PARANTEK DIS-T910 Installation guide

DIS-T910
IP STANDARD BOX CAMERA
Main Features
Specifications
Dimension
Option
§Lens (C/CS)
- DC Auto IRIS Manual
- Motorized Zoom
§1/2.8" 2.9μm Pixel Sony Starvis WDR CMOS Sensor
§2Mega Pixels (Max. 1080p25/30)
§C / CS Lens Mountable
§TDN ICR Mechanism Built-in
§WDR / 3D-NR Supported
§POE Interface Built-in
§Onvif Ver. 17.06 Compatible with H.265, H.264 and MJPEG
§Analog Composite Video Out
www.parantek.com
Model DIS-T910
Signal System IP (Network) – Embedded Linux
Pickup Device 1/2.8”(D-6.4mm) 2.13M SONY Starvis CMOS Sensor
Scanning System Progressive Scan (16:9)
Total Pixels 2.16M [1945(H)x1109(V)]
Active Pixels 2.13M [1945(H)x1097(V)]
Min. Illumination 0.06Lux(F2.5 – 30IRE), 0.03Lux(ICR on)
TDN Yes (ICR Mechanism)
Video Out (RJ45)
Up to 30fps @ 1920x1080p
(1920x1080, 1280x1024, 1280x960, 1280x720,
1024x768, 640x480, 320x240)
Lens Option
Lens (Mount) C / CS type
Angle of View N/A
OSD Via Webpage Viewer
Camera Title Off, On(Max. 10 Characters)
Language English
Exposure DC, Manual
White Balance Auto(Indoor), Auto(Outdoor), Push, User
WDR Off, On
Day & Night Mode Auto, Day, Night, ICR Control
Electronic Shutter 1/(25)30~1/30,000sec
Noise Reduction Off, On (2D-NR, 3D-NR)
DSS(Sens-up) N/A
Mirror Off, On(Mirror, Flip, Both)
Other Features
Motion Detection
(432 Zones), Privacy Mask(16 Zones)
etc
Network Protocol
TCP/IP, UDP/IP, RTP, RTSP, RTCP, NTP, HTTP
DHCP, FTP, SMTP, DNS, DDNS
Onvif 17.06 Compatible
At-a-time Access Maximum 10 users
Video/Audio Codec H.265, H.264, MJPEG / G.711 (Triplex Streaming)
Sensor In/Alarm Out Option (1 / 1)
Audio Line In/Out 1 / 1 (Two-way Audio)
Power Source DC12V / POE Built-in
Power Consumption
Less than 2.9Watts (240mA)
Operating Temp. -10℃ ∼55℃(Humidity :0%RH ∼90%RH)
Size (mm) 71(W) x 58(H) x 127(D)
Weight 466 g (gift-box packing)

DIS-T910 QUICK MANUAL
(1) Reset Switch
In order to reset the IP camera, push the switch down and hold for over seven seconds
(2) Audio In
Line Input
(3) LAN
RJ45 Female connector
(4) Audio Out
Line Output
(5) CVBS Video Out Connector
Sends CVBS video signal and connects to the video input terminal of the CVBS monitor or
CVBS DVR
(6) Multi-port Terminal
Connect to the power, External D&N port and Alarm Input & Output ports properly.
Camera power input is not required when POE works.
www.parantek.com
A.I & A.O
Alarm Input (3.3V)
External D&N Input (3.3V)
GND
For External D&N Input
For Alarm In & Out
(6)
(1)
(2) (4)
(5)
(3)

•IP camera connection
Connect LAN cable to RJ45 jack of camera
Connect the other end LAN cable to RJ45 jack of router or hub
If you are not using POE switcher to provide the power to the IP camera, connect regulated a DC12V
power adaptor to the IP camera.
Wait for about 50 seconds until the camera initialization is completed
Factory Default IP address is 192.168.1.30
Factory Default ID & Password are admin / admin.
•Using IP manager
You can simply change the IP address by using ‘IP Manager’ provided.
Run IP manager as administrator.
click “Find” button when the IP camera is connected to your PC or network, all IP address will appear.
Choose & change the IP address of camera you want to change and click “change” Button
After click the “change” button left window will be
appeared. Once you click “change” button, the camera
will reboot for 10second.
After reboot the camera, the changed IP address will be
applied and appeared.
•Checking Video by Web Viewer
Run web browser and Input the IP address which
taken from IP manager.
•Supported O/S & Web Browser
- O/S : Windows7, 8, 10, MAC
- Browser : Internet Explorer 11 or higher, Firefox,
Safari, Opera
* Monitoring videos can be operative only under IE
with Active-X installation. Make sure to use an
Administrator mode for installing Active-X.
DIS-T910
IP STANDARD BOX CAMERA
www.parantek.com