Patlite SZK Series Installation and operation manual

1
Thank you very much for purchasing our Patlite products.
●Request the installation and wiring be performed by a professional contractor if construction work is involved.
● Prior to installation, read this manual thoroughly before using this product to ensure correct use. In addition, please
store this manual for future reference when performing maintenance, repairs or inspections.
● If there are any questions concerning this product, refer to the contact information at the end of this document and contact
your nearest PATLITE Sales Representative.
WebManual
WallMountBracket/CeilingMountBracket
RubberGasket/UpperBracket/NPTBracket
GA000146202
TYPE SZK / SZW / SZP
● Read this manual carefully prior to installation.
Notice to Customer
To the Contractor
(Top：Product Name Bottom：Model)
SZK-101
Wall Mount Bracket
SZK-102
Wall Mount Bracket
SZK-105
SZK-104
SZK-103
Wall Mount Bracket Wall Mount Bracket Cover
Wall Mount Bracket Cover Ceiling Mount Bracket
SZW-101
SZP-103
NPT Bracket
Rubber Gasket Rubber Gasket
SZW-103
SZW-102
Applicable Models
1. Be sure to read the instruction manual included with the Applicable Models in addition to this model.
RotatingBeaconsSK , Multi-functionBeaconsSF , FlashingBeaconsSL
〈Note〉
This product is an optional part for use in combination with its Applicable Models.
SZP-101
Upper Bracket
SZP-102
NPT Bracket
SZP-104
NPT Bracket

2
● To prevent from damage, observe the following:
- Use this product in a properly maintained condition.
● Request the installation and wiring be performed by a professional contractor if construction work is involved.
Failure to comply may result in fire, electric shock or falling from high places possible cause of failure may occur.
● When this product is used for security purposes, it should beinspecteddaily.
● After installation, do not use this product to climb up onto the equipment with.
Failure to comply will result in product damage and/or falling off the machinery.
● Useasoftcloth,etc.,dampenedwithwatertowipetheproduct.
Donotusecleanerscontainingthinnerbenzinegasoline,oil,Chemicals,etc.,towipewith.
Itmayresultindiscolorationanddeterioration.
●Toensuresafetywhenthisoptionalpartisinstalledintoequipment,observethefollowing:
- Donot,byanymeans,disassembleormodifythisproduct.
● Donotdisassembleorremoveduringoperation.
ReadthisFirst
1
NOTES TO BE OBSERVED FOR SAFE OPERATION
Warning
Caution
Indicates an imminently dangerous condition:
failure to follow the instructions may lead to
death or serious injury.
Indicates a potentially dangerous condition:
failure to follow the instructions may lead to
slight injury or property damage.
In order to prevent any damage to the user and other personnel or to assets, note the following:
■ The degree of harm and damage that will occur when misuse is made by ignoring the contents of the icons indicated is
explained below.
Warning
Notice
Caution

3
Name and Dimensions
2
Unit：mm
Cable Exit Hole
125
75
104
91.5
71.5
26
Cable gland
Mounting Hole
Product Mounting Hole 2 Places
SF08-M□KT□/SL08-M□KT□
Product Mounting Hole 2 Places
SF10-M□KT□/SL10-M□KT□
Product Mounting Hole 3 Places
SF08-M□JN/SL08-M□JN
SKS-M□J
Product Mounting Hole 3 Places
SF10-M□JN/SL10-M□JN
SKH-M□J□/SKH-M□T□
TYPE
SZK-101
※The Product Mounting Holes and Cable gland Mounting Holes are perforated.
Check 「Product Mounting with Knock-outs (11 page)」for how to drill holes.
45
Mounting Hole
86
①
②
16
70 4-6.5
No. Material
PC
1Wall Mount Bracket
Name
CR
2Waterproof Sheet t = 1.0

4
TYPE
SZK-102
Product Mounting Hole 3 Places
SF08-M□JN/SL08-M□JN
SKS-M□J
Product Mounting Hole 3 Places
SF10-M□JN/SL10-M□JN
SKH-M□J□/SKH-M□T□
Product Mounting Hole 2 Places
SF10-M□KT□/SL10-M□KT□
112.5
65.5
24
35
61
95
35
24
Product Mounting Hole 2 Places
SF08-M□KT□/SL08-M□KT□
Wall Mount Bracket Cover
Mounting Hole 2 Places
SZK-104
Unit：mm
98
146
174.5
103.5
Wall Mount Bracket Cover
Mounting Hole 2 Places
SZK-105
Product Mounting Hole 3 Places
SL15-M□KTN/SL15-M□JN
SKP-M□J
43.5 44
TYPE
SZK-103
3122
38
Mounting Hole
Cable Exit Hole
Cable Exit Hole
Mounting Hole
49
70
19
60
130
75
75
Mounting Hole
34
t = 2.0
t = 2.0
①
①
13
R2.1
35
35
4-7
4-6
Material
SUS
No.
1Wall Mount Bracket
Name
Material
SUS
No.
1Wall Mount Bracket
Name

5
Accessory
SUS
Head Tapping Screw
4×12 2 pcs.
Material
TYPE
SZK-104
Unit：mm
TYPE
SZK-105
103
80
22
115
65
(15)
64
177.5
102.5
35.5
126
157
(23)
102
Wall Mount Bracket
Mounting Hole 2 Places
SZK-102
Wall Mount Bracket
Mounting Hole 2 Places
SZK-103
①
①
No. Material
PC
1Wall Mount Bracket Cover
Name
No. Material
PC
1Wall Mount Bracket Cover
Name
Accessory
SUS
Head Tapping Screw
5×16 2 pcs.
Material

6
TYPE
SZW-101
Unit：mm
20
Cable Exit Hole
Product Mounting Hole 3 Places
SF10-M□JN/SL10-M□JN
SKH-M□J□/SKH-M□T□
Product Mounting Hole 2 Places
SF10-M□KT□/SL10-M□KT□
Mounting Hole
90°
t = 1.2
①
35
135
105
150
4-6
Upright
Inverted
Material
SPCE
No.
1Ceiling Mount Bracket
Name

7
TYPE
SZW-102
Unit：mm
TYPE
SZW-103
10.5
Product Mounting Hole 3 Places
SF08-M□JN/SL08-M□JN
SKS-M□J
11
Product Mounting Hole 3 Places
SF10-M□JN/SL10-M□JN
SKH-M□J□/SKH-M□T□
Cable Exit Hole
Cable Exit Hole
①
①
100
80
Material
Silicone
No.
1Rubber Gasket
Name
Material
Silicone
No.
1Rubber Gasket
Name

8
TYPE
SZP-101
単位：mm
41
Pole
Product Mounting Hole 3 Places
SF10-
M□ JN/SL10- M□ JN
SKH-
M□ J□/SKH- M□ T□
Product Mounting Hole 2 Places
SF10-M□KT□/SL10-M□KT□
( )
Pole Mounting Hole 2 Places
33
Cable Exit Hole
①
100
31.5
22
No. Material
PC
1Upper Bracket
Name
Accessory
SiliconePole Waterproof Sheet 1 pcs.
Material
PURWaterproof Sheet t =2.0 1 pcs.

9
TYPE
SZP-102
Unit：mm
30
Product Mounting Hole 2 Places
SF08-M□KT□/SL08-M□KT□
Product Mounting Hole 3 Places
SF08-M□JN/SL08-M□JN/SKS-M□J
30
TYPE
SZP-103
Product Mounting Hole 2 Places
SF10-M□KT□/SL10-M□KT□
Product Mounting Hole 3 Places
SF10-M□JN/SL10-M□JN
SKH-M□J□/SKH-M□T□
1/2”NPT Internal Threads
1/2”NPT Internal Threads
Cable Exit Hole
Cable Exit Hole
3-14
3-12
15
15
100
80 ①
No. Material
AL
1NPT Bracket
Name
①
No. Material
AL
1NPT Bracket
Name

10
TYPE
SZP-104
Unit：mm
30
3/4”NPT Internal Threads
Product Mounting Hole 3 Places
SL15-M□KTN
Product Mounting Hole 3 Places
SL15-M□JN/SKP-M□J
Cable Exit Hole
15
150
3-18
①
No. Material
AL
1NPT Bracket
Name

11
Installation
3
Notice
● Ensure that the product is installed in an environment that meets the following conditions:
- Where excessive vibration is not present.
- On a sturdy surface. - On a level surface.
●When installing this product in an environment where waterproofing is required,
be sure to properly waterproof the exposed nuts and bolts.
●Before use, be sure to read this manual as well as the instruction manual for the compatible PATLITE beacon.
TYPE
SZK-101
□For Product Mounting Holes
Place the mounting bracket on a flat surface, with the bottom side up. Drill the holes from the bottom side.
□For Cable Gland
Drill a 16 hole from the top surface.
CableglandMountingHoleProductMountingHole(2holes)
(SF10-KT/SL10-KT)
ProductMountingHole(3holes)
(SF10-J/SL10-J/SKH)
Drill
Model
SF08-KT/SL08-KT
SF10-KT/SL10-KT
SF08-J/SL08-J/SKS
SF10-J/SL10-J/SKH
Number of Holes
2
2
3
3
Connect a commercially available cable gland
from the bottom of the Wall Mount Bracket.
Install and fix in placewith nuts from above.
CableglandInstallation
ProductMountingwithKnock-outs
●Ifusingacablegland,besurethatyouareusingitforthecabletypebeacons.
●Donotopenunusedmountingholes.Ifitisaccidentallyopened,besuretowaterprooftheopening.
●Besuretodeburrafterdrilling.
●AcableglandwithamountingscrewsizeofM16x20mmorlessandcablesizeof 7to8mmisrecommended.
Caution
5mm
6mm
5mm
6mm

12
■Mounting Dimensional Drawing［Unit：mm］
Mounting Hole
Wiring Hole
3-screw Mounting Type
① Attach the Wall Mount Bracket to the wall, referring to
the dimensions in the Mounting Dimensional Drawing below.
(Screws are not included. Please prepare separately.)
② If using a cable gland, refer to “Product Mounting
with Knock-outs (page 11)”.
③ If using a Rubber Gasket (SZW-102 / SZW-103),
waterproofing is required.
 (Refer to “Product Attachment (page 17)” for
mounting instructions for the Rubber Gasket.)
④ Wire the product as shown on the right.
⑤ Insert the product bolt into the mounting hole of the Wall Mount Bracket.
⑥ Use the nuts and washer (accessory) to secure the product.
① Attach the Wall Mount Bracket to the wall, referring to
the dimensions in the Mounting Dimensional Drawing below.
(Screws are not included. Please prepare separately.)
② Using the mounting holes on the Wall Mount Bracket, secure
the Mounting Bracket and Waterproof Sheet with screws and nuts.
(Installation screws and nuts are not included with this product. )
③ Wire the product as shown on the right.
④ Check that the O-ring is not twisted.
⑤
Align the indicators of the Mounting Bracket and the body of the beacon,
then twist clockwise to lock in place.
(Read the applicable instruction manual for the locked state.)
Recommend
Torque
M4
M5
0.7N･m
1.4N･m
□ 3-screw Mounting Type
□ 2-point Hole Type Mounting
Rubber
Gasket
⑥
⑤
③
With Cable Gland Without Cable Gland
②④ ④
2-point Hole Type Mounting
Waterproof Sheet
③
②
⑤
④
Model
SF08/SL08
SF10/SL10
Recommend
Torque
0.7N･m
1.4N･m
Recommend
Screw
M4×20mm
M5×20mm
Recommend
Torque
1.4N･m
Screw / Nut
M5
15
70
4-6
Model
SF08/SL08/SKS
SF10/SL10/SKH
Mounting Bracket
O-ring
Product Attachment
Nut

13
Recommend
Torque
Model
Model Recommend
Torque
Recommend
Screw
Recommend
Torque
Screw / Nut
■Mounting Dimensional Drawing［Unit：mm］
TYPE
SZK-102
2-point Hole Type Mounting
3-screw Mounting Type
38
70
3
Mounting Hole
Wiring Hole
22
① Attach the Wall Mount Bracket to the wall, referring to
the dimensions in the Mounting Dimensional Drawing below.
(Screws are not included. Please prepare separately.)
② Insert the product bolt into the mounting hole of the Wall Mount Bracket.
③ Use the nuts and washer (accessory) to secure the product.
□
3-screw Mounting Type
①Attach the Wall Mount Bracket to the wall, referring to
the dimensions in the Mounting Dimensional Drawing below.
(Screws are not included. Please prepare separately.)
②Using the mounting holes on the Wall Mount Bracket, secure
the Mounting Bracket and Waterproof Sheet with screws and nuts.
(Installation screws and nuts are not included with this product. )
③Check that the O-ring is not twisted.
④
Align the indicators of the Mounting Bracket and the body of the beacon,
then twist clockwise to lock in place.
(Read the applicable instruction manual for the locked state.)
□
2-point Hole Type Mounting
③
②
Waterproof Sheet
Mounting Bracket
O-ring
●When using the Wall Mount Bracket (SZK-102) with a Rubber Gasket (SZW-102/SZW-103), the protection rating is IP23.
●If the rated voltage of the product to be installed exceeds 100V AC, use the Wall Mount Bracket Cover (SZK-104).
SF08/SL08
SF10/SL10
0.7N･m
1.4N･m
M4×20mm
M5×20mm
SF08/SL08/SKS
SF10/SL10/SKH
M4
M5
0.7N･m
1.4N･m
1.4N･mM5
②
③
④
15
4-6
Caution
Product Attachment
Nut

14
Recommend
Torque
Screw / Nut
Model Recommend
Torque
Recommend
Screw
Recommend
Torque
Model
① Attach the Wall Mount Bracket to the wall, referring to
the dimensions in the Mounting Dimensional Drawing below.
(Screws are not included. Please prepare separately.)
② Insert the product bolt into the mounting hole of the Wall Mount Bracket.
③ Use the nuts and washer (accessory) to secure the product.
■Mounting Dimensional Drawing［Unit：mm］
TYPE
SZK-103
① Attach the Wall Mount Bracket to the wall, referring to
the dimensions in the Mounting Dimensional Drawing below.
(Screws are not included. Please prepare separately.)
② Using the mounting holes on the Wall Mount Bracket, secure
the Mounting Bracket and Waterproof Sheet with screws and nuts.
(Installation screws and nuts are not included with this product. )

③ Check that the O-ring is not twisted.
④
Align the indicators of the Mounting Bracket and the body of the beacon,
then twist clockwise to lock in place.
(Read the applicable instruction manual for the locked state.)
□
3-point Hole Type Mounting
3-point Hole Type Mounting
3-screw Mounting Type
60
130
Wiring Hole
Mounting Hole
30
□ 3-screw Mounting Type
③
②
②
④
③Waterproof Sheet
Mounting Bracket
O-ring
●If the rated voltage of the product to be installed exceeds 100V AC, use the Wall Mount Bracket Cover (SZK-105).
Caution
2.4N･mM6
SL15/SKP Ｍ8 6.0N･m
6.0N･m M5×25mm
SL15
4-7
15
Product Attachment
Nut

15
① Remove the accessories attached to the Wall Mount Bracket Cover.
② Insert the Wall Mount Bracket Cover into the Wall Mount Bracket
as shown in Figure 1.
③ Align the Mounting Holes on the Wall Mount Bracket and
the Wall Mount Bracket Cover.
④ Secure the Wall Mount Bracket Cover with the screws provided.
TYPE
SZK-104/SZK-105
④
Model
SZK-102
SZK-103
Screw Recommend
Torque
4×12mm
5×16mm
0.7N･m
1.4N･m
Wall Mount Bracket Attachment
②
③
Figure 1
Figure 2
●Attach the Wall Mount Bracket cover after attaching the product to the Wall Mount Bracket (SZK-102 / SZK-103).
(Refer to “Product Attachment (page 13, 14)” for the mounting method of the Wall Mount Bracket.)
Caution

16
Recommend
Torque
Screw / Nut
Model Recommend
Torque
Recommend
Screw
Recommend
Torque
Model
TYPE
SZW-101
■Mounting Dimensional Drawing［Unit：mm］
Wiring Hole
90°
Mounting Hole
SF10/SL10/SKH M5 1.4N･m
3-screw Mounting Type
2-point Hole Type Mounting
① Insert the product bolt into the mounting hole of the Ceiling Mount Bracket.
② Use the nuts and washer (accessory) to secure the product.
③ Attach the Ceiling Mount Bracket to the wall, referring to
the dimensions in the Mounting Dimensional Drawing below.
(Screws are not included. Please prepare separately.)
□
3-screw Mounting Type
① Using the mounting holes on the Ceiling Mount Bracket, secure
the Mounting Bracket and Waterproof Sheet with screws and nuts.
(Installation screws and nuts are not included with this product. )

② Check that the O-ring is not twisted.
③
Align the indicators of the Mounting Bracket and the body of the beacon,
then twist clockwise to lock in place.
(Read the applicable instruction manual for the locked state.)
④ Attach the Ceiling Mount Bracket to the wall, referring to
the dimensions in the Mounting Dimensional Drawing below.
(Screws are not included. Please prepare separately.)
□
2-point Hole Type Mounting
②
①
①
③
②
Waterproof Sheet
Mounting Bracket
O-ring
SF10/SL10/SKH 1.4N･m
M5×20mmor
M5×14mm
●After installing the product, fix the Ceiling Mount Bracket to the ceiling.
Caution
1.4N･mM5
4-6
15
135
Product Attachment
Nut

17
Nut Recommend
Torque
Model
Nut Recommend
Torque
Model
TYPE
SZW-102/SZW-103
SF08/SL08/SKS M4 0.7N･m
① Align the opening of beacon base with the opening of the Rubber Gasket as shown below.
② Insert the product bolt into the mounting hole of the Rubber Gasket.
③ Use the nuts and washer (accessory) to secure the product.
SF10/SL10/SKH M5 1.4N･m
SZW-102
SZW-103
Opening of Beacon Base
Opening of Rubber Gasket
■Mounting Dimensional Drawing［Unit：mm］
□SZW-102
□SZW-103
Mounting Hole

Wiring Hole
Wiring Hole
Mounting Hole
120°
120°
③
②
50
70
15
15
3-5

3-6
Product Attachment

18
Model Recommend
Torque
Recommend
Screw
Nut Recommend
Torque
Model
TYPE
SZP-101
① Install the Pole Waterproof Ring to the bottom of the Upper Bracket.
Check that the 2 ribs are on the outside.
② Insert the Pole into the Upper Bracket. Refer to the figure on the right.
(The Pole is sold separately. )
③ Tighten the Binding Head Tapping Screws (2 pcs.) from
the topside of the Upper Bracket.
□ 3-screw Mounting Type
SF10/SL10/SKH M5 1.4N･m
① Wire the product as shown on the right.
② When use a Rubber Gasket (SZW-103),waterproofing is required.
 (Refer to “Product Attachment (page 17)” for
the mounting method of the Rubber Gasket.)
③ Insert the product bolt into the mounting hole of the Upper Bracket.
④ Use the nuts and washer (accessory) to secure the product.
※ The Waterproof Sheet is not required.( Accessory of Upper Bracket )
① Wire the product as shown on the right.
② Using the mounting holes on the Upper Bracket, secure
the Mounting Bracket and Waterproof Sheet with screws and nuts.
(Installation screws and nuts are not included with this product. )
③ Check that the O-ring is not twisted.
④
Align the indicators of the Mounting Bracket and the body of the beacon,
then twist clockwise to lock in place.
(Read the applicable instruction manual for the locked state.)
□
2-point Hole Type Mounting
3-screw Mounting Type
2-point Hole Type Mounting
Pole Waterproof Ring
Pole
Rubber Gasket
Waterproof Sheet
(for Beacon)
Waterproof Sheet
(for Upper Bracket)
③
①
②
④
③
②
②
③
④Mounting Bracket
O-ring
①
①
1.4N･m M5×20mm
SF10/SL10/SKH
Screw Recommend
Torque
3×12mm 0.8N･m
Product Attachment
Pole Attachment
Upper Bracket

19
TYPE
SZP-102/SZP-103/SZP-104
①Install the Pole to the NPT Bracket.
Tighten tightly !
□3-screw Mounting Type
① Take out the wiring.
② If using a Rubber Gasket (SZW-102 / SZW-103),
waterproofing is required.
(Refer to “Product Attachment (page 17)” for
mounting instructions for the Rubber Gasket.)
③ Insert the bolts of the beacon into the mounting holes of t
ihe NPT Bracket.
④ Use the nuts (accessory) to secure
the mounting surface of the NPT Bracket.
① Using the mounting holes on the NPT Bracket, secure
the Mounting Bracket and Waterproof Sheet with screws and nuts.
(Installation screws are not included with this product.
Binding head screws or pan head screws are recommended.)
② Take out the wiring.
③ Check that the O-ring is not twisted.
④
Align the indicators of the Base and the body of the beacon,
then twist clockwise to lock in place.
( Check the INSTRUCTION MANUAL for the lock state )
3 - point Hole Leg Mounting Type
PoleInstallation
ProductAttachment
External Thread
Model
SZK-102
SZK-104
SZK-103
1/2 NPT
3/4 NPT
1/2 NPT
External Thread
3-screw Mounting Type
④
③
②
2 - point Hole Leg Mounting Type
①
③
④
WaterproofSheet
Mountingbracket
ORing
RubberGasket
Model
SF08/SL08/SKS
SF10/SL10/SKH
SL15/SKP
Nut Recommended
Torque
M4
M5
M8
0.7 N•m
1.4 N•m
6.0 N•m
Model
SF08/SL08
SF10/SL10
SL15
0.7 N•m
1.4 N•m
6.0 N•m
M4
M5
M8
Recommended
Torque
□2 - point Hole Leg Mounting Type
Screw
①
②
①

20
Specifications
4
General Specifications（SZK-101）
Product Name Wall Mount Bracket
Model SZK-101
Applicable Models
Upright
Mounting Location
Mounting Direction
According to the product to be installed.
Upright
Mass (Typ.) 0.15kg
Protection Rating
SL08-M□KT□
SF08-M□KT□
SF10-M□KT□
SL10-M□KT□
SF08-M□JN
SL08-M□JN
SKS-M□J
SF10-M□JN
SL10-M□JN
SKH-M□J□
SKH-M□T□
Environmental
Condition
There are no contents of controlled substances exceeding the threshold for the RoHS Directive.
Remarks ※Excluding Terminal Block Opening of SKH-M□T.
IP65
(With product attachment)
IP23 ※
(With product attachment)
IP65
(When used with product and SZW-102
Rubber Gasket attachment)
IP65
(When used with product and SZW-103
Rubber Gasket attachment)
SF08-M□KT□/SL08-M□KT□
SF10-M□KT□/SL10-M□KT□
SF10-M□JN/SL10-M□JN
SKH-M□J□/SKH-M□T□
SF08-M□JN/SL08-M□JN/SKS-M□J
SF08-M□JN/SL08-M□JN/SKS-M□J
SF10-M□JN/SL10-M□JN
SKH-M□J□/SKH-M□T□