underwater, to a
depth not exceeding 12 m (40 feet) for a time not exceeding 60 minutes. (¢1)
Anti-shock Performance
This camera also complies with “MIL-STD 810F Method 516.5-Shock”. The
camera has cleared a drop test from a height of 2 m (6.6 feet) onto 3 cm
(0.1 feet) thick plywood. In most cases this camera should not sustain any
damage if dropped from a height not exceeding 2 m (6.6 feet). (¢2)
DMC-FT4&TS4EB-VQT4E00_mst.book 11 ページ ２０１２年１月２３日 月曜日 午前９時５２分

VQT4E00 (ENG)
12
∫Handling of the camera
•Waterproofing is not guaranteed if the unit is subject to an impact as a result of being hit or
dropped etc. If an impact to the camera occurs, it should be inspected (subject to a fee) by a
Panasonic’s Service Centre to verify that the waterproofing is still effective.
•When the camera is splashed with detergent, soap, hot spring, bath additive, sun oil, sun
screen, chemical, etc., wipe it off immediately.
•Waterproof function of the camera is for sea water and fresh water only.
•Any malfunction caused by customer misuse, or mishandling will not be covered by the
warranty.
•The inside of this unit is not waterproof. Water leakage will cause malfunction.
•Supplied accessories are not waterproof (excluding Hand Strap).
•Card and battery are not waterproof. Do not handle with a wet hand. Also, do not insert wet
card or battery into the camera.
•Do not leave the camera for a long period of time in places where temperature is very low
(at ski resorts or at high altitude etc.) or very high [above 40 oC (104 oF)], inside a car under
strong sunlight, close to a heater, on the beach, etc. Waterproof performance may be
degraded.
∫About the [Precautions] demonstration display ([Requirements for
Underwater use])
•[Precautions] is displayed when the power is turned on for the first time after purchase, with
the side door completely closed.
•Please check beforehand to maintain the waterproof performance.
1Press 2to select [Yes], and press [MENU/SET].
•It will automatically skip to the clock setting screen if [No] is selected before it starts.
2Press 2/1to select the picture.
•It can be forcefully ended by pressing [MENU/SET].
•When it is forcefully ended while checking by turning the unit off or pressing [MENU/
SET], [Precautions] is displayed every time the power is turned on.
3After the final screen (12/12), press [MENU/SET] to finish.
•When [MENU/SET] is pressed after the final screen (12/12), [Precautions] is not
displayed from the next time the power is turned on.
•This can also be viewed from [Precautions] in the [Setup] menu.
2: Return to the previous screen
1: View the next screen
DMC-FT4&TS4EB-VQT4E00_mst.book 12 ページ ２０１２年１月２３日 月曜日 午前９時５２分

13
(ENG) VQT4E00
1Check that there are no foreign objects on the inner side of the side door.
ABrush (supplied)
BSide door
•If there is any foreign object, such as lint, hair, sand, etc., on the surrounding area,
water will leak within a few seconds causing malfunction.
•Wipe it off with a dry soft cloth if there is any liquid.
It may cause water leaks and malfunction if you use the camera with liquid adhered.
•If there is any foreign material, remove with supplied brush.
•Be extremely careful to remove the small sand etc. that may adhere to the sides and
corners of the rubber seal.
•Remove large foreign objects, wet sand, etc., using the shorter (harder) side of the
brush.
2Check for cracks and deformation of the rubber seal on the side door.
•The integrity of the rubber seals may decrease after about 1 year, with use and age. To
avoid permanently damaging the camera the seals should be replaced once each year.
Please contact Panasonic’s Service Centre for related costs and other information.
3Close the side door securely.
CRed part
D[LOCK] switch (grey part)
EReleased state
FLocked state
•Lock the [LOCK] switch securely until the
red part is no longer visible.
•To prevent water seeping into the camera,
be careful not to trap foreign objects such
as liquids, sand, hair or dust etc.
Check before using underwater
Do not open or close the side door in places with sand and dust, close to water,
or with wet hands. Sand or dust adhering may cause water leaks.
ロヰヤレ
ロヰヤレ
ロヰヤレ
DMC-FT4&TS4EB-VQT4E00_mst.book 13 ページ ２０１２年１月２３日 月曜日 午前９時５２分

VQT4E00 (ENG)
14
•Use the camera underwater to 12 m (40 feet) with the water temperature between 0 oC and
40 oC (32 oF and 104 oF).
•Do not use for scuba diving (Aqualung).
•Do not use the camera at a depth of over 12 m (40 feet).
•Do not use it in the hot water over 40 oC (104 oF) (in the bath or hot spring).
•Do not use the camera underwater for longer than 60 minutes continuously.
•Do not open or close the side door underwater.
•Do not apply shock to the camera underwater. (Waterproof performance may not be
maintained, and there is a chance of water leak.)
•Do not dive into the water holding the camera. Do not use the camera in a location where the
water will splash strongly, such as rapid flow or waterfall. (Strong water pressure may be
applied, and it may cause malfunction.)
•The camera will sink in the water. Take care not to drop the camera and lose it underwater by
securely placing the strap around your wrist or similar measure.
Using the camera underwater
DMC-FT4&TS4EB-VQT4E00_mst.book 14 ページ ２０１２年１月２３日 月曜日 午前９時５２分

15
(ENG) VQT4E00
1Rinse with water with the side door closed.
•After use at the seaside or underwater, soak the unit in fresh
water pooled in a shallow container for 10 minutes or less.
•If the zoom button or camera [ON/OFF] button do not move
smoothly, it may be caused by an adhesion of foreign
objects. Using in such a state may cause malfunctions, such
as locking up, so wash off any foreign objects by shaking the
camera in fresh water.
•Bubbles may come out of the drainage hole when you
immerse the camera in water, but this is not a malfunction.
Caring of the camera after using it underwater
Do not open or close the side door until the sand and dust is removed by
rinsing the camera with water.
Make sure to clean the camera after using it.
•Thoroughly wipe off any water droplets, sand, and saline matter on your hands, body, hair,
etc.
•It is recommended to clean the camera indoors, avoiding places where water spray or
sand may fall.
After using it underwater, always clean the camera rather than leaving it in a
dirty state.
•Leaving the camera with foreign objects or saline matter on it may cause damage,
discolouration, corrosion, unusual odour, or deterioration of the waterproof performance.
DMC-FT4&TS4EB-VQT4E00_mst.book 15 ページ ２０１２年１月２３日 月曜日 午前９時５２分

VQT4E00 (ENG)
16
2Drain water by holding the camera upside
down and shaking it lightly a few times.
•After using the camera at the seaside or under
water, or after washing it, water will remain at
the speaker site of the camera for a while and
it may cause lower sound or sound distortion.
•Fasten the strap firmly to prevent the camera
from dropping.
3Wipe off water drops on the camera with a
dry soft cloth and dry the camera in a
shaded area which is well ventilated.
•Dry the camera by standing it on a dry cloth.
This unit incorporates drain design, draining
water in gaps in the camera [ON/OFF] button
and zoom button etc.
•Do not dry the camera with hot air from dryer
or similar. Waterproof performance will
deteriorate due to deformation.
•Do not use chemicals such as benzine, thinner, alcohol or cleanser, soap or
detergents.
4Confirm that there are no water droplets, open the side door, and wipe off
any water droplets or sand left inside using a soft dry cloth.
•Water droplets may adhere to the card or battery when the side door is opened without
thoroughly drying. Also, water may accumulate in the gap around the card/battery slot
or the terminal connector. Be sure to wipe any water off with a soft dry cloth.
•The water droplets may seep into the camera when the side door is closed while it is
still wet, causing condensation or failure.
DMC-FT4&TS4EB-VQT4E00_mst.book 16 ページ ２０１２年１月２３日 月曜日 午前９時５２分

17
(ENG) VQT4E00
Names and Functions of Main Parts
1Flash
2 GPS status indicator
3 Motion picture button
4 Shutter button
5 Camera [ON/OFF] button
6 Self-timer indicator/
AF Assist Lamp/
LED light
7 GPS antenna
8 Microphone
9Lens
10 LCD monitor
11 Speaker
12 Zoom button
13 [(] (Playback) button
14 Strap eyelet
•Be sure to attach the strap when
using the camera to ensure that you
will not drop it.
15 Release lever
16 [LOCK] switch
17 Side door
18 [MODE] button
19 [Q.MENU]/[ ] (Delete/Cancel)
button
20 [DISP.] button
21 [MENU/SET] button
22 Cursor buttons
23 Tripod receptacle
24 [HDMI] socket
•Do not connect with any cable other
than an HDMI micro cable
(RP-CHEU15: optional). Doing so
may cause malfunction.
25 Card slot
26 [AV OUT/DIGITAL] socket
27 Battery slot
•When using an AC adaptor, ensure
that the Panasonic DC coupler
(DMW-DCC4: optional) and AC
adaptor (DMW-AC5E: optional) are
used.
•Always use a genuine Panasonic AC
adaptor (DMW-AC5E: optional).
•When using an AC adaptor, use the
AC cable supplied with the AC
adaptor.
ロヰヤレ
モヷチヰヶヵチバチュリヨ リヵモ ロ
1234567 8 9 10 11 12 13 14
17
181920
21 22
15
16
23
24
25
26
27
DMC-FT4&TS4EB-VQT4E00_mst.book 17 ページ ２０１２年１月２３日 月曜日 午前９時５２分

VQT4E00 (ENG)
18
Charging the Battery
Use the dedicated charger and battery.
•The battery is not charged when the camera is shipped. Charge the battery before use.
•Charge the battery with the charger indoors [10 oC to 30 oC (50 oF to 86 oF)].
∫About batteries that you can use with this unit
The battery that can be used with this unit is DMW-BCF10E.
Attach the battery paying attention to the
direction of the battery.
Connect the AC Mains Lead.
•The [CHARGE] indicator Alights up and charging
begins.
∫About the [CHARGE] indicator
On: Charging.
Off: Charging has completed. (Charging time: Approx. 130 min)
DMC-FT4&TS4EB-VQT4E00_mst.book 18 ページ ２０１２年１月２３日 月曜日 午前９時５２分

19
(ENG) VQT4E00
Inserting and Removing the Card
(optional)/the Battery
•Check that this unit is turned off.
•Confirm that there is no foreign object.
•We recommend using a Panasonic card.
1:Slide the [LOCK] switch A, and
release the lock.
2:Slide the release lever Band open the
side door.
•Always use genuine Panasonic batteries
(DMW-BCF10E).
•If you use other batteries, we cannot guarantee
the quality of this product.
Battery: Being careful about the battery
orientation, insert all the way until you
hear a locking sound and then check that
it is locked by lever C. Pull the lever Cin
the direction of the arrow to remove the
battery.
Card: Push it securely all the way until
you hear a “click” while being careful
about the direction in which you insert it.
To remove the card, push the card until it
clicks, then pull the card out upright.
D: Do not touch the connection terminals of the
card.
Close the side door until it clicks, and
then lock the [LOCK] switch by sliding it
toward [1].
•Confirm that the red part on the [LOCK] switch is not
showing.
Note
•Keep the Memory Card out of reach of children to prevent
swallowing.
ロヰヤレ
モヷチヰヶヵチバチュリヨリヵ モロ
ロヰヤレ
DMC-FT4&TS4EB-VQT4E00_mst.book 19 ページ ２０１２年１月２３日 月曜日 午前９時５２分

VQT4E00 (ENG)
20
Sequence of operations
Press camera [ON/OFF] button.
•The clock is not set when the camera is
shipped. Set the date and time before
using the camera.
Press the shutter button halfway to
focus and then press it fully to take
the picture.
∫Selecting the Recording Mode
Press [MODE] to select the Recording Mode.
: Take pictures with automatic settings.
: Take pictures with your own settings.
: The exposure is adjusted by the aperture value and the shutter speed which are
manually adjusted.
: This mode is optimal for taking pictures of sporting events, etc.
: This mode is optimal for taking pictures that show the snow as white as possible at
a ski resort or a snow-covered mountain.
: This mode is optimal for taking pictures underwater and at the beach.
: This is optimal for taking pictures underwater deeper than 12 m (40 feet) by the
use of the marine case (DMW-MCFT3: optional).
: Take pictures to make them look like a diorama. (also known as Tilt Shift Focus)
: Take pictures according to scene.
:Takes a 3D picture.
DMC-FT4&TS4EB-VQT4E00_mst.book 20 ページ ２０１２年１月２３日 月曜日 午前９時５２分