Patio Premier 217005 User manual

Cast Bistro Set
Instruction Manual
Due to ongoing product development
the actual product or products may vary from
the illustrations or photos shown within this manual.
NOTE: This product is intended for residential, non-commercial use.
For Manuals, Replacement Parts or Customer Service visit:
www.ezreplacement.com
Additional Limitations
Limited Warranty
Made in China
©2017 J & J Global, LLC
Distributed By:
J & J Global, LLC
Carrollton, TX 75006
Model No: 217005, 207004
Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
For warranty information, please refer to the back page
of this instruction manual.
J & J Global (Seller) warrants to the original Buyer only, that each product will be free from defects in material and
workmanship for a period of one (1) year from date of purchase. SELLER’S SOLE OBLIGATION AND BUYER’S
EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT
CHARGE, WHICH ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE SELLER
WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY FROM REPAIRS OR
ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSON; IMPROPER MAINTENANCE, NEGLECT OR ACCIDENT ARE
NOT COVERED BY THIS LIMITED WARRANTY. This warranty does not apply to damage, heat-induced coloration
changes, scratching or alteration due to normal use or weathering. To make a claim under this Limited Warranty,
email [email protected] or visit www.ezreplace- ment.com for warranty questions and claims.
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED TO THIS PRODUCT.
ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1) YEAR FROM DATE OF PURCHASE. IN NO
EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT
LIMITED TO LIABILITY FOR LOSS OF PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such provision shall
not a ect any other provision herein, this Limited Warranty shall be construed as if such invalid and/or unenforce-
able provision had never been contained herein.
This warranty gives you special legal rights, and you may also have other rights which vary from state to state.
This warranty contains the entire agreement between Seller and Buyer and supercedes any and all prior
agreements, arrangements, or understandings between the parties relating to product warranty.

Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
NOTE: This product is intended for residential, non-commercial use.
DE
FGHJ
1 2
A 2
B
Chair Back
2
C
Chair Seat
8
D
Chair Leg
1
E
Table Top
3
F
Table Leg
1
G
Table Center Brace
26
H
Stud, M8 x 30
3
I
Bolt, M8 x 30
29
J
Washer, M8
Nut, M8 29
PARTS & HARDWARE LIST
PART # DESCRIPTION QUANTITY
A
BC
I
ASSEMBLY INSTRUCTIONS
Figure 1
A
B
C
G
G
J
I
CAUTION: Do not over tighten fasteners.
1. (SEE FIGURE 1) Thread studs (G) into holes on bottom of chair back (A). Insert studs (G) on chair
back (A) through holes on chair seat (B) top side.
2. With chair back (A) in place, thread studs in bottom holes of chair seat (B) next to studs of chair
back. Insert chair leg (C) onto chair seat (B) studs, connecting the chair back, seat and leg.
3. Secure leg, seat and back with washers (I) and nuts (J).
4. Attach remaining legs, repeat step 2 and step 3.
5. Assembly second chair in same manner, repeat steps 1 - 4.

3 4
ASSEMBLY INSTRUCTIONS
Figure 2
D
E
E
G
I
J
6. (SEE FIGURE 2) Position table top (D) upside down on a clean surface. Thread studs (G) into holes
on bottom of table top (D).
7. Place the holes at top of leg (E) over threaded studs (G) on bottom of table top (D).
8. Secure using washers (I) nuts (J). Do not over tighten fasteners.
9. Attach remaining legs, repeat step 7 and step 8.
10. (SEE FIGURE 3) Position table right side up.
11. Place table center brace (F) on top of tabs on table leg (E) and align holes.
12. Insert bolt (H) through top of table center brace (F) and table leg tab. Secure with washer (I) and
nut (J). Do over tighten fasteners.
Figure 3
E
I
H
J
F
F