Panasonic Kx-tcd300e User manual

This unit is compatible with Caller ID and SMS. To use these

features, you must subscribe to the appropriate service of your

service provider.

Charge the batteries for about 7 hours before initial use.

Please read these operating instructions before using the unit and save them for

future reference.

Operating Instructions

Model No. KX-TCD300E

Digital Cordless Phone

TCD300E(e).book Page 1 Tuesday, October 12, 2004 8:22 PM

Introduction

2Helpline Tel. No.: U.K. 08700 100 076 R.O.I. 01289 8333

Introduction

Thank you for purchasing a new Panasonic digital cordless phone.

For your future reference

Attach or keep original receipt to assist with any repair under warranty.

Note:

LThis equipment is designed for use on the UK and Republic of Ireland analogue telephone

network.

LIn the event of problems, you should contact your equipment supplier in the first instance.

Declaration of Conformity:

LPanasonic Communications Co., Ltd. declares that this equipment is in compliance with the

essential requirements and other relevant provisions of Radio & Telecommunications

Terminal Equipment (R&TTE) Directive 1999/5/EC.

Declarations of Conformity for the relevant Panasonic products described in this manual

are available for download by visiting:

http://www.doc.panasonic.de

Contact:

Panasonic Services Europe GmbH

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, F.R. Germany

Trademarks:

LEatoni and LetterWise are trademarks of Eatoni Ergonomics, Inc.

Serial No. (found on the bottom of the base unit)

Date of purchase

Name and address of dealer

TCD300E(e).book Page 2 Tuesday, October 12, 2004 8:22 PM

Feature highlights

Helpline Tel. No.: U.K. 08700 100 076 R.O.I. 01289 8333

Feature highlights

Colour display

The handset’s colour display allows you to customise the handset to your

liking. You can customise the handset by selecting the “wallpaper” pattern

shown on the display in standby mode (page 23). If you set the wallpaper

to “Off”, the display colour (page 23) setting will be used instead.

Phonebook

The phonebook allows you to make calls without having to dial manually.

You can add 200 names and phone numbers to the phonebook, assign

each phonebook entry to the desired category, and search for phonebook

entries by name or category.

Phonebook category

If you subscribe to Caller ID service, phonebook categories (page 17) can

help you identify who is calling by using different display colours and

ringtones for different categories of callers (page 31).

Night mode

Night mode allows you to select a block of time during which the

handset/base unit will not ring, useful if you do not want to be disturbed, for

example, while sleeping.

Night mode can be set independently for the handset (page 22) and base

unit (page 27).

SMS (Short Message Service)

SMS allows you to send and receive text messages between other fixed-

line and mobile phones that support compatible SMS networks and

features. SMS features are available only after subscribing to Caller ID

and/or appropriate service (page 33).

Polyphonic ringtones for handset

You can change the ringtone heard when the handset rings for outside

calls and intercom calls. You can choose from 6 ringtones and 14 melody

tones (page 21).

Tom

TCD300E(e).book Page 3 Tuesday, October 12, 2004 8:22 PM

Table of Contents

4Helpline Tel. No.: U.K. 08700 100 076 R.O.I. 01289 8333

Preparation

Accessory information . . . . . . . . . . . . . . .5

Important information . . . . . . . . . . . . . . . . 7

Controls and displays. . . . . . . . . . . . . . . .8

Connections . . . . . . . . . . . . . . . . . . . . . .10

Battery installation . . . . . . . . . . . . . . . . . 11

Battery charge . . . . . . . . . . . . . . . . . . . . 11

Screen saver mode . . . . . . . . . . . . . . . .12

Battery replacement. . . . . . . . . . . . . . . .12

Turning the power on/off . . . . . . . . . . . .12

Setting the date and time . . . . . . . . . . . .13

Making/Answering Calls

Making calls . . . . . . . . . . . . . . . . . . . . . . 14

Answering calls . . . . . . . . . . . . . . . . . . .16

Phonebook

Using the phonebook . . . . . . . . . . . . . . . 17

Copying phonebook entries to other

handsets. . . . . . . . . . . . . . . . . . . . . . . . .19

Handset Settings

Guide to handset settings . . . . . . . . . . .20

Time settings . . . . . . . . . . . . . . . . . . . . .21

Ringer setup. . . . . . . . . . . . . . . . . . . . . .21

Night mode. . . . . . . . . . . . . . . . . . . . . . .22

Display setup . . . . . . . . . . . . . . . . . . . . .23

Call options . . . . . . . . . . . . . . . . . . . . . .24

Other options . . . . . . . . . . . . . . . . . . . . .24

Base Unit Settings

Guide to base unit settings. . . . . . . . . . .26

Ringer setup. . . . . . . . . . . . . . . . . . . . . .27

Call options . . . . . . . . . . . . . . . . . . . . . .28

Other options . . . . . . . . . . . . . . . . . . . . .29

Caller ID Service

Using Caller ID service. . . . . . . . . . . . . .31

Caller list . . . . . . . . . . . . . . . . . . . . . . . .32

SMS (Short Message

Service)

Using SMS (Short Message Service) . . 33

Turning SMS on/off . . . . . . . . . . . . . . . . 33

Changing SMS message centre

numbers. . . . . . . . . . . . . . . . . . . . . . . . . 33

Registering mailboxes . . . . . . . . . . . . . . 34

Sending a message . . . . . . . . . . . . . . . . 34

Receiving a message . . . . . . . . . . . . . . 36

Guide to SMS settings . . . . . . . . . . . . . . 37

Available character entries for SMS. . . . 39

Multi-unit Operation

Operating additional units . . . . . . . . . . . 41

Registering a handset to a base unit . . . 41

Intercom between handsets. . . . . . . . . . 43

Transferring calls between handsets,

conference calls. . . . . . . . . . . . . . . . . . . 43

Useful Information

Wall mounting . . . . . . . . . . . . . . . . . . . . 45

Available character entries. . . . . . . . . . . 46

Troubleshooting . . . . . . . . . . . . . . . . . . . 49

Specifications. . . . . . . . . . . . . . . . . . . . . 53

Conditions of guarantee. . . . . . . . . . . . . 54

Index

Index . . . . . . . . . . . . . . . . . . . . . . . . . . 55

TCD300E(e).book Page 4 Tuesday, October 12, 2004 8:22 PM

Preparation

Helpline Tel. No.: U.K. 08700 100 076 R.O.I. 01289 8333

Accessory information

Sales and support information

Customer Care Centre

LFor UK customers: 08700 100 076

LFor Republic of Ireland customers: 01289 8333

LVisit our website for product information: www.panasonic.co.uk

LE-mail: customer.care@panasonic.co.uk

Direct Sales at Panasonic UK

LOrder accessory and consumable items for your product with ease and confidence by

phoning our Customer Care Centre Monday - Friday, 9:00 am - 5:30 pm. (Excluding public

holidays)

LOr go on line through our Internet Accessory ordering application at

www.panasonic.co.uk

LMost major credit and debit cards accepted.

LAll enquiries transactions and distribution facilities are provided directly by Panasonic UK

Ltd.

LIt couldn’t be simpler!

LAlso available through our Internet is direct shopping for a wide range of finished products,

take a browse on our website for further details.

Additional/replacement accessories

Model No. Description

P03P 2 rechargeable nickel metal hydride (Ni-MH) batteries

KX-TCA130E Additional handset

KX-A272 DECT repeater

TCD300E(e).book Page 5 Tuesday, October 12, 2004 8:22 PM

Preparation

6Helpline Tel. No.: U.K. 08700 100 076 R.O.I. 01289 8333

Included accessories

AC adaptor

Part No. PQLV19EZ

(PQLV19E)

Telephone line cord

Part No. PQJA87S (for UK)

Rechargeable batteries

AAA (R03) size

Part No. HHR-4EPT

Handset cover

Part No.

PQYNTCD320E

Operating instructions Quick guide

SMS guide

TCD300E(e).book Page 6 Tuesday, October 12, 2004 8:22 PM

Preparation

Helpline Tel. No.: U.K. 08700 100 076 R.O.I. 01289 8333

Important information

General

LUse only the AC adaptor included with this

product, noted on page 6.

LDo not connect the AC adaptor to any AC

outlet other than a standard 220–240 V

AC outlet.

LThis product is unable to make calls when:

– The portable handset battery(ies) need

recharging or have failed.

– There is a power failure.

– The key lock feature is turned on.

– The call bar feature is turned on (only

phone numbers stored in the unit as

emergency numbers can be called).

LDo not open the base unit or handset

other than to replace the battery(ies).

LThis product should not be used near

emergency/intensive care medical

equipment and should not be used by

people with pacemakers.

LCare should be taken that objects do not

fall onto, and liquids are not spilled into,

the unit. Do not subject this product to

excessive smoke, dust, mechanical

vibration or shock.

Environment

LDo not use this product near water.

LThis product should be kept away from

heat sources such as radiators, cookers,

etc. It should also not be placed in rooms

where the temperature is less than 5 °C or

greater than 40 °C.

LThe AC adaptor is used as the main

disconnect device. Ensure that the AC

outlet is installed near the unit and is

easily accessible.

Warning:

LTo prevent the risk of electrical shock, do

not expose this product to rain or any

other type of moisture.

Location

LFor maximum distance and noise-free

operation, place your base unit:

– Away from electrical appliances such as

TVs, radios, personal computers or

other phones.

– In a convenient, high and central

location.

Battery caution

LWe recommend using the battery(ies)

noted on page 5. Use only rechargeable

battery(ies).

LDo not mix old and new batteries.

LDo not dispose of the battery(ies) in a fire,

as they may explode. Check local waste

management codes for special disposal

instructions.

LDo not open or mutilate the battery(ies).

Released electrolyte from the battery(ies)

is corrosive and may cause burns or injury

to the eyes or skin. The electrolyte may be

toxic if swallowed.

LExercise care when handling the

battery(ies). Do not allow conductive

materials such as rings, bracelets or keys

to touch the battery(ies), otherwise a short

circuit may cause the battery(ies) and/or

the conductive material to overheat and

cause burns.

LCharge the battery(ies) in accordance

with the information provided in these

operating instructions.

LOnly use the included base unit (or

charger) to charge the battery(ies). Do not

tamper with the base unit (or charger).

Failure to follow these instructions may

cause the battery(ies) to swell or explode.

TCD300E(e).book Page 7 Tuesday, October 12, 2004 8:22 PM

Preparation

8Helpline Tel. No.: U.K. 08700 100 076 R.O.I. 01289 8333

Controls and displays

Controls

Handset

ASpeaker

BCharge contact

CDisplay

DSoft keys

E{C} (Talk)

FNavigator key

L {e}{v}: To search for the desired

item in menus.

L{>}: To select the desired item or

move the cursor to the right.

L{<}: To return to the previous screen

or move the cursor to the left.

G{s} (Speakerphone)

H{R}(Recall)

IReceiver

J{ih} (Off/Power)

K{C/T}(Clear/Mute)

L{INT}(Intercom)

MMicrophone

Note:

LUp to 3 menu items can be displayed at a

time. To select a menu item not shown on

the current page, scroll up or down by

pressing the navigator key, {e} or {v},

respectively.

Base unit

A{x} (Page)

BCharge contact

Displays

Display icons

Various icons appear on the handset display

to indicate the current status of the unit.

Display

icon

Meaning

wWithin range of a base unit

LWhen flashing: Handset

is searching for base unit.

(out of range of base unit,

handset is not registered

to base unit, no power on

base unit)

TCD300E(e).book Page 8 Tuesday, October 12, 2004 8:22 PM

Preparation

Helpline Tel. No.: U.K. 08700 100 076 R.O.I. 01289 8333

Menu icons

When in standby mode, pressing the middle

soft key reveals the handset’s main menu.

From here you can access various features

and settings.

Soft keys

The handset features 3 soft keys. By

pressing a soft key, you can select the

feature or operation indicated by the soft key

icon shown directly above it.

LPressing the left, middle, or right soft key

selects the leftmost, centre, or rightmost

soft key icon respectively.

LThe icons shown will vary depending on

how you are using the unit.

Soft key icons

xHandset is accessing base

unit. (intercom, paging,

changing base unit settings,

etc.)

kHandset is on an outside

call.

xCall bar is on. (page 24)

yMissed call (Caller ID

subscribers only; page 31)

iBatteries are charging.

1Battery strength

eAlarm is on. (page 21)

dVoice enhancer is set to

high or low tone. (page 15)

URinger volume is off. (page

21)

fNight mode is on. (page 22)

[2] Handset number: The left

icon shows handset 2

example. (page 23)

-2- Base unit number: The left

icon shows base unit 2

example. (page 23)

hNew SMS message

received (SMS users only;

page 36)

jYour written SMS message

is over 160 characters.

(SMS users only; page 35)

mSMS memory is full. (SMS

users only)

Line is being used by

another handset.

Display

icon

Meaning Menu

icon

Menu/feature

WCaller List

XSMS (Short Message Service)

bTime Settings

YHandset Setup

ZBase Unit Setup

aDisplay Setup

Soft

key

icon

Action

vReturns to the previous

screen.

$Displays the main menu.

,Accepts the current selection.

qDisplays a previously dialled

phone number.

UOpens the phonebook.

TCD300E(e).book Page 9 Tuesday, October 12, 2004 8:22 PM

Preparation

10 Helpline Tel. No.: U.K. 08700 100 076 R.O.I. 01289 8333

Connections

When the AC adaptor is connected, a short

beep will be heard. If it is not heard, check

the connections.

Important:

LUse only the AC adaptor and telephone

line cord supplied with this unit.

Note:

LIf the AC outlet is connected to a switch,

make sure the switch is on.

LAfter connection, you must charge the

batteries to make or answer calls (page

11).

LNever install telephone wiring during a

lightning storm.

LThe AC adaptor must remain connected

at all times. (It is normal for the adaptor to

feel warm during use.)

LThe AC adaptor should be connected to a

vertically oriented or floor-mounted AC

outlet. Do not connect the AC adaptor to a

ceiling-mounted AC outlet, as the weight

rDisplays the phonebook

search menu.

"Turns the key lock feature off.

(page 15)

pDisplayed when adding or

editing a phonebook entry, or

when writing an SMS

message.

sInserts a dialling pause. (page

16)

wErases the selected item.

tDisplayed when the soft key

has no function.

Soft

key

icon

Action

(220–240 V, 50 Hz)

To telephone

network

Hooks

TCD300E(e).book Page 10 Tuesday, October 12, 2004 8:22 PM

Preparation

Helpline Tel. No.: U.K. 08700 100 076 R.O.I. 01289 8333

of the adaptor may cause it to become

disconnected.

LThe unit will not work during a power

failure. We therefore recommend you also

connect a standard telephone to the same

telephone line using a T-adaptor. Your

Panasonic sales shop can offer you more

information about connection possibilities.

Battery installation

1Insert the batteries negative (T)

terminal first.

2Close the handset cover.

Note:

LUse only rechargeable batteries (page 6).

Battery charge

Place the handset on the base unit for

about 7 hours before initial use.

When charging, iand battery strength

icon are alternately shown on the display.

When the batteries are fully charged, 1

flashes.

Note:

LIt takes 7 hours to fully charge the

batteries, however, you can use the

handset before the batteries are fully

charged.

LClean the charge contacts (page 8) of the

handset and base unit with a soft, dry

cloth once a month, otherwise the

batteries may not charge properly. Clean

more often if the unit is exposed to grease,

dust or high humidity.

Battery strength

Note:

LWhen 3flashes, recharge the handset

batteries. 3will continue to flash until

the batteries have been charged for at

least 15 minutes.

LIf the handset is turned off, it will be turned

on automatically when it is placed on the

base unit.

Battery icon Battery strength

1High

2Medium

3Low

When flashing: Needs

to be charged.

TCD300E(e).book Page 11 Tuesday, October 12, 2004 8:22 PM

Preparation

12 Helpline Tel. No.: U.K. 08700 100 076 R.O.I. 01289 8333

Battery life

After your Panasonic batteries are fully

charged, you can expect the following

performance:

Ni-MH batteries (700 mAh)

Note:

LActual battery performance depends on a

combination of how often the handset is in

use (talking) and how often it is not in use

(standby).

LBattery operating time may be shortened

over time depending on usage conditions

and ambient temperature.

Screen saver mode

The backlight will turn off completely after 1

minute of inactivity if the handset is not on

the base unit. Only essential icons and the

date and time will be displayed, and they will

occasionally change position in order to

preserve the life of the display.

Example:

To use the handset when it is in screen

saver mode, first press {ih} to turn the

display on again.

Battery replacement

If 3flashes even after the handset

batteries have been charged for 7 hours, the

batteries must be replaced.

Important:

LUse only the Panasonic rechargeable

batteries noted on page 5. If you install

non-rechargeable batteries and start

charging, the batteries may leak

electrolyte.

LDo not mix old and new batteries.

1Press the notch on the handset cover

firmly and slide it in the direction of the

arrow.

2Remove the old batteries positive (S)

terminal first and install the new ones.

See page 11 for battery installation.

Turning the power on/off

Power on

Press {ih} for about 1 second.

LThe display will change to the standby

mode.

Power off

Press {ih} for about 2 seconds.

LThe display will go blank.

Operation Operating time

While in use (talking) 16 hours max.

While not in use

(standby)

170 hours max.

17 May 15:30

TCD300E(e).book Page 12 Tuesday, October 12, 2004 8:22 PM

Preparation

Helpline Tel. No.: U.K. 08700 100 076 R.O.I. 01289 8333

Setting the date and time

Important:

LConfirm that the AC adaptor is connected.

LEnsure that wis not flashing. If the

handset is in screen saver mode, wis not

displayed. Press {ih} to turn the

display on.

1Press $(middle soft key).

2Select b, then press ,.

3Select “Set Date & Time”, then press

4Enter the current day, month and year by

selecting 2 digits for each.

Example: 17 May, 2004

Press {1}{7}{0}{5}{0}{4}.

5Enter the current hour and minute by

selecting 2 digits for each.

LYou can select “AM”, “PM”or 24-hour

time entry by pressing {*} repeatedly.

Example: 3:30 PM

Press {0}{3}{3}{0}, then press {*}

repeatedly until “03:30 PM”is

displayed.

6Press ,.

7Press {ih}.

Note:

LTo correct a digit, press {<} or {>} to

move the cursor, then make the

correction.

LThe date and time may be incorrect after a

power failure. In this case, set the date

and time again.

TCD300E(e).book Page 13 Tuesday, October 12, 2004 8:22 PM

Making/Answering Calls

14 Helpline Tel. No.: U.K. 08700 100 076 R.O.I. 01289 8333

Making calls

1Lift the handset and dial the phone

number.

LTo correct a digit, press {C/T}, then

enter the correct number.

2Press {C}.

3When finished talking, press {ih} or

place the handset on the base unit.

Speakerphone

The handset features a digital

speakerphone, which allows you to have

hands-free conversations.

1During a conversation, press {s} to turn

on the speakerphone.

LSpeak alternately with the caller.

2When finished talking, press {ih} or

place the handset on the base unit.

Note:

LFor best performance, please note the

following:

– Use the speakerphone in a quiet

environment.

– If you or the other party have difficulty

hearing each other, press {e} or {v}

repeatedly to adjust the speaker volume

as necessary.

LTo switch back to the receiver, press

{C}.

To adjust the receiver or speaker volume

Press {e} or {v} while talking. 4 volume

levels are available for the receiver. 6 levels

are available for the speaker.

Redial feature

Previously dialled phone numbers (each 24

digits max.) can be redialled.

To redial the last number dialled

Press q(right soft key), then press {C}

or {s}.

LIf {s} is pressed, the unit will redial

automatically if the other party’s line is

engaged.

Note:

LYou can also press {C} or {s} before

pressing q.

To make a call using the redial list

The last 10 phone numbers dialled are

stored in the redial list.

1Press q(right soft key).

LThe last number dialled will be

displayed.

2Press {e} or {v} repeatedly to select

the desired number.

LTo exit the list, press {ih}.

3Press {C} or {s}.

LIf {s} is pressed, the unit will redial

automatically if the other party’s line is

engaged.

To redial automatically

If you press {s} when redialling and the

other party’s line is engaged, the unit will

redial the phone number again

automatically. The unit will redial up to 11

times. While the handset is waiting to redial,

{s} will flash. While the handset is

redialling, mute is automatically turned on.

Note:

LAutomatic redial is cancelled when any

button (except q) is pressed.

LIf mute does not turn off after the line is

connected, press {C/T}.

To edit a number in the redial list before

calling it

1Press q(right soft key).

2Press {e} or {v} repeatedly to select

the desired number, then press $.

TCD300E(e).book Page 14 Tuesday, October 12, 2004 8:22 PM

Making/Answering Calls

Helpline Tel. No.: U.K. 08700 100 076 R.O.I. 01289 8333

3Select “Edit and Call”, then press

4Press {<} or {>} to move the cursor,

then edit the number.

LPlace the cursor on the number you

wish to erase, then press {C/T}.

LPlace the cursor to the right of where

you want to insert a number, then

press the appropriate dial key.

5Press {C}, {s}, or ,to call.

To erase numbers in the redial list

1Press q(right soft key).

2Press {e} or {v} repeatedly to select

the desired number, then press $.

3Select “Erase”, then press ,.

LIf you want to erase all numbers in the

list, select “Erase All”, then press

4Select “Yes”, then press ,.

5Press {ih}.

To store a number from the redial list into

the phonebook

1Press q(right soft key).

2Press {e} or {v} repeatedly to select

the desired number, then press $.

3Select “Add Phonebook”, then press

4Enter a name (16 characters max.; see

page 46 for character entry), then press

5Edit the phone number if necessary,

then press ,.

6Select the desired category (page 17),

then press ,2 times.

7Press {ih}.

Other features

Voice enhancer

You can change the tone quality of the

receiver while you are on a call. 3 settings

are available.

1Press $(middle soft key) during a

call.

2Select the desired setting, then press

Note:

LIf you select “High Tone”or “Low

Tone”, dis displayed.

Mute

You can mute your voice during a

conversation. While mute is turned on, you

will be able to hear the other party, but the

other party will not be able to hear you.

1To mute your voice, press {C/T}.

2To return to the conversation, press

{C/T}again.

Key lock

The handset can be locked so that no calls

or settings can be made. Incoming calls can

be answered, but all other functions are

disabled while key lock is on.

To turn key lock on, press $(middle soft

key) for about 2 seconds.

L"is displayed.

LTo turn key lock off, press "(middle

soft key) for about 2 seconds.

Note:

LCalls to emergency numbers (page 28)

cannot be made until key lock is turned

off.

LKey lock is turned off when the handset is

turned off.

Call waiting - {R}button

If a second call is received while in

conversation with the first caller, a beep tone

TCD300E(e).book Page 15 Tuesday, October 12, 2004 8:22 PM

Making/Answering Calls

16 Helpline Tel. No.: U.K. 08700 100 076 R.O.I. 01289 8333

will be heard. Press {R}button to switch

between callers.

This service requires a subscription, consult

your service provider for details.

Note:

LIf your unit is connected to a PBX (private

branch exchange), pressing {R}can allow

you to access certain features of your host

PBX such as transferring an extension

call. Consult your PBX dealer for details.

LYou can change the recall time (page 28).

Pause button (for PBX/long distance

service users)

A pause is sometimes required when

making calls using a PBX or long distance

service.

Example: If you have to dial {0}before

dialling outside numbers manually, you will

probably pause after dialling {0}until you

hear a dial tone.

1Press {0}.

2Press s(right soft key).

3Dial the phone number, then press {C}

or {s}.

Note:

LPressing s1 time creates 1 pause.

Press srepeatedly to create longer

pauses. To change pause length, see

page 28.

Answering calls

1Lift the handset and press {C} or {s}

when the unit rings.

LYou can also answer a call by pressing

any dial key from {0}to {9}, {*}, {#},

or {INT}. (Any key answer feature)

2When finished talking, press {ih} or

place the handset on the base unit.

Auto talk feature

You can answer calls simply by lifting the

handset off the base unit. You do not need to

press {C}. To turn this feature on, see

page 24.

To adjust the ringer volume when an

outside call comes in

Press {e} or {v} when an outside call

comes in.

Note:

LThe ringer volume cannot be adjusted if

the handset is on the base unit.

Other features

Handset locator

Using this feature, you can locate the

handset if it has been misplaced.

1Press {x} on the base unit.

LThe base unit will page the handset

for about 1 minute.

2To stop paging, press {x} on the base

unit or press {ih} on the handset.

TCD300E(e).book Page 16 Tuesday, October 12, 2004 8:22 PM

Phonebook

Helpline Tel. No.: U.K. 08700 100 076 R.O.I. 01289 8333

Using the phonebook

The phonebook allows you to make calls

without having to dial manually. You can add

200 names and phone numbers to the

phonebook, assign each phonebook entry

to the desired category, and search for

phonebook entries by name or category.

Adding entries to the phonebook

1Press U(left soft key), then press

2Select “New Entry”, then press ,.

3Enter the party’s name (16 characters

max.; see page 46 for character entry),

then press ,.

4Enter the party’s phone number (24

digits max.), then press ,.

5Select the desired category for the entry.

6To save the entry, press ,2 times.

7Press {ih}.

Note:

LIf there is no space to store new entries,

“Memory Full”will be displayed. Erase

unnecessary entries (page 18).

To edit/correct a mistake

Press {<} or {>} to place the cursor on the

number or character you wish to erase, then

press {C/T}. Place the cursor to the right of

where you want to insert a number or

character, then press the appropriate dial

key.

Note:

LPress and hold {C/T}to erase all

numbers or characters.

Panasonic KX-TCD300E User manual