Panda-Audio Future Impact I User manual
EU Directives on the Protection of the Environment
RoHS
This product is compliant with the EU Directive 2002/95/EG for the Restriction of the use of
Certain azardous Substances in Electrical and Electronic Equipment. No lead (Pb) cadmium (Cd),
mercury ( g), hexavalent chromium (Cr + 6), PBB or PBDE is intent
ionally added to this device. Any
traces of impurities of these substances contained in the parts are below the Ro S specified threshold
levels.
REACh
This product is compliant with the European Union Directive EC1907/206 and contains none or
less than 0.
1% of the chemicals listed as hazardous chemicals in the REACh regulation.
WEEE
As with the disposal of all old electrical and electronic equipment, this product is not to be
treated as regular household waste. Instead it shall be handed over to the appli
cable collection point
for recycling of electrical and electronic equipment.
This product complies with the European Union Council Directives and Standards relating to
electromagnetic compatibility EMC Directive (2006/95/EC) and the Low Voltage
(2004/108/EC). EMC compliance test report: EMC – 130930/1
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and;
(2)
This device must accept any interference received, including interference that m
cause undesired operation.
Warranty
If your Future Impact I system defects or malfunctions
as a result of any defected electronic parts or
our design fault we provide you two years warranty of repairing or replacing it.
WARNING: NEVER
press the Bank button by foot. It must be controlled by hand only. Damage of the
Bank switch will not be covered by warranty.
Panda-Audio Ltd.
Széchenyi u. 8
2040 Budaörs, HU GARY
www.panda-audio.com
Tel.: +36-23-441-071
Email: [email protected]
-
4
-
This product is compliant with the EU Directive 2002/95/EG for the Restriction of the use of
Certain azardous Substances in Electrical and Electronic Equipment. No lead (Pb) cadmium (Cd),
ionally added to this device. Any
traces of impurities of these substances contained in the parts are below the Ro S specified threshold
This product is compliant with the European Union Directive EC1907/206 and contains none or
1% of the chemicals listed as hazardous chemicals in the REACh regulation.
As with the disposal of all old electrical and electronic equipment, this product is not to be
cable collection point
This product complies with the European Union Council Directives and Standards relating to
electromagnetic compatibility EMC Directive (2006/95/EC) and the Low Voltage
Directive
This device must accept any interference received, including interference that m
ay
as a result of any defected electronic parts or
press the Bank button by foot. It must be controlled by hand only. Damage of the
Bass Guitar Synthesizer and
Analog Modeling
Synthesizer Expander
Quick Start Guide Version 1.
Panda
Hungary
www.panda
Bass Guitar Synthesizer and
Analog Modeling
MIDI
Synthesizer Expander
Quick Start Guide Version 1.
22
Panda
-Audio Ltd
Hungary
www.panda
-audio.com
Introduction
The Future Impact Bass Guitar Synthesizer and Analog MIDI Synthesizer Expander will let you
play amazing synth bass lines from your bass guitar. You can choose from 99 bass synth
sounds that you can quickly shape to your taste. With the true bypass you have the unaltered
sound when the effect is turned off.
Setting up FI
Connect your bass guitar to the I PUT jack. Connect the OUTPUT to an amplifier. Use a
Roland/Boss compatible 9V, minimum 100mA stabilised power supply with the minus pole in
the middle. You have to use a power supply according to the mains voltage and connector
requirements in your country. The power supply is not part of the delivery.
Press the O /OFF footswitch (right) to turn the effect on. The O LED will light up. Adjust
I PUT LEVEL so that the red LED lights up briefly only at the loudest pickings. Adjust OUTPUT
LEVEL to your needs. ote: due to the true bypass of the FI the level display will work only
when the effect is O .
Operating FI
The FI has 99 sounds distributed into 10 banks (bank 0 has 9 sounds, all others 10). You can
step up through the banks by pressing the EDIT/BA K UP dial that is a pushbutton switch as
well. Also, if you press down EDIT/BA K UP and turn the dial, you can quickly reach any bank.
You can select from the sounds within a bank with the PROGRAM footswitch. It will increment
the program number, but the LEDs start to blink and the sound does not change yet. Press the
O /OFF footswitch to enable the selected sound. If you quickly double-step on PROGRAM
you can also decrement the program number.
ote: The FI is based on the detection of the bass guitar’s pitch. It requires monophonic notes
that are played clean. If you play chords, power chords, slapping, tapping, or if you try to use
it outside of the pitch range of a bass guitar then unpredictable results will happen.
Editing the Sounds
If you selected a sound that you like but you want to modify it for your music, you can edit
the most important parameters. The PARAMETER SELECTOR lets you select between 13
parameters that you can change. Two of them are GLOBAL, thus common for all programs,
the other 11 are specific for each program individually. All parameters have a default value of
5. You can deviate from the default 4 steps down to 1, or 4 steps up to 9. You should use the
EDIT dial to change the parameters. When you change a parameter the change in the sound
immediately happens, and the decimal point starts to blink. Changes will be stored only if you
press the EDIT button. This will also store the program number as a default, so when you turn
on the FI next time this will be the program that appears.
Description of the Parameters
NO E OFF LEVEL (global): A lower value allows you to sustain notes longer. With a
higher value you can articulate staccato notes better.
NO E ON LEVEL (global): Sensitivity for triggering a sound. If weak pickings are not
recognized then decrease the value. If multiple notes are triggered then increase it.
A ACK: The fade-in time of the sound can be changed.
DECAY: The decay time of the filter during a sustained note can be shaped.
ENVELOPE DEP H: The contour of the sound can be made brighter or smoother.
DYNAMICS: Changes the response to dynamic playing.
CU OFF: The brightness of the filtered sound can be changed.
RESONANCE: The character of the sound can be made sharper or smoother.
BALANCE: Changes the balance between the bass and the synth sound.
LEVEL: Changes the output level of the sound.
EFFEC S: Changes the amount of effect added to the sound.
Configuring Future Impact
Press the left footswitch while you power on. Turn the Parameter dial to the leftmost
position, ote Off Level to see the name of a parameter, and turn it to right to any
other position to see the value of the parameter. The value can be changed with the
edit dial. Step through the parameters with pressing the left footswitch again. When
ready with editing turn FI off and on again. Only the two most important parameters of
this list are explained here, others are in the detailed User Guide.
RESE ALL: ame: “rS”, meaning RESET. Value: 0. If it is changed to 1 all sound para-
meters will be reset to default (5). The default sound at power on will be reset to (1).
DEFAUL Mode or DIREC Mode: ame: “PrG”, meaning PROGRAM. Value: Either “0”
(DEFAULT) or “1” (DIRECT). DEFAULT Mode is as described in “Operating FI”. In DIRECT
Mode you get a program change immediately when you hit the PROGRAM button.
Single step will increase program, double-step will decrease it. If you keep PROGRAM
pressed, the number starts to scroll up, first slowly, then faster. If you keep it down
after a double-step, it will scroll down. In DIRECT Mode increment-decrement will step
over bank borders, you can access any of the 99 programs.
User Guide
Find the full User Guide at www.pandamidi.com/support/
The product web site is at http://pandamidi.com/bass-guitar-synth/
-
3
-
-
2
-
Introduction
The Future Impact Bass Guitar Synthesizer and Analog MIDI Synthesizer Expander will let you
play amazing synth bass lines from your bass guitar. You can choose from 99 bass synth
sounds that you can quickly shape to your taste. With the true bypass you have the unaltered
sound when the effect is turned off.
Setting up FI
Connect your bass guitar to the I PUT jack. Connect the OUTPUT to an amplifier. Use a
Roland/Boss compatible 9V, minimum 100mA stabilised power supply with the minus pole in
the middle. You have to use a power supply according to the mains voltage and connector
requirements in your country. The power supply is not part of the delivery.
Press the O /OFF footswitch (right) to turn the effect on. The O LED will light up. Adjust
I PUT LEVEL so that the red LED lights up briefly only at the loudest pickings. Adjust OUTPUT
LEVEL to your needs. ote: due to the true bypass of the FI the level display will work only
when the effect is O .
Operating FI
The FI has 99 sounds distributed into 10 banks (bank 0 has 9 sounds, all others 10). You can
step up through the banks by pressing the EDIT/BA K UP dial that is a pushbutton switch as
well. Also, if you press down EDIT/BA K UP and turn the dial, you can quickly reach any bank.
You can select from the sounds within a bank with the PROGRAM footswitch. It will increment
the program number, but the LEDs start to blink and the sound does not change yet. Press the
O /OFF footswitch to enable the selected sound. If you quickly double-step on PROGRAM
you can also decrement the program number.
ote: The FI is based on the detection of the bass guitar’s pitch. It requires monophonic notes
that are played clean. If you play chords, power chords, slapping, tapping, or if you try to use
it outside of the pitch range of a bass guitar then unpredictable results will happen.
Editing the Sounds
If you selected a sound that you like but you want to modify it for your music, you can edit
the most important parameters. The PARAMETER SELECTOR lets you select between 13
parameters that you can change. Two of them are GLOBAL, thus common for all programs,
the other 11 are specific for each program individually. All parameters have a default value of
5. You can deviate from the default 4 steps down to 1, or 4 steps up to 9. You should use the
EDIT dial to change the parameters. When you change a parameter the change in the sound
immediately happens, and the decimal point starts to blink. Changes will be stored only if you
press the EDIT button. This will also store the program number as a default, so when you turn
on the FI next time this will be the program that appears.
Description of the Parameters
NO E OFF LEVEL (global): A lower value allows you to sustain notes longer. With a
higher value you can articulate staccato notes better.
NO E ON LEVEL (global): Sensitivity for triggering a sound. If weak pickings are not
recognized then decrease the value. If multiple notes are triggered then increase it.
A ACK: The fade-in time of the sound can be changed.
DECAY: The decay time of the filter during a sustained note can be shaped.
ENVELOPE DEP H: The contour of the sound can be made brighter or smoother.
DYNAMICS: Changes the response to dynamic playing.
CU OFF: The brightness of the filtered sound can be changed.
RESONANCE: The character of the sound can be made sharper or smoother.
BALANCE: Changes the balance between the bass and the synth sound.
LEVEL: Changes the output level of the sound.
EFFEC S: Changes the amount of effect added to the sound.
Configuring Future Impact
Press the left footswitch while you power on. Turn the Parameter dial to the leftmost
position, ote Off Level to see the name of a parameter, and turn it to right to any
other position to see the value of the parameter. The value can be changed with the
edit dial. Step through the parameters with pressing the left footswitch again. When
ready with editing turn FI off and on again. Only the two most important parameters of
this list are explained here, others are in the detailed User Guide.
RESE ALL: ame: “rS”, meaning RESET. Value: 0. If it is changed to 1 all sound para-
meters will be reset to default (5). The default sound at power on will be reset to (1).
DEFAUL Mode or DIREC Mode: ame: “PrG”, meaning PROGRAM. Value: Either “0”
(DEFAULT) or “1” (DIRECT). DEFAULT Mode is as described in “Operating FI”. In DIRECT
Mode you get a program change immediately when you hit the PROGRAM button.
Single step will increase program, double-step will decrease it. If you keep PROGRAM
pressed, the number starts to scroll up, first slowly, then faster. If you keep it down
after a double-step, it will scroll down. In DIRECT Mode increment-decrement will step
over bank borders, you can access any of the 99 programs.
User Guide
Find the full User Guide at www.pandamidi.com/support/
The product web site is at http://pandamidi.com/bass-guitar-synth/
-
3
-
-
2
-
EU Directives on the Protection of the Environment
RoHS
This product is compliant with the EU Directive 2002/95/EG for the Restriction of the use of
Certain azardous Substances in Electrical and Electronic Equipment. No lead (Pb) cadmium (Cd),
mercury ( g), hexavalent chromium (Cr + 6), PBB or PBDE is intent
ionally added to this device. Any
traces of impurities of these substances contained in the parts are below the Ro S specified threshold
levels.
REACh
This product is compliant with the European Union Directive EC1907/206 and contains none or
less than 0.
1% of the chemicals listed as hazardous chemicals in the REACh regulation.
WEEE
As with the disposal of all old electrical and electronic equipment, this product is not to be
treated as regular household waste. Instead it shall be handed over to the appli
cable collection point
for recycling of electrical and electronic equipment.
This product complies with the European Union Council Directives and Standards relating to
electromagnetic compatibility EMC Directive (2006/95/EC) and the Low Voltage
(2004/108/EC). EMC compliance test report: EMC – 130930/1
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and;
(2)
This device must accept any interference received, including interference that m
cause undesired operation.
Warranty
If your Future Impact I system defects or malfunctions
as a result of any defected electronic parts or
our design fault we provide you two years warranty of repairing or replacing it.
WARNING: NEVER
press the Bank button by foot. It must be controlled by hand only. Damage of the
Bank switch will not be covered by warranty.
Panda-Audio Ltd.
Széchenyi u. 8
2040 Budaörs, HU GARY
www.panda-audio.com
Tel.: +36-23-441-071
Email: [email protected]
-
4
-
This product is compliant with the EU Directive 2002/95/EG for the Restriction of the use of
Certain azardous Substances in Electrical and Electronic Equipment. No lead (Pb) cadmium (Cd),
ionally added to this device. Any
traces of impurities of these substances contained in the parts are below the Ro S specified threshold
This product is compliant with the European Union Directive EC1907/206 and contains none or
1% of the chemicals listed as hazardous chemicals in the REACh regulation.
As with the disposal of all old electrical and electronic equipment, this product is not to be
cable collection point
This product complies with the European Union Council Directives and Standards relating to
electromagnetic compatibility EMC Directive (2006/95/EC) and the Low Voltage
Directive
This device must accept any interference received, including interference that m
ay
as a result of any defected electronic parts or
press the Bank button by foot. It must be controlled by hand only. Damage of the
Bass Guitar Synthesizer and
Analog Modeling
Synthesizer Expander
Quick Start Guide Version 1.
Panda
Hungary
www.panda
Bass Guitar Synthesizer and
Analog Modeling
MIDI
Synthesizer Expander
Quick Start Guide Version 1.
22
Panda
-Audio Ltd
Hungary
www.panda
-audio.com
Other manuals for Future Impact I
2
Table of contents
Other Panda-Audio Synthesizer manuals
