PARANTEK DIM-F6110-POE User manual

DIM-F6110-POE
www.parantek.com
IP MINIATURE CAMERA
Main Features
Specifications
§1/2.9" 2.19M Sony Exmor CMOS Sensor
§2Mega Pixels (Max. 1080p25/30)
§Fixed Board Lens
§Providing Cable type POE
§Onvif Ver. 2.4 Compatible with H.264, MPEG4 and MJPEG
§Box Miniature Housing(37x37) with U type swivel bracket
Model DIM-F6110-POE
Signal System IP (Network) – Embedded Linux
Pickup Device 1/2.9”(D-6.23mm) 2.1M SONY Exmor CMOS Sensor
Scanning System Progressive Scan (16:9)
Total Pixels 2.24M [2000(H)x1121(V)]
Active Pixels 2.12M [1936(H)x1097(V)]
Min. Illumination 0.2Lux
No. of IRED N/A
Video Out (RJ45)
Up to 30fps @ 1920x1080p
(1920x1080, 1280x1024, 1280x960, 1280x720,
1024x768, 640x480, 320x240)
Lens Fixed f=3.6mm board type, F2.5
Lens (Mount) Board type (M12)
Angle of View 105.5˚(D), 89˚(H), 48.5˚(V)
OSD Via Webpage Viewer
Camera Title Off, On(Max. 10 Characters)
Language English, Korean
Exposure AE, Manual
White Balance Auto, Indoor, Outdoor, Fluorescent
DWDR Off, On(1 ~ 5 Steps)
Day & Night Mode Auto, Day, Night, EXT.
Electronic Shutter 1/25(30)~1/15,000sec
Noise Reduction Off, On (1~63 Setps)
DSS(Sens-up) N/A
Mirror Off, On(Mirror, Flip, Both)
Other Features Motion Detection(48 Zones), Privacy Mask(6 Zones) etc.
Network Protocol
TCP/IP, UDP/IP, RTP, RTSP, RTCP, NTP, HTTP
DHCP, FTP, SMTP, DNS, DDNS
Onvif 2.4 Compatible
At-a-time Access Maximum 10 users
Video/Audio Codec H.264, MPEG4, MJPEG / G.711 (Triplex Streaming)
Sensor In/Alarm Out N/A
Audio Line In/Out N/A
Power Source DC12V / POE (POE Cable: 800mm±15mm)
Power Consumption
Less than 2.5Watts (170mA)
Operating Temp. -10℃ ∼55℃(Humidity :0%RH ∼90%RH)
Size (mm) 38.5(W)x37(D) (without Bracket)
Weight 143 g (gift-box packing)
Dimension
Option
§Lens (Fixed)
f=1.4mm(Fish-eye 180°), 2.1mm, 2.5mm, 2.8mm,
4mm, 6mm, 8mm, 12mm, 16mm, 25mm

•IP camera connection
Connect LAN cable to RJ45 jack of camera
Connect the other end LAN cable to RJ45 jack of router or hub
If you are not using POE switcher to provide the power to the IP camera, connect regulated a DC12V
power adaptor to the IP camera.
Wait for about 50 seconds until the camera initialization is completed
Factory Default IP address is 192.168.1.30
Factory Default ID & Password are admin / admin.
•Using IP manager
You can simply change the IP address by using ‘IP Manager’ provided.
Run IP manager as administrator.
click “Find” button when the IP camera is connected to your PC or network, all IP address will appear.
Choose & change the IP address of camera you want to change and click “change” Button
After click the “change” button left window will be
appeared. Once you click “change” button, the camera
will reboot for 10second.
After reboot the camera, the changed IP address will be
applied and appeared.
•Checking Video by Web Viewer
Run web browser and Input the IP address which
taken from IP manager.
•Supported O/S & Web Browser
- O/S : Windows7, 8, 10, MAC
- Browser : Internet Explorer 11 or higher, Firefox,
Safari, Opera
* Monitoring videos can be operative only under IE
with Active-X installation.
DIM-F6110-POE
www.parantek.com
IP MINIATURE CAMERA

Camera Mounting Instruction
• There are three(3) of each Ø3xL10
screw and M2xS/PW4 screw
together with a swivel bracket in
the accessory package.
• Please use two(2) of the screws
as shown left. We are providing
one of each extra screw in the
package.
• If you do not use M2xS/PW4
screws provided, it will damage
the camera board inside housing.
Such the damage will be your
responsibility.
Dimension of POE on cable
Function I/O Note Remarks
POWER IN Camera power input (Not required when POE works) DC12V
VIDEO/POE/CONTROL IN/OUT H.264 video output, Power over Ethernet, Control (RJ45)
2
1
1
2
GND DC12V