Panasonic NN-SD686S User manual

© 2006 Panasonic Home Appliances Microwave
Oven (Shanghai) Co., Ltd. All rights reserved.
Unauthorized copying and distribution is a violation
of law.
NN-SD686S
NN-ST676M
NN-ST666W
NN-ST656W
QPQ(Australia & New Zealand)
Microwave Oven
Please file and use this manual together with the service manual for Model NN-S560WF (ORDER NO.
SIMMC0006012C3)
ORDER NO.PHAMOS0605028A3

2
NN-SD686S / NN-ST676M / NN-ST666W / NN-ST656W

3
NN-SD686S / NN-ST676M / NN-ST666W / NN-ST656W

1 SCHEMATIC DIAGRAM 5
2 CAUTIONS TO BE OBSERVED WHEN TROUBLESHOOTING
6
2.1. Check the grounding 6
2.2. Inverter warnings 6
2.3. Part replacement. 7
2.4. When the 10A fuse is blown due to the operation of the
short switch: 7
2.5. Avoid inserting nails, wire etc. through any holes in the
unit during operation. 7
2.6. Confirm after repair 7
2.7. Sharp edges 7
3 MEASUREMENTS AND ADJUSTMENTS 8
3.1. Adjustment of primary latch switch, secondary latch switch
and short switch. 8
3.2. Measurement of microwave output 8
4 EXPLODED VIEW AND PARTS LIST 9
4.1. EXPLODED VIEW 9
4.2. PARTS LIST 10
4.3. DOOR ASSEMBLY 11
4.4. WIRING MATERIALS 11
4.5. ESCUTCHEON BASE ASSEMBLY 12
4.6. PACKING AND ACCESSORIES 14
4.7. H.V. INVERTER BOARD MAIN PARTS LIST
(F606Y4V00XN) 14
5 DIGITAL PROGRAMMER CIRCUIT 15
5.1. NN-SD686S 15
5.2. NN-ST676M, ST666W, ST656W 17
5.3. PARTS LIST 19
CONTENTS
Page Page
4
NN-SD686S / NN-ST676M / NN-ST666W / NN-ST656W

1 SCHEMATIC DIAGRAM
5
NN-SD686S / NN-ST676M / NN-ST666W / NN-ST656W

Unlike many other appliances, the microwave oven is a high
voltage, high current device. It is free from danger in ordinary
use, though extreme care should be taken during repair.
Caution
Servicemen should remove their watches whenever
working close to or replacing the magnetron.
2.1. Check the grounding
Do not operate on a two wire extension cord. The microwave
oven is designed to be grounded when used. It is imperative,
therefore, to ensure the appliance is properly grounded before
beginning repair work.
2.2. Inverter warnings
DANGER, HIGH VOLTAGE AND HIGH TEMPERATURE
(HOT/LINE) OF THE INVERTER POWER SUPPLY (U)
The high voltage inverter power supply handles very high
voltage and current for the magnetron tube. Though it is
free from danger in ordinary use, extreme care should be
taken during repair.
The aluminum heat sink is also energized with high voltage
(HOT), do not touch when the AC input terminals are
energized. The power device Collector is directly connected
to the aluminum heat sink.
The aluminum heat sink may be HOT due to heat energy,
therefore, extreme care should be taken during servicing.
H.V. Inverter warning
WARNING FOR INVERTER POWER SUPPLY (U)
GROUNDING
Check the high voltage inverter power supply circuit
grounding. The high voltage inverter power supply circuit
board must have a proper chassis ground. The inverter
grounding bracket must be connected to the chassis. If the
inverter board is not grounded it will expose the user to very
high voltages and cause extreme DANGER! Be sure that
the inverter circuit is properly grounded via the inverter
earth bracket.
Grounding of the inverter circuit board
WARNING! DISCHARGE THE HIGH VOLATGE
CAPACITORS
For about 30 seconds after the oven is turned off, an
electric charge remains in the high voltage capacitors in the
inverter power supply circuit board.
When replacing or checking parts, remove the power plug
from the outlet and short the inverter output terminal of the
magnetron filament terminals to the chassis ground with an
insulated handle screwdriver to discharge. Please be sure
to touch the chassis ground side first and then short to the
output terminals.
Discharging the high voltage capacitors
WARNING
There is high voltage present with high current capabilities
in the circuits of the primary and secondary windings, choke
coil and heat sink of the inverter. It is extremely dangerous
to work on or near these circuits with the oven energized.
DO NOT measure the voltage in the high voltage circuit
including the filament voltage of the magnetron.
WARNING
Never touch any circuit wiring with your hand or with an
insulated tool during operation.
2 CAUTIONS TO BE OBSERVED WHEN
TROUBLESHOOTING
6
NN-SD686S / NN-ST676M / NN-ST666W / NN-ST656W

2.3. Part replacement.
When any part or component is to be replaced, always ensure
that the power cord is removed from the wall outlet.
2.4. When the 10A fuse is blown
due to the operation of the
short switch:
WARNING
When the 10A 250V fuse is blown due to the operation of
the interlock monitor switch, replace all of the components
(primary latch switch, door switch, short switch and power
relay B (RY1)).
1. This is mandatory. Refer to “adjustments and
measurements” for the location of these switches.
2. When replacing the fuse, confirm that it has the
appropriate rating for these models.
3. When replacing faulty switches, be sure the mounting
tabs are not bent, broken or deficient in their ability to
hold the switches.
2.5. Avoid inserting nails, wire etc.
through any holes in the unit
during operation.
Never insert a wire, nail or any other metal object through the
lamp holes on the cavity or any holes or gaps, because such
objects may work as an antenna and cause microwave
leakage.
2.6. Confirm after repair
1. After repair or replacement of parts, make sure that the
screws of the oven, etc. are neither loose nor missing.
Microwaves might leak if screws are not properly tightened.
2. Make sure that all electrical connections are tight before
inserting the plug into the wall outlet.
3. Check for microwave energy leakage. (Refer to procedure
for measuring microwave energy leakage).
CAUTION MICROWAVE RADIATION
USE CAUTION NOT TO BECOME EXPOSED TO
RADIATION FROM THE MICROWAVE MAGNETRON OR
OTHER PARTS CONDUCTING MICROWAVE ENERGY
IMPORTANT NOTICE
The following components have potentials above 2000V
while the appliance is operated.
•Magnetron
•High voltage transformer (Located on inverter (U))
•High voltage diodes (Located on inverter (U))
•High voltage capacitors (Located on inverter (U))
Pay special attention to these areas.
When the appliance is operated with the door hinges or
magnetron installed incorrectly, the microwave leakage can
exceed more than 5mW/cm2. After repair or exchange, it is
very important to check if the magnetron and the door
hinges are correctly installed.
2.7. Sharp edges
Caution
Please use caution when unpacking, installing or moving
the unit, as some exposed edges may be sharp to the touch
and cause injury if not handled with care.
7
NN-SD686S / NN-ST676M / NN-ST666W / NN-ST656W

3.1. Adjustment of primary latch
switch, secondary latch switch
and short switch.
1. Mount the Primary latch switch, the secondary latch switch
and the short switch to the door hook assembly as shown in
ILL.
NOTE:
No specific individual adjustments during
installation of the Primary latch switch, Secondary
latch switch or Short switch to the door hook are
required.
2. When mounting the door hook assembly to the oven
assembly, adjust the door hook assembly by moving it in
the direction of the arrows in the illustration, so that the
oven door will not have any play in it. Check for play in the
door by pulling the door assembly. Make sure that the latch
keys move smoothly after adjustment is completed.
Completely tighten the screws holding the door hook
assembly to the oven assembly.
3. Reconnect the short switch and check the continuity of the
monitor circuit and all latch switches again by following the
component test procedures.
3.2. Measurement of microwave
output
The output power of the magnetron can be determined by
performing IEC standard test procedures. However,due to the
complexity of IEC test procedures, it is recommended to test
the magnetron using the simple method outlined below.
Necessary Equipment:
*1 liter beaker *Glass thermometer
*Wrist watch or stopwatch
NOTE:
Check the line voltage under load.Low voltage will
lower the magnetron output. Take the temperature
readings and heating time as accurately as possible.
1. Fill the beaker with exactly one liter of tap water.Stir the
water using the thermometer and record the water’s
temperature. (recorded as T1).
2. Place the beaker on the center of glass tray.
Set the oven for High power and heat it for exactly one
minute.
3. Stir the water again and read the temperature of the water.
(recorded as T2).
4. The normal temperature rise at High power level for each
model, is as shown in table.
TABLE (1L-1min.test)
RATED OUTPUT TEMPERATURE RISE
1100W Min. 9.4°C
3 MEASUREMENTS AND ADJUSTMENTS
8
NN-SD686S / NN-ST676M / NN-ST666W / NN-ST656W

4 EXPLODED VIEW AND PARTS LIST
4.1. EXPLODED VIEW
9
NN-SD686S / NN-ST676M / NN-ST666W / NN-ST656W

4.2. PARTS LIST
NOTE:
1. When ordering replacement part(s), please use part number(s) shown in this part list.
Do not use description of the part.
2. Important safety notice:
Components identified by mark have special characteristics important for safety.
When replacing any of these components, use only manufacture’s specified parts.
NOTE:
“A” parts are supplied by CSD (Japan)
“F” parts are supplied by PHAMOS (China)
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
1F00066V00HP CAUTION LABEL 1
3F21555500AP OVEN STICKY PAPER 1
4F10014T00APG BASE 1
5F10084T00AP RUBBER FOOT 4
6F110D5Y00SAP CABINET BODY(U) 1SD686S
6F110D5Y60SAP CABINET BODY(U) 1ST676M
6F110D5Y30HAP CABINET BODY(U) 1ST666W,ST656W
7F200A8F00AP OVEN(U) 1SD686S,ST676M,ST666W
7F200A8F40AP OVEN(U) 1ST656W
8F20555L00AP COVER 1
9F21315Y00AP PULLY SHAFT 1
10 F2177-F80 WASHER 1
11 F290D9330AP ROLLER RING(U) 1
12 F30206G30AP DOOR HOOK 1
14 F31366G30AP HOOK LEVER A 1
15 F31376G30AP HOOK LEVER B 1
16 F31386G30AP HOOK LEVER C 1
17 F400A6V00QP FAN MOTOR 1AC240V,SINGLE PHASE,50Hz
18 F40084T00AP FAN BLADE 1
19 F40257D00APG AIR GUIDE A 1
20 F41444T00AP ORIFICE 1
21 A707S4T00AP STEAM SENSOR 1SD686S,ST676M,ST666W
22 F64508660AP SENSOR COVER B 1SD686S,ST676M,ST666W
24 F65434T00AP SENSOR COVER C 1SD686S,ST676M,ST666W
25 F612E8F60QP INCANDESCENT LAMP (U) 1
26 J61415G10XN MICRO SWITCH 1(PRIMARY LATCH SWITCH) (V-15G-3C25)
27 J61414T00AP MICRO SWITCH 1(SECONDARY LATCH SWITCH) (D3V-16G-3C25)
28 F61455L00CP THERMAL CUTOUT 1105°C
29 F66264T00CP THERMAL CUTOUT INSULATION BRACKET 1
30 F61785U30XN MICRO SWITCH 1(SHORT SWITCH) (D3V-1G-2C25)
31 F606Y4V00XN H.V.INVERTER (U) 1
32 2M261-M32J3Y MAGNETRON 1
33 F62306V60BP FUSE 110A/240V,50Hz
34 F40264T60APG AIR GUIDE B 1
35 F61844T00AP GROUNDING PLATE 1
36 F63265U30XN TURNTABLE MOTOR 1
37 F900C9660QP AC CORD W/PLUG 1
38 F692Y8A00QP NOISE FILTER (U) 1
39 XTWFA4+12T SCREW 4FOR MAGNETRON
40 XTTFA4+6BN SCREW 1FOR COVER
42 XTCAFA4+12AFM SCREW 1FOR CABINET BODY SIDE (SD686S)
42 XTCAFA4+12AFS SCREW 1FOR CABINET BODY SIDE (ST676M)
42 XTCAFA4+12AFW SCREW 1FOR CABINET BODY SIDE (ST666W,ST656W)
43 XTWFA4+12D SCREW 4FOR CABINET BODY
45 F02445Y00AP CAUTION LABEL 1SD686S
46 F03348F60QP MENU LABEL 1SD686S
10
NN-SD686S / NN-ST676M / NN-ST666W / NN-ST656W

4.3. DOOR ASSEMBLY
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
D1 F3018-1200 DOOR KEY A 1
D2 F301A8F70SQP DOOR A 1ST676M
D2 F301A8F70HQP DOOR A 1ST666W,ST656W
D3 F302K5L00AP DOOR E (U) 1
D4 F30215G10XN DOOR KEY SPRING 1
D5 F30854T00AP DOOR C 1
D6 F31456V60XP DOOR SCREEN A 1
D7 F31468F70BQP DOOR SCREEN B 1ST676M,ST666W,ST656W
D8 F01726V00JP CAUTION LABEL B 1
D9 F301A8F60SQP DOOR A (U) 1SD686S
4.4. WIRING MATERIALS
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
W1 F030A8A00QP LEAD WIRE HARNESS 1
W2 F030E8A00QP H.V.LEAD WIRE 1
11
NN-SD686S / NN-ST676M / NN-ST666W / NN-ST656W

4.5. ESCUTCHEON BASE ASSEMBLY
4.5.1. NN-SD686S
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
E1 F603L8F60QP D.P.CIRCUIT (AU) 1SD686S
E2 F603Y8F60QP D.P.CIRCUIT (DU) 1SD686S
E3 F800L8F60SQP ESCUTCHEON BASE (U) 1SD686S
E4 F66167D00AP FLAT CABLE 1SD686S
E6 F80725Y00SAP DOOR OPENING BUTTON 1SD686S
E7 F82565Y00AP DOOR OPENING LEVER 1SD686S
E8 F80375K00AP COOK BUTTON SPRING 1
E9 F630Y8F60SQP MEMBRANE SWITCH (U) 1SD686S
E10 F90095X00AP GROUNDING PANEL 1SD686S
E11 F803G7D00BAP POP-UP DIAL (U) 1SD686S
E12 F80187D00BAP BACKSTOP 1SD686S
E15 F00078F60SQP NAME PLATE 1SD686S
12
NN-SD686S / NN-ST676M / NN-ST666W / NN-ST656W

4.5.2. NN-ST676M, ST666W, ST656W
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
E21 F603L8F70QP D.P.CIRCUIT (AU) 1ST676M
E21 F603L8F80QP D.P.CIRCUIT (AU) 1ST666W
E21 F603L8F90QP D.P.CIRCUIT (AU) 1ST656W
E23 F630Y8F70BQP MEMBRANE SWITCH (U) 1ST676M
E23 F630Y8F80BQP MEMBRANE SWITCH (U) 1ST666W
E23 F630Y8F90BQP MEMBRANE SWITCH (U) 1ST656W
E24 F80348F70SQP ESCUTCHEON BASE 1ST676M
E24 F80348F70HQP ESCUTCHEON BASE 1ST666W,ST656W
E25 F80728F70SQP DOOR OPENING BUTTON 1ST676M
E25 F80728F70HQP DOOR OPENING BUTTON 1ST666W,ST656W
E26 F80375K00AP COOK BUTTON SPRING 1
E27 F82566K10AP DOOR OPENING LEVEL 1ST676M,ST666W,ST656W
E28 F00078F70SQP NAME PLATE 1ST676M
E28 F00078F80HQP NAME PLATE 1ST666W
E28 F00078F90HQP NAME PLATE 1ST656W
13
NN-SD686S / NN-ST676M / NN-ST666W / NN-ST656W

4.6. PACKING AND ACCESSORIES
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
P1 F00038F60QP INSTRUCTION MANUAL 1SD686S
P1 F00038F70QP INSTRUCTION MANUAL 1ST676M,ST666W,ST656W
P2 F01028F60SQP PACKING CASE,PAPER 1SD686S
P2 F01028F70SQP PACKING CASE,PAPER 1ST676M
P2 F01028F80HQP PACKING CASE,PAPER 1ST666W
P2 F01028F90HQP PACKING CASE,PAPER 1ST656W
P3 F01046K50AP UPPER FILLER 1
P4 F01055L00AP LOWER FILLER 1
P5 F01067F00AP P.E.BAG 1SD686S
P5 F01068100XN P.E.BAG 1ST676M,ST666W,ST656W
P6 F01078100XN DOOR SHEET 1
P7 F00166V20QP NOTICE 1SD686S
P8 F06014T00AP COOKING TRAY 1
P9 F01924T00AP SHEET 1ST676M
P10 F00065G40AP CAUTION LABEL 1
4.7. H.V. INVERTER BOARD MAIN PARTS LIST (F606Y4V00XN)
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
Q701
A691E4V10GP
TRANSISTOR SI 1
Q702 TRANSISTOR SI 1
DB701 AESTRS2006M DIODE SI 120A,600V
D701,D702 A62024V00GP DIODE SI 20.3A
C704,C705 ECWH30822JUA CAPACITOR 28200PF 3000VDC
T701 F609A4V00XN H.V. TRANSFORMER 1
F607D4V00XN D.P.CIRCUIT (KU) 1
L701 F50204V00XN CHOKE COIL 1
CT701 F66904V00XN CURRENT TRANSFORMER 1
14
NN-SD686S / NN-ST676M / NN-ST666W / NN-ST656W

5 DIGITAL PROGRAMMER CIRCUIT
5.1. NN-SD686S
15
NN-SD686S / NN-ST676M / NN-ST666W / NN-ST656W

16
NN-SD686S / NN-ST676M / NN-ST666W / NN-ST656W

5.2. NN-ST676M, ST666W, ST656W
17
NN-SD686S / NN-ST676M / NN-ST666W / NN-ST656W

18
NN-SD686S / NN-ST676M / NN-ST666W / NN-ST656W

5.3. PARTS LIST
5.3.1. NN-SD686S
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
BZ210 L0DDEA000014 BUZZER 12.0KHz
C352 F1H1H1010005 CHIP CAPACITOR 1100PF/50V
C40-C48,C330,C331 F1H1H102A219 CHIP CAPACITOR 11 1000PF/50V
C80,C81,C222,C228,C484,C486 F1H1H103A220 CHIP CAPACITOR 60.01µF/50V
C481 F1H1H473A220 CHIP CAPACITOR 10.047µF/50V
C15,C223,C350 F1H1E104A030 CHIP CAPACITOR 30.1µF/25V
C220,C221 F1H1A105A019 CHIP CAPACITOR 21µF/50V
C10 AECETK1V561B AL CHEM CAPACITOR 1560µF/35V
C16 AECETS1C220B AL CHEM CAPACITOR 122µF/16V
C482 AECETS1H010B AL CHEM CAPACITOR 11µF/50V
C483 AECETS1HR47B AL CHEM CAPACITOR 10.47µF/50V
C485 AECETS1H2R2B AL CHEM CAPACITOR 12.2µF/50V
CN1 K1KA03AA0115 CONNECTOR 1
CN2 K1KA03A00300 CONNECTOR 13Pin
CN3 F03526P40AG INV. HARNESS (U) 1
CN4 K1KA04AA0086 CONNECTOR 14Pin
CN6 K1MN17A00001 CONNECTOR 117Pin
CN7 K1MN17B00053 CONNECTOR 117Pin
CN8 K1MN09BA0072 CONNECTOR 1
CN9 F03547B40AP CONNECTOR 13Pin
CX320 EFOEC8004A4 CERAMIC RESONATOR 18MHz
IC1 MN101C54CGZ L.S.I. 1
IC480 C0ABBA000230 IC 1
DISP110 L5AAAFD00019 LCD 1
DISPL1 F66175E40XN LCD HOLDER 1
F67525E40XN DIFFUSION SHEET 1
Q181,Q220,Q225 2SD0601A0L CHIP TRANSISTOR 3
Q221 2SB709A0L CHIP TRANSISTOR 1
Q222 UNR211100L CHIP DIGI-TRANSISTOR 1
Q182,Q210,Q223 B1GBCFEL0002 CHIP DIGI-TRANSISTOR 3
Q10,Q180 B1BAAJ000003 TRANSISTOR 2
D180-D189 B3ACB0000065 CHIP-LED 10
D40,D220-D223,D227 B0AACK000004 DIODE 6
D10,D11,D12,D13 B0EAKT000025 DIODE 4
D25 D4EAY511A036 VARISTOR 1510V
D26,D27 D4EAY112A036 VARISTOR 2
R182,R183 D0GB101JA069 CHIP RESISTOR 2100Ω,1/10W,5%
R82,R83,R442 D0GB102JA071 CHIP RESISTOR 31KΩ,1/10W,5%
R80,R81,R223,R225,R490,R492 D0GB103JA072 CHIP RESISTOR 610KΩ,1/10W,5%
R13,R221,R228,R230,R352.R353 D0GB104JA068 CHIP RESISTOR 6100KΩ,1/10W,5%
R483,R484,R489 D0GB105JA071 CHIP RESISTOR 31MΩ,1/10W,5%
R485 D0GB154JA068 CHIP RESISTOR 1150KΩ,1/10W,5%
R488,R491 D0GB202JA071 CHIP RESISTOR 22KΩ,1/10W,5%
R181,R320 D0GB220JA072 CHIP RESISTOR 222Ω,1/10W,5%
R220,R224,R226,R229 D0GB222JA072 CHIP RESISTOR 42.2KΩ,1/10W,5%
R210 D0GB332JA072 CHIP RESISTOR 13.3KΩ,1/10W,5%
R330,R441,C441 D0GB333JA070 CHIP RESISTOR 333KΩ,1/10W,5%
R222 D0GB363JA072 CHIP RESISTOR 136K,1/10W,5%
R487 D0GB433JA072 CHIP RESISTOR 143KΩ,1/10W,5%
R227,R331,R493 D0GB471JA069 CHIP RESISTOR 3470Ω,1/10W,5%
R360,R480,R481 D0GB472JA072 CHIP RESISTOR 34.7KΩ,1/10W,5%
R486 D0GB684JA068 CHIP RESISTOR 1680KΩ,1/10W,5%
R11,R16,R211 D0AE102JA155 CARBON FILM RESISTOR 31KΩ,1/4W,5%
R12,R180 D0AE103JA155 CARBON FILM RESISTOR 210KΩ,1/4W,5%
R290 D0AE104JA155 CARBON FILM RESISTOR 1100KΩ,1/4W,5%
ZD10 B0BA5R600016 ZENER DIODE 1
RY1 AEBGJQC25F18 POWER RELAY 1
RY2 K6B1AZA00011 POWER RELAY 1
T10 G4C3AAH00008 LOW VOLTAGE TRANSFORMER 1
RE80 EVEJ1HF2224B REVOLVING ENCODER 1
19
NN-SD686S / NN-ST676M / NN-ST666W / NN-ST656W

5.3.2. NN-ST676M, ST666W, ST656W
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
BZ310 L0DDEA000014 BUZZER 12.0KHz
C221 F1H1H103A220 CHIP CAPACITOR 10.01µF/50V
C484 F1H1H103A220 CHIP CAPACITOR 10.01µF/50V (ST676M,ST666W)
C343 F1H1H1010005 CHIP CAPACITOR 1100PF/50V
C12,C340 F1H1E104A030 CHIP CAPACITOR 20.1µF/25V
C481 F1H1H473A220 CHIP CAPACITOR 10.047µF/50V (ST676M,ST666W)
C330 F1H1H102A219 CHIP CAPACITOR 11000PF/50V
C10 AECETK1V561B AL CHEM CAPACITOR 1560µF/35V
C482 AECETS1H010B AL CHEM CAPACITOR 11µF/50V (ST676M,ST666W)
C483 AECETS1HR47B AL CHEM CAPACITOR 10.47µF/50V (ST676M,ST666W)
C485 AECETS1H2R2B AL CHEM CAPACITOR 12.2µF/50V (ST676M,ST666W)
CN1 K1KA03AA0115 CONNECTOR 1
CN2 K1KA03A00300 CONNECTOR 13 Pin (ST676M,ST666W)
CN3 F03524U00AP INV.HARNESS (U) 13Pin
CN4 F03535G40XN HARNESS (U) 1
CN6 K1MN09AA0040 CONNECTOR 19Pin
CX320 EFOEC8004A4 CERAMIC RESONATOR 18.0MHz
DISP110 L5AAAEC00060 LCD 1
DISP1 HOLDER F66174U20AP LCD HOLDER 1
D10-D13 B0EAKT000025 DIODE 4
D40,D220,D221,D223 B0AACK000004 DIODE 4
D25 D4EAY511A036 VARISTOR 1510V
D26,D27 D4EAY112A036 VARISTOR 21100V
D180-D183 B3ACB0000065 CHIP-LED 4
IC1 MN101C589EX L.S.I. 1
IC480 C0ABBA000230 IC 1(ST676M,ST666W)
Q181,Q220,Q225 2SD0601A0L CHIP TRANSISTOR 3
Q226 UNR211100L CHIP DIGI-TRANSISTOR 1
Q182,Q223,Q224 B1GBCFEL0002 CHIP DIGI-TRANSISTOR 3
Q10,Q180 B1BAAJ000003 TRANSISTOR 2
R226 D0GB103JA072 CHIP RESISTOR 110K,1/10W,5%
R490,R492 D0GB103JA072 CHIP RESISTOR 210K,1/10W,5% (ST676M,ST666W)
R221,R228,R342,R343,C40-C48 D0GB104JA068 CHIP RESISTOR 13 100K,1/10W,5%
R483,R484,R489 D0GB105JA071 CHIP RESISTOR 31MΩ,1/10W,5% (ST676M,ST666W)
R485 D0GB154JA068 CHIP RESISTOR 1150KΩ,1/10W,5% (ST676M,ST666W)
R488,R491 D0GB202JA071 CHIP RESISTOR 22KΩ,1/10W,5% (ST676M,ST666W)
R320 D0GB220JA072 CHIP RESISTOR 122Ω,1/10W,5%
R220,R222,R223 D0GB222JA072 CHIP RESISTOR 32.2K,1/10W,5%
R310 D0GB332JA072 CHIP RESISTOR 13.3K,1/10W,5%
R330 D0GB333JA070 CHIP RESISTOR 133K,1/10W,5%
R181 D0GB360JA072 CHIP RESISTOR 136Ω,1/10W,5%
R331,R441 D0GB471JA069 CHIP RESISTOR 2470Ω,1/10W,5%
R360 D0GB472JA072 CHIP RESISTOR 14.7K,1/10W,5%
R480,R481 D0GB472JA072 CHIP RESISTOR 24.7K,1/10W,5% (ST676M,ST666W)
R487 D0GB433JA072 CHIP RESISTOR 143KΩ,1/10W,5%
R440,C440 D0GB512JA072 CHIP RESISTOR 25.1KΩ,1/10W,5%
R486 D0GB684JA068 CHIP RESISTOR 1680KΩ,1/10W,5% (ST676M,ST666W)
R10,R11,R311 D0AE102JA155 CARBON RESISTOR 31K,1/4W,5%
R12,R180 D0AE103JA155 CARBON RESISTOR 210K,1/4W,5%
R290 D0AE104JA155 CARBON RESISTOR 1100K,1/4W,5%
RY1 AEBGJQC25F18 POWER RELAY 118V
RY2 K6B1AZA00011 POWER RELAY 118V
T10 G4C3AAH00008 LOW VOLTAGE TRANSFORMER 1
ZD10 B0BA5R600016 ZENER DIODE 1
20
NN-SD686S / NN-ST676M / NN-ST666W / NN-ST656W
05/06
S-8F6
S-8F7
S-8F8
S-8F9
Printed in China