Pandora Finder User manual

Pandora would like to thank you for choosing
our autonomous GPS tracker.
FINDER
Web-site: pandorainfo.com
Customer support: [email protected]

AUTONOMOUS TRACKER PANDORA FINDER USER MANUAL
2 3
GENERAL INFORMATION
The Pandora Finder tracker is a modern highly eective device that
is used to determine the coordinates and track the movement of the
monitored object.
Miniature sizes of the tracker allow placing it almost anywhere (in a
bag, in a valuable parcel, on the collar of your pet, in a vehicle). A special
application and a website provide information about the state, location
and movement of the device and make it’s usage as easy as possible.
Built-in interfaces allow you to locate the tracker using GPS/GLONASS
or LBS service, to monitor the environment and object state using
the built-in microphone, to manage the unit using SMS commands,
to receive coordinates on detecting movement using the built-in
accelerometer, to easily congure the tracker via wireless Bluetooth-
connection.
Well-thought-out functional and modern components will help you
comfortably use our products
TABLE OF CONTENTS
General information 3
System set 4
Specification 4
Tracker modes 6
Tracker functions 7
Owner’s card 9
Getting started 10
Pandora NAV BT app 15
Firmware update 17
Control using SMS commands 17
Replacing or recharging the batteries 19
Tracker installation 19
Warranty obligations 20
Acceptance certificate 24
Warranty card 24

AUTONOMOUS TRACKER PANDORA FINDER USER MANUAL
4 5
SYSTEM SET
1. Autonomous tracker 1
2. SIM-card 1
3. Fastening kit 1
4. AAA Batteries 3
5. Owner’s card 1
6. User manual 1
7. Packaging 1
NOTE! ThE maNufacTurEr rEsErvEs ThE righT TO chaNgE ThE sET
aNd cONsTrucTiON Of ThE prOducT TO imprOvE iTs TEchNOlOgical
aNd OpEraTiONal paramETErs wiThOuT NOTificaTiON.
SPECIFICATION
PARAMETER VALUE
Tracker operation voltage 3V-5,5V
Current consumption in the
Sleep/Transmission mode <4mA / <100mA
Battery/Amount AAA / 3 pcs.
GSM-modem Telit GE866-QUAD
SIM-card type nano-SIM
2.4 GHz transmission protocol Bluetooth 4.2 Low Energy
GPS/GLONASS module Telit SE868
Accelerometer Kionix KX022-1020
Microphone STMicroelectronics MP33AB01H
Operation temperature range
(depends on the batteries) - 40 С° + 85 С°
Dimensions 54х46х17.7 mm
1 The LED indicator is an s an information red light indicator. It
displays the current state or mode of the device.
2 The VALET button is used to activate the tracker and to change
settings of the device.
3 Side fastenings are used to x the tracker using clips.
4 Magnetic fastenings are using to x the tracker on a metal surface.
VALET button
Fastening
Fastening
LED indicator
1
2
3
4

AUTONOMOUS TRACKER PANDORA FINDER USER MANUAL
6 7
TRACKER MODES
• Transportation mode. This mode will have been active since the
moment of manufacture of the device. The tracker will exit this
mode after conguring the owner’s phone number or the additional
phone number. If all phone number are deleted from the tracker
memory, the device will activate the transportation mode again.
NOTE! ThE maiN OwNEr’sphONE NumbEr caN bE dElETEd ONly by
ThE paNdOra Nav bT app.
• Autonomous beacon mode. This mode is the main and it will be
automatically activated after any phone number is added in the
device memory. The device is in sleep mode the most of the time in
this mode. The tracker «wakes up» (switch on GSM/GPS interfaces)
for a short time with a preset periodicity in order to inform the
owner about its location and state.
• Tracking mode. The owner forcibly turns on this mode to track the
device location in real time and to activate the “Listening”function.
In this mode, the tracker determines the current coordinates with
a certain periodicity and sends them to the server to form the track
of the object. This mode is congured using the internet service or/
and SMS.
WARNING! IF YOU ACTIVATE TRACKNIG MODE AT THE
MOMENT WHEN THE TRACKER IS IN SLEEP MODE. IT WILL BE
ACTIVATED WHEN THE DEVICE WAKES UP THE NEXT TIME.
TRACKER FUNCTIONS
• Movement control function. This function is activated by a user to
detect movement of the tracker.
• Listening function. This function switches on the built-in
microphone to perform audio control of the environment.
This function can be activated by an SMS command or a phone call.:
- Call the tracker from the phone number that is programmed to the
tracker memory when the device is in the “Tracking”mode. The built-in
microphone will be switched on when the tracker accepts the call;
- When the device is in the“Autonomous beacon”or“Tracking” mode,
send the following SMS command: ХХХХ*007* (see the“CONTROL BY
SMS COMMANDS” section) to the tracker from a the phone number that
is programmed to the tracker memory. When the tracker wakes up, it
will call the sender phone number and switch on the microphone.
• Tracker functions with the VALET button
Tracker activation. This function sequentially switches on the tracker
interfaces in order to change its parameters and settings.
Removing a mobile device. This function removes the previously
paired mobile device from the tracker memory (removing Bluetooth
connection).

AUTONOMOUS TRACKER PANDORA FINDER USER MANUAL
8 9
Firmware update via Bluetooth connection
Function VALET button LED indicator
Tracker activation Hold for 3 seconds 3 short ashes
Removing a
mobile device Hold for 6 seconds 6 short ashes
Firmware update Hold for 10 seconds
or more
9 short ashes +
following smooth icker
• LED indication
Bluetooth-connection is available
Uploading data to the server
GPS coordinates detection
Main owner’s phone can
be programmed
Available for an incoming call
Incoming call
Tracking mode is active
OWNER’S CARD
The owner’s plastic card contains private information under the
protective layer.
WARNING! CAREFULLY ERASE THE PROTECTIVE LAYER, DO
NOT USE SHARP OBJECTS TO AVOID DAMAGING OF THE HID-
DEN INFORMATION UNDER THE LAYER. THE HIDDEN INFOR-
MATION UNDER THE PROTECTIVE LAYER IS INTENDED ONLY
FOR THE DEVICE OWNER. THE OWNER’S PERSONAL CARD
AND THE HIDDEN INFORMATION CANNOT BE RESTORED.
• LOGIN is a 10-digit number
used to add the device to the
internet service.
• PASS (Password). This
information is used to add the
device to the internet service.
The pass contains 8 characters
and can consist of digits, lower
and upper case letters.
• System phone number –
phone number of the SIM-card
that is included in the system
set. The SIM-card can be
changed by a user or by a
dealer.
• PIN – not used
+7-9хх-ххх-хх-хх
1070000000 / Y34aC4vJ
LOGIN / PASS
PIN The phone number
of the system

AUTONOMOUS TRACKER PANDORA FINDER USER MANUAL
10 11
GETTING STARTED
WARNING! THE ONWER SHOULD MONITOR THE STATUS AND
ACCOUNT BALANCE OF THE SIM-CARD INSTALLED IN THE
DEVICE. IF THE SIM-CARD IS LOCKED OR DEFECTIFE, THE
FUNCTIONALITY OF THE TRACKER WILL BE UNAVAILABLE.
STEP 1 – Create and account and add your tracker
In order to use our online services pandora-on.com and mobile apps
Pandora Online (Android), Pandora Pro (iOS), it is required to create an
account and add your device to your account. Follow the “Registration”
procedure”on pandora-on.com or in mobile apps Pandora Online or
Pandora Pro to create an account. The data created at the registration
stage (login – your email address, password – your own password)
is used to login to the account. An email with the conrmation link
will be sent to your e-mail address after the registration procedure is
completed. The registration of the account will be completed after you
follow the provided link.
WARNING! IF YOU HAVEN’T RECEIVED THE CONFIRAMTION
E-MAIL, CHECK THE SPAM FOLDER OR FOLLOW THE “FORGOT
PASSSWORD” PROCEDURE ON THE MAIN PAGE OF PANDO-
RA-ON.COM
Web-service: pandora-on.com
The mobile apps can be downloaded from the appropriate app store:
App Store (iOS) – Pandora Pro;
Google Play (Android) - Pandora Online.
WARNING! MINIMUM REQUIREMENTS FOR MOBILE DEVICES:
ANDROID V4.4; IOS V10.
STEP 2 – Add the tracker to your account.
Login to the web-service pandora-on.com or mobile app Pandora
Online/Pandora Pro with the specied data (email address and your
own password). Proceed to the “Add a device/Add a system”window
and enter the LOGIN and PASS written on the Owner’s card and add the
device. You will get access to the tracker status and settings after adding
the device to your account
STEP 3 – Prepare the device for operation
Carefully disassemble the device and install batteries keeping in mind
the correct polarity. Assemble the tracker keeping the original layout of
the parts. The tracker is in the“Transportation”mode at the moment of
the shipment.
WARNING! WE RECOMMEND THAT YOU UPDATE FIRMWARE
OF THE TRACKER BEFORE THE NEXT STEPS.
STEP 4 – Set the owner’s phone number
Owner’ phone number is a phone number that is set by a user. The
device will exit the “Transportation”mode and enter the “Autonomous
beacon” mode after this phone number is programmed (see the
“TRACKER MODES” section).
NOTE! afTEr ThE OwNEr’sphONE is prOgrammEd aNd ThEN
Each TimE whEN ThE TrackEr wackEs up, iT will sEarch fOr gps

AUTONOMOUS TRACKER PANDORA FINDER USER MANUAL
12 13
cOOrdiNaTEs. wErEccOmNEd TO lOcaTE ThE TrackEr iN placEs ThaT
arE fiNE fOr ThE saTEliTE sigNal aT ThEsE mOmENTs. OThErwisE, iT
will bE dificulT TO dETErmiNE TrackEr lOcaTiON.
There are three ways to set the owner’s phone number:
• Log in to pandora-on.com with the previously registered account.
Go to the “SETTINGS” – “NOTIFICATIONS” menu. Enter the owner’s
phone number in the “Main number” eld in the following format:
+xxхххххххххх. Save the settings after entering the number.
• Activate the tracker by pressing and holding the VALET button for
3 seconds (3 short ashes of the LED). Release the button after the
third ash. The tracker will receive the settings from the Internet-
service within 10 minutes.
• Activate the tracker by pressing and holding the VALET button for
3 seconds (3 short ashes of the LED). Release the button after the
third ash. The tracker will enter the settings mode. After that, it
will be available for a call within two minutes. Make a call from the
owner’s number to the phone number of the device at the given
time. The system will automatically remember the number of the
incoming call as the owner’s number and will end the call.
• This setting is available after a mobile phone is paired with the
tracker (see the PANDORA NAV BT MOBILE APPLICATION section).
Make a Bluetooth connection with the tracker via the mobile
application PANDORA NAV BT. Enter your phone number in the
following format +xxхххххххххх in the“Notication number 1”
eld in the “Settings –Phone”menu. Disconnect the Bluetooth
connection after the settings are complete.
•
After you program any phone number, the tracker is ready to work
(default settings is 1 “waking up”per 12 hour).
WARNING! IF A PHONE NUMBER HAS NOT BEEN PRO-
GRAMMED OR ALL PHONE NUMBER HAS BEEN DELETED
FROM THE DEVICE MEMORY, THEN THE TRACKER WILL GO TO
“TRANSPORTAITION MODE”
STEP 5 – Additional settings
To change default settings of the tracker, use the Pandora NAV BT app
(see the “PANDORA NAV BT APPLICATION” section) or online service
pandora-on.com.
An example of changing settings using the pandora-on.com:
– go to the “SETTINGS” menu
– go to the “CONNECTION” submenu;
– Set time when the tracker will wake up by the “Frequency” and
“Activation time” settings;
– Save the changed settings.
NOTE! This sETTiNg is alsO availablE iN ThE mObilE apps.
SMS notication settings:
- go the “SETTINGS” menu;

AUTONOMOUS TRACKER PANDORA FINDER USER MANUAL
14 15
- go the “NOTIFICATIONS” submenu;
- you can add additional phone numbers for SMS notications and access
to the“Listening”function if needed;
- in the “Activation”column, set a notication sign opposite the main or
additional phone number;
- Save the changed settings.
NOTE! This sETTiNg is alsO availablE iN ThE mObilE apps
PUSH and E-mail notication settings:
- go the “ADMINISTRATIVE SETTINGS”menu;
- go the “RULES”submenu;
- use the “ADD RULE” button to create two rules;
- select the “Event group” rule, Select the “Point” event, select your device
in the right column and save the settings;
- select the “Low balance”rule, enter a minimum balance value to send
a notication, select your device in the right column and save the
settings;
- go back to the “RULES”submenu, assign email notications in the
“E-mail” column and push notications to mobile devices with the
installed app(Pandora Online/Pro) in the “PUSH” column.
NOTE! yOu caN crEaTE up TO 3 rulEs uNdEr asiNglE accOuNT.
lOgiN TO ThE mObilE app (paNdOra ONliNE/prO) TO sEE yOur
phONE iN ThE “push” cOlumN. TOblOck (dElETE) amObilE dEvicE
frOm yOur accOuNT gO TO ThE prOfilE sETTiNgs (click ON ThE usEr
NamE ON ThE maiN pagE).
When you nish conguring the tracker, activate the tracker by
holding the VALET button for 3 seconds (3 ashes of the LED), the
tracker will be activated and will conrm the new settings.
PANDORA NAV BT APP
Pandora NAV BT application is a tool for setting up and updating rmware
of the tracker. The connection between the application and the tracker is
established only with the mobile device that was previously added to the
system memory via a special coded Bluetooth Low Energy protocol (see
the “Pairing/removing a mobile device”section).
You can download free Pandora NAV BT application for your
mobile device in the application store (Google Play).
WARNING! TO USE THE MOBILE APPLICATION WITH THE
TRACKER, YOUR DEVICE SHOUD HAVE ANDROID 4.4 OR
HIGER AND BLUETOOTH 4.0 MODULE; IOS V10.”
Pairing/removing a mobile device
• To pair a mobile phone with the tracker:

AUTONOMOUS TRACKER PANDORA FINDER USER MANUAL
16 17
- Turn on the Bluetooth on your phone and run the Pandora NAV BT app;
- Press and hold the VALET button for 3 seconds (3 ashes of the LED),
release the button after the third ash – the tracker will activate the
Bluetooth connection;
- Select the found device in the «Search» menu of the application,
enter the pairing PIN-code 0-0-0-0-0-0, the devices will be paired after
conrming the PIN-code entry.
NOTE! TOrE-pair ThE mObilE dEvicE wiTh ThE TrackEr, iT is
rEquirEd TO rEmOvE ThE bluETOOTh cONNEcTiON frOm ThE mObilE
phONE aNd frOm ThE TrackEr.
• To remove a mobile device from the tracker memory:
- Press and hold the VALET button for 6 seconds (until a 6 ash of the
LED), release the button after the 6th ash – the tracker will remove the
previously paired device;
- Then the tracker will activate pairing mode for 1 minute.
Using the app
Being in the Bluetooth radio coverage zone, Press and hold the VALET
button for 3 seconds (3 ashes of the LED), run the PANDORA NAV BT
application. The application will automatically detect the system and
make a connection. The main menu will be opened after making the
connection.
FIRMWARE UPDATE
In order to update the tracker rmware, press and hold the VALET
button form more than 10 seconds until smooth icker appears.. Run
the PANDORA NAV BT, go to «Search device» and select the found
device.
You can select one of the update options
• internet - you can upload the latest rmware from the internet
server.;
• File manager (Only for Android)- you can upload the rmware from
the phone’s memory. (the rmware is available on pandorainfo.com).
CONTROL USING SMS COMMANDS
The tracker can receive and execute SMS commands. The tracker
receives SMS messages when it wakes up. To protect the tracker against
unauthorized messages each command must contain the Service PIN-
code - ХХХХ (factory default value is 1-1-1-1).
WARNING! WE RECOMMEND THAT YOU CHANGE THE DE-
FAULT VALUE OF THE SERVICE PIN-CODE
ХХХХ*PIN*YYYY* - Changing the “Service PIN-code”. This command
can be executed only from the phone number that has been previously
programmed in the tracker memory
ХХХХ – current PIN-code (default value is 1-1-1-1)
YYYY – new PIN-code.

AUTONOMOUS TRACKER PANDORA FINDER USER MANUAL
18 19
The tracker will answer - “PIN-code changed”after the command
execution.
XXXX*666* - Switching on the “Tracking mode”. The tracker will
activate the “Tracking mode”for a previously specied period or until a
command to switch it o would be received.
The tracker will answer - “Settings changed” after the command
execution.
ХХХХ*999* - Switching o the“Tracking mode”.
ХХХХ*ALARM*YYY* - Setting periodicity of communication.
YYY – hours value from 001 to 168.
The tracker will answer - “Settings changed” after the command
execution.
ХХХХ*500* - Request current location.
ХХХХ*100* - Request balance of the SIM-card.
ХХХХ*007* - Switching on the“Listening” function.
WARNING! MOST MOBILE PROVIDERS STORE UNDELIVERE
MESSAGES NO MORE THAN 24 HOURS.
REPLACING OR RECHARGING THE BATTARIES
When replacing or recharging the batteries, it is necessary to carefully
perform the following sequence of actions:
• Open the cover of the device;
• Replace the batteries;
• Insert the batteries keeping in mind the correct polarity.
• Close the cover;
• Activate the tracker in an open area with ne GPS signal.
WARNING! IT IS PROHIBITED TO RECHARGE THE BATTERIES
THAT ARE INCLUDED IN THE SYSTEM SET. IT IS RECOMMEND-
ED TO USE LITHIUM (LI-FES2) BATARIES ESPECIALY AT LOW
TEMPERATURES. ALKALINE BATARIES ARE ALSO ALLOWED;
DO NOT USE REGULAR ZINC-CARBON BATTERIES.
TRACKER INSTALLATION
The following conditions must be considered when installing the tracker:
• Good conditions for signals of the GPS/GLONASS receiver, GSM
modem, 2.4GHz radio interface (BLE4.2);
• Good conditions for the built-in microphone operation;
• The module must be rigidly xed in order to avoid damage and
movement while driving;
• The device must be installed in places where there are no any
liquids, condensate and high temperature;
• The module should be installed the front side up (the side with the
Pandora sign, the VALET button and the LED).

AUTONOMOUS TRACKER PANDORA FINDER USER MANUAL
20 21
WARRANTY OBLIGATIONS
The manufacturer guarantees correct operation of the device
if exploitation, installation, storage and transportation conditions
described in this manual were met.
The device should only be used according to the manual.
Parts malfunctioning during warranty period on the fault of the
manufacturer should be repaired or replaced by the installation center
of the manufacturer or by certied service center.
A user loses the right for warranty services in the following cases:
• when the warranty period expires;
• if exploitation, installation, storage or transportation conditions
• were not met;
• if there is mechanical damage of the external parts of the device
after it is sold. This includes: re damage, consequential damage in
case of car accident, aggressive liquids and water seeping damage,
damage caused by improper use;
• if the damage was caused with incorrect settings and parameter
adjustment;
• if there is no properly lled warranty card and installation certicate.
Warranty period is 3 years since the moment of purchase, but
no more than 3,5 (three and a half ) years since the moment of
production.
This warranty does not include batteries, as they have their own
service life time. Maintenances and repairs of the system with expired
warranty period are carried out at the expense of the user on separate
contracts between the user and the installer/service center

AUTONOMOUS TRACKER PANDORA FINDER USER MANUAL
22 23

WARRANTY CARD
Model Pandora Finder
Serial number____________________________________________
Date of purchase «______»______________20_____y.
Seller’s stamp
Seller’s signature _________________________________________
ACCEPTANCE CERTIFICATE
The Pandora Finder device is in conformity with Electromagnetic
compatibility Directive EMC 2004/108/EC and R&TTE Directive 1999/5/EC.
Serial number_____________________________________________
Date of production «______»______________20_____y.
Responsible person’s signature _____________________(stamp)
Packeger ______________________Signature_________________
(personal stamp)