Patriot 355-0608 User manual

PAGE: 1 / 10
220817

PAGE: 2 / 10
A. 16-1/4" B. 12-3/4" C. 52" D. 5"
Remote Control Instructions
Unpack your fan and check the contents. You should have the following items.
9
10
X 7
11 12
Dimension Reference (Installed with 6" Downrod)
1.) Hanger Bracket
2.) Canopy
3.) Decorative Cap (Remove the Preassembled Decorative Cap from the Canopy Before Installation.)
4.) Downrod Set (Included Hanger Ball, 6" Downrod, Hanger Pin & Lock Pin)
5.) Fan Motor Assembly
6.) Fan Blades (3PCS)
7.) Light Kit with LED Module
8.) Glass Shade
9.) Connect Plate of Light Kit
10.) Remote Control Set (Includes Receiver & Transmitter & Wire Connectors & Battery
& Screws & Remote Control Instructions)
11.) Assembly Kit
12.) Installation Instructions
220817

PAGE: 3 / 10
Connect Plate of Light Kit
220817

PAGE: 4 / 10
220817

PAGE: 5 / 10
Note: For sloped ceiling installation, make
sure that the chip of the hanger bracket
is toward the floor.
IMPORTANT:
BEFORE YOU BEGIN INSTALLATION, CAREFULLY READ ALL INFORMATION PROVIDED IN THE SAFETY
INSTRUCTIONS AND INSTALLATION INSTRUCTIONS. IF IN DOUBT, CONSULT A QUALIFIED
ELECTRICIAN.
SAVE ALL INSTRUCTIONS.
Tighten the two collar screws.
Slide lock pin into hanger pin until
it is locked into position.
Remove the lock pin from hanger
pin and remove the hanger pin
from the downrod.
Turn OFF the electric circuit at the
main fuse or circuit breaker box.
Thread the motor wires through
the decorative cap (Making sure
the smooth side of decorative
cap is facing downward.), canopy
and downrod.
Loosen the collar screws out part way.
Insert the downrod into the collar.
Slide hanger pin through holes of
collar and downrod.
Hang the fan on hanger bracket, and
make sure the slot of hanger ball is
snapped into the chip of hanger bracket
exactly.
Note: For sloped ceiling installation,
make sure the slot of hanger ball and
the chip of hanger bracket face down.
Tighten the hanger bracket to the outlet box
with two mounting screws. (To reduce the
risk of fire, electric shock, or personal injury,
mount to an outlet box marked "Acceptable
for fan support" and use mounting screws
provided with the outlet box.)
Downrod
220817

Move ground wires (a), outlet box wires (b), and motor
wires (c) away from the center of the hanger bracket.
Then slide receiver through hanger bracket as shown.
Antenna end first, until it is placed in the centered.
Finally, cut motor wires (c) to length needed for
connections.
G
Code example:
1-ON 2-OFF 3-ON 4-OFF on both SUR
Switches.
Note: If you have two ceiling fans with
2 remote control units, set 2 different
codes for each set of transmitter / receiver.
Both the transmitter and receiver have a 4-key
unit code on each SUR Switch (Fig.8) and by
default, all keys are pre-set to the "off" position.
This means that the transmitter and receiver are
already paired together. However, if you have
multiple fans and remote controls and want to
avoid interference between them, you can "pair"
other transmitters and receivers together by
adjusting the SUR switches, so the same
numbered keys are in the "ON" position
on both (Fig.8a).
Note: The ceiling fan may work abnormally
if there is interference from other remote
controls.
After making the wire connections, the wires should be
spread apart. The white (neutral) conductor from receiver
and outlet box with green (grounding) conductor on one
side; the black (hot) conductor from receiver and outlet
box with the white, black and blue conductor from receiver
and motor on the other side of the outlet box.
The wire connection points should be turned upward and
pushed carefully up into outlet box.
PAGE: 6 / 10
SUR
ON
SUR
ON SUR
Receiver
Hanger Bracket
Antenna
220817

PAGE: 7 / 10
Remove the plastic insert screws and plastic
inserts from the fan motor assembly first.
Align the holes on one of the blades with the
holes on the bottom of fan motor assembly,
then loosely attach the blade using the screws
provided. Repeat this process for other blades.
Once three blades are in position and connected
with blade screws firmly tighten all screws.
Note: Before installing blades to the motor,
please remove the plastic insert screws and
plastic inserts.
Slide the canopy up to ceiling and over the two canopy screws on hanger bracket.
Rotate canopy clockwise, next, while holding the canopy with one hand, slide the
decorative cap over the screws and rotate clockwise until tight.
Note: Adjust the canopy screws as necessary until the canopy and canopy
cover are snug.
Remove three set screws from fan motor assembly first (for later use), then thread
the fan motor assembly wires through connect plate of light kit. Push the connect
plate of light kit upwards then align and engage the connect plate of light kit holes
to fan motor assembly holes. Finally, secure the connect plate of light kit to the fan
motor assembly bottom with previous screws which were removed.
Remove three fix screws from connect plate of light kit first.
Then connect the white (neutral) wire from the light kit to
white (neutral) wire from fan motor assembly with a wire
connector; connect the black (hot) wire from light kit to
blue (hot) wire from fan motor assembly with a wire connector.
Carefully put the wires into the bottom of connect plate of light kit,
then attach the light kit onto the connect plate of light kit with
previous three fix screws.
Attach the glass shade to the light kit by aligning studs
and slots, and turn it clockwise until it is locked in place.
Fig.14 Fig.15
Connect Plate of Light Kit
Fig.17
Fig.16
Turn ON the electric cicuit at the main
fuse or circuit breaker box.
The slide switch on motor assembly sets diredtion of fan rotation.
Select the desired direction of fan rotation. Push the slide switch
down for "Forward" and up for "Reverse".
Note: Wait for fan to stop before revesing the direction of blade rotation.
Fig.11
Canopy Screw
Hanger Bracket
Canopy
Decorative Cap
Fig.13
Fan Motor
Assembly
Blade
Plastic Insert Screw
Plastic Insert
Blade Screw
Set Screw Connect Plate of Light Kit
Fan Motor Assembly
220817

PAGE: 8 / 10
Fig.19
Transmitter
Wall Bracket
Screw
Note: Remote controller can not be used along with a solid-state speed control at the same time.
Install the battery (9V, included) into the transmitter.
* Press "HI" button to turn on the fan at high speed.
* Press "MED" button to turn the fan in medium speed.
* Press "LOW" button to turn the fan in low speed.
* Press "FAN OFF" button to turn off the fan.
* Press "LIGHT ON/OFF" button to turn on or turn off the light.
* Press and hold the "DIMMER" button to dim or brighten lights to the desired level and
release, and the brightness level will be memorized. Turn on the light again, then fan
light will be restored to the brightness-level at which it was dimmed last time.
Note:
1. This remote controller has a memory function setting. The fan will operate at the
same speed and the fan light will stay at the same brightness-level as the last time
the power supply was turned off.
2. Compatible Wall Switch: Menards SKU# 363-5815.
Install the transmitter wall bracket on the wall with two screws
and place transmitter in it carefully.
Fig.18
Fig.20
Fig.21
1
20
220817

PAGE: 9 / 10
Fig.22
Fig.23
Fig.24
220817

PAGE: 10 / 10
220817