PATROLLINE HPS 841 GSM Datasheet

HPS 8 4 1 G S M
U S I N G I N S T R U C T I O N
F R O M 15.07.2010
N E W G E N E R A T I O N C A N -B U S
C a r a l a r m - A n t i t h e f t s y s t e m ,
i n t e g r a t e d G S M a g e r
December 2010.

Operation
Operation
ALARM SYSTEM ARMING
Push the closing button of the default remote control. The activation will be
confirmed by the followings:
•Blinker flashing based on the closing features of the vehicle
•1 bee (if it is rogrammed)
•The LED on the dashboard switches ON
•Activation of electric engine immobilizer (if installed)
•The module out uts switch ON (ultrasonic sensor, hy erfrequence etc.)
•The CDL closes the doors
ALARM SYSTEM DISARMING
Push the o ening button of the default remote control. The deactivation will
be confirmed by the followings:
•2 bee (if it is rogrammed)
•The LED on the dashboard switches OFF
•Deactivation of electric engine immobilizer (if installed)
•The module out uts switch OFF (ultrasonic sensor, hy erfrequence
etc.)
•The CDL o ens the doors
•Blinker flashing based on the o ening features of the vehicle
Automati rearming
If you switched OFF the alarm with the default remote control of the vehicle, but the doors didn’t
o en, within 15 seconds the CDL closes back automaticaly the doors, and in the meantime the alarm
switches ON.
Warning! In those cars, in which there isn’t automatic CDL closing back function, ask the
installer, that program the automatic re-inhibition function of the alarm! If it is
programmed, the automatic re-inhibition function of the alarm will operate, but only the
alarm switches N, the CDL doesn’t close!
December 2010.

Inhibition time, status of alert
After you switched ON the alarm with the default (OEM) remote control, the alarm will stay for 20
seconds into “neutral time” condition, signalled by the fixed light of the LED. The flashing of the LED of
the dashboard will indicate that the system su ervises the vehicle and is ready to signal the alarms.
Alarm
Alarm
In case of attem t to brake in, the system will emit an o tic-acoustic signal (flashing of the blinkers and
sound of the horn or of the siren, if installed, for 30 seconds, re eated.
To sto the alarm without disarming, ress the CLOSING button of the remote control
To sto the alarm and disarming, ress the OPENING button of the remote control.
Pani fa ility
Pani fa ility
After the inhibition time, if you ress the CLOSING button of the remote control, the alarm will trigger
till 30 seconds (bee /acoustic signal). Warning! You have to activate the panic function to
operate it. Ask the hel of the installer to the activation!
Alarm status
Alarm status
If armed alarm is disconnected from its connector, after the reconnection it stays in armed status,
rotected the car further.
Anti hi-ja k fun tion
Anti hi-ja k fun tion
The alarm can immobilize the engine while the engine is ON when somebody hijack the car. This
function is switch OFF defaulty. The switching ON of this function ha ens based on the request of the
client in writing.
To switch ON this function, lease contact with the installer.
Antiagression fun tion
Antiagression fun tion
The alarm can immobilize the engine while the engine is ON when somebody hijack the car together
with its own keys. This function is switch OFF defaulty. The switching ON of this function ha ens
based on the request of the client in writing.
To switch ON this function, lease contact with the installer!
Ex lusion of Siren
Through the ignition key it is ossible to exclude the function of the horn or the siren.
With disarmed alarm (CDL o ened), turn ON and OFF the ignition key for 3 times and, within 30
second, ress the original remote control to close the CDL of the vehicle.
By this time, the central unit will signal the attem t to break in by the flashing of the blinkers only.
December 2010.

Warning! The exclusion of the siren is valid for only one cause of trigger! If you switch OFF the alarm
with the remote control, the system will be restored automatically in the original state, and for the next
switching ON it will react with beep and acoustic signals for every cause
On
Off
1st time
2nd time
3rd time
On
Off
On
Off
(LED off)
IGNITION KEY
control to close the doors
Push the original remote
With CDL open
within 30 seconds
Memory of Alarm
If the central unit records one or more causes of alarm, they are signalled, when disarming, through the
LED. To verify the ty e of alarm, check the number of flashings of the LED with the table below.
N. flashings of the LED CAUSE
1DOORS OPENING (WITH CAN-BUS SIGNALLING)
2DRIVER’ SIDE DOOR OPENING WITH MECHANICAL KEY (WITH CAN-BUS
SIGNALLING)
3BONNET OPENING (WITH CAN-BUS SIGNALLING)
4TRUCK (WITH CAN-BUS SIGNALLING)
5IGNITION PROTECTION
6SHOCK SENSOR
7ULTRASONIC SENSOR
8EXTRA SENSORS OF ALARM (BLUE IRE INPUT)
9EXTRA SENSORS OF ALARM (BLUE/RED IRE INPUT)
10 EXTRA SENSORS OF ALARM (GREEN/BLACK IRE INPUT)
11 TRIGGERING OF DEFAULT ALARM
12 SHORT TRIGGERING OF OPTIONAL SHOCK SENSOR
13 TOTAL TRIGGERING OF OPTIONAL SHOCK SENSOR
December 2010.

Safety fun tion
Door protection Door, trunk and bonnet open sense
Engine block Prevent the start of the motor of the door
Shock sensor Sense the broke of the door’s window
Ignition protection Sense the ignition of the car
Ultrasonic Option! Sense the moving in the passenger compartment
Anti hi-jack Block the engine, if somebody wants to steal the car for ignition key
ON case
Antiagression Block the engine, if somebody wants to steal the car for car starting
with its own key
Ultrasoni / Hyperfrequen e ex lusion
Ultrasoni / Hyperfrequen e ex lusion
This function is necessary, if you want to leave the dogs or cats in the car without the triggering of the
alarm. In the active state of the function, the other senses of the alarm o erate. After locking, during
inhibition time, ush the lock button of the remote control to switch on this function. The alarm signs
the exclusion of the ultrasonic / hy erfrequence sensors with one blinker flashing and 3 bee s signals.
PIN ode
PIN ode
The PIN code is for that the user can switch OFF the alarm, if the remote control or the alarm get
wrong or the battery discharged.
PIN code emergency switch OFF function of the alarm, de endent on alarm rogramming, has 3 ty es
o erating o ortunities, which are the followings:
1. PIN code emergency switch OFF with ignition key (it is the default setting of the alarm).
2. PIN code emergency switch OFF with usage of brake edal/hand brake (this function can be
used after rogramming of the alarm).
3. PIN code emergency switch OFF on ignition key ON, automaticaly (this function can be used
after rogramming of the alarm).
In all boxes of the alarms can be found an envelop, which contains a secret PIN code. nly
the user can open this envelop. All alarms have different PIN code! We suggest for the user
as for the perfect safety to change the original set PIN code for a new, own one. Please
follow the next instructions in the followings chapters.
If you have got any further problem in conncetion of the PIN code, please look for only your
importeur!
December 2010.

Usage of the PIN code is necessary, when the remote control lost, or the battery was flat, or the alarm
went wrong, but the device is switched ON status.
De endent on equi ment of the cars, it can be necessary to change the PIN code emergency switch
OFF o eration, for exam le in that case, if the vehicle is equi ed with “START & GO” system, by
this time we suggest to rogram the alarm for the 2. or 3. emergency switch OFF o erating mode
instead of the default setting of the PIN code emergency switch OFF function!
Only im orter of PATROLLINE and his contracted artners can do the rogramming of the alarm,
because s ecial software and hardware is necessary to it!
1. PIN code emergency switch FF with ignition key (it is the default setting of the alarm)
The code is a 3-figures number (from firm is: 1-2-3) and must be com osed with the ignition key of
the vehicle by following this rocedure:
With armed alarm, o en the driver side door with mechanical key. The alarm starts trigger, by this
time turn ON the ignition key, then turn OFF the ignition key as many time as the first digit of the PIN
code. During turn ON the ignition key the LED switches ON, after the first digit you have to wait to
switch OFF the LED.
After that immediately turn ON and OFF the ignition key as many time as er the second digit.
After the LED switch OFF, turn ON and OFF the ignition key as many time as er the third digit.
If the rocedure was successful, the alarm switches OFF. If the rocedure was unsuccessful, the alarm
stays in inhibition status, and triggers, by this time you have to restart the PIN code emergency switch
OFF rocedure from first digit giving of the PIN code.
2. PIN code emergency switch FF with usage of brake pedal/hand brake (this function can
be used after programming of the alarm)
With armed alarm, o en the driver side door with mechanical key. The alarm starts trigger, by this
time turn ON the ignition key, then ush/draw the brake edal/hand brake as many time as the first
digit of the PIN code (the brake edal/hand brake o erate with CAN-BUS signals not in every car
ty es, therefore they can’t be used for PIN code emergency switch OFF not in every cars!) During
ush/draw of the brake edal/hand brake the LED switches ON, after the first digit, you have to wait
to switch OFF the LED.
December 2010.
pen only by the
USER!!!

After that immediately you have to ush/draw the brake edal/hand brake as many time as the se-
cond digit.
After the LED switching OFF you have to ush/draw the brake edal/hand brake as many time as the
third digit.
If the rocedure was successful, the alarm switches OFF. If the rocedure was unsuccessful, the alarm
stays in inhibition status, and triggers, by this time you have to restart the PIN code emergency switch
OFF rocedure from first digit giving of the PIN code.
3. PIN code emergency switch FF on ignition key N, automaticaly (this function can be
used after programming of the alarm)
With armed alarm, o en the driver side door with mechanical key. The alarm starts trigger, by this
time turn ON the ignition key, then the trans onder identifies the default key, and through the CAN-
BUS network, the alarm switches OFF automaticaly.
WARNING! If the Antitheft / Antiagression function are programmed, before starting of the
procedure, push the secret button used to the Antitheft / Antiagression, and keep it pushed
until the procedure wasn’t finished!
Modifi ation of PIN ode
The modification of the PIN code is necessary if the client want to modify the default PIN code.
Warning! We suggest to the user to modify the default PIN code.
To modify the PIN code, do the following rocedure with the ignition key of the vehicle:
In disarmed alarm case, turn ON and OFF the ignition key as many time as er the first digit of the
PIN code. The LED switches ON when you turn ON the ignition key and after the first digit you have to
wait to switch OFF the LED. After then immediately turn ON and OFF the ignition key as many time as
er the second digit.
After the LED switch OFF, turn ON and OFF the ignition key as many time as er the third digit.
After that the LED flashes some times. Turn ON and OFF the ignition key as many time as er the first
digit of the PIN code while the LED flashes. The LED switches ON when you turn ON the ignition key
and after the first digit you have to wait to switch OFF the LED. After then immediately turn ON and
OFF the ignition key as many time as er the second digit.
After the LED switch OFF, turn ON and OFF the ignition key as many time as er the third digit.
If you succeed, the quick flashing of the LED on the dashboard confirms that the new secret code
has successfully substituted the old one.
December 2010.

If PIN code function of the alarm was rogrammed for brake edal/hand brake mode, you have to do
the above rocedure on same way, only you have to ush/draw the brake edal/hand brake instead of
turn ON/OFF the ignition key!
WARNING! If the Antitheft / Antiagression function are programmed, before starting of the
procedure, push the secret button used to the Antitheft / Antiagression, and keep it pushed
until the procedure wasn’t finished!
Valet fun tion
Valet fun tion
This function is, that during the service of the vehicle, the o erating functions of the alarm are
sus ension.
Usage of the valet function has, inde endently from rogramming of the alarm, 2 ty es o erating
o ortunities, which are the followings:
1. Valet function with anti hi-jack button.
2. Valet function with ignition key (it is the default setting of the alarm).
3. Valet function with usage of brake edal/hand brake (this function can be used after
rogramming of the alarm PIN code emergency switch OFF function)
1. Valet function usage with anti hi-jack button:
Activation of the valet function:
At disarmed alarm, sit into the car. All doors of
the vehicle have to be closed! Turn ON the
ignition key and immediately ush and kee
ushed anti hi-jack button of the alarm, what was
installed into the vehicle. After 10 seconds LED of
the alarm on the dashboard starts trigger and it
flashes till 5 seconds. Till the LED flashes, let off
the anti hi-jack button! By this time the LED
flashes twice slowly, signed arming of the valet
function. If you let off the anti hi-jack button too
early or too late, you have to start the rocedure
from starting!
Deactivation of the valet function:
At disarmed alarm, sit into the car. All doors of
the vehicle have to be closed! Turn ON the
ignition key and immediately ush and kee
ushed anti hi-jack button of the alarm, what
was installed into the vehicle. After 10 seconds
LED of the alarm on the dashboard starts trigger
and it flashes till 5 seconds. Till the LED flashes,
let off the anti hi-jack button! By this time the
LED flashes four times slowly, signed disarming
of the valet function. If you let off the anti hi-
jack button too early or too late, you have to
start the rocedure from starting!
To remind activated status of the valet function, the LED will flash continuously twice if you turn ON the
ignition key.
December 2010.

2. Usage of valet function with ignition key (it is the default setting of the alarm, this
function operates in that case too, if the PIN code emergency switch FF function is program
for 3. operating opportunity, the PIN code emergency switch FF on ignition key N,
automaticaly operation):
Activation of the Valet function:
In disarmed alarm case, turn ON and OFF the
ignition key as any time as er the first digit of
the PIN code. The LED switches ON when you turn
ON the ignition key and after the first digit you
have to wait to switch OFF the LED. After that
immediately turn ON and OFF the ignition key as
many time as er the second digit.
After the LED switch OFF, turn ON and OFF the
ignition key as many time as er the third digit.
The LED flashes some times, signed the switching
ON of the valet function.
Deactivation of the Valet function:
Turn ON and OFF the ignition key as any time as
er the first digit of the PIN code. The LED
switches ON when you turn ON the ignition key
and after the first digit you have to wait to switch
OFF the LED. After that immediately turn ON and
OFF the ignition key as many time as er the
second digit.
After the LED switch OFF, turn ON and OFF the
ignition key as many time as er the third digit.
After that the valet function will be in switched
OFF status.
To remind that the Valet function is active the LED on the dashboard will flash twice at any time one
turns on the ignition key.
3. Usage of valet function with brake pedal/hand brake (this function operates, if the PIN
code emergency switch FF function is program for the 2. operating opportunity, the PIN
code emergency switch FF with usage of brake pedal/hand brake operation):
Activation of the Valet function:
In disarmed alarm case, turn ON the ignition key,
and ush/draw the brake edal/hand brake as
many time as the first digit of the PIN code (the
brake edal/hand brake o erate with CAN-BUS si-
gnals not in every car ty es, therefore they can’t
be used for valet function not in every cars!) Du-
ring ush/draw of the brake edal/hand brake the
LED switches ON, after the first digit, you have to
wait to switch OFF the LED.
After that immediately you have to ush/draw the
brake edal/hand brake as many time as the se-
cond digit.
Deactivation of the Valet function:
Turn ON the ignition key, and ush/draw the
brake edal/hand brake as many time as the first
digit of the PIN code. During ush/draw of the
brake edal/hand brake the LED switches ON, af-
ter the first digit, you have to wait to switch OFF
the LED.
After that immediately you have to ush/draw the
brake edal/hand brake as many time as the se-
cond digit.
After the LED switching OFF you have to
ush/draw the brake edal/hand brake as many
time as the third digit. After that the valet
December 2010.

After the LED switching OFF you have to
ush/draw the brake edal/hand brake as many
time as the third digit.
The LED flashes some times, signed the switching
ON of the valet function.
function will be in switched OFF status.
To remind that the Valet function is active the LED on the dashboard will flash twice at any time one
turns on the ignition key.
WARNING! If the Antitheft / Antiagression function are programmed, before starting of the
procedure, push the secret button used to the Antitheft / Antiagression, and keep it pushed
until the procedure wasn’t finished! (except the „1. Valet function with antitheft button”
mode)!
Operation of GSM PAGER
Operation of GSM PAGER
During using of HPS 841 GSM PAGER, you can ask, get message for your tele hone about the extant
triggerings, switched ON / OFF status of the alarm, o ened status of the vehicle CDL, or door, flat of
the vehicle battery with calling and/or SMS.
Warning signals for triggering
Warning signals for triggering
The system can warn the vehicle owner on 3 ways for triggering, (or the erson, whose tele hone
number is saved in the alarm):
1. The system warns with calling for triggering (maximum 3 clinks, or till 10 seconds). If the
called erson refuses the calling, the warning rocedure breaks, and the arrived calling
hasn’t any cost! The device acquits reaching into aim of the triggering warning with refusing
of the calling, so it doesn’t send SMS message.
2. If the called erson acce ts the calling, the system cuts off the tele hone line, and sends a
warning SMS, which contains the triggering cause too! Warning! In this case the warning
has calling and SMS sending cost!
3. If the called erson doesn’t acce t the calling (he doesn’t lift the receiver during maximum 3
clinks or 10 seconds time), the system cuts off the tele hone calling, and sends a warning
SMS, which contains the triggering cause too! Warning! In this case the warning has calling
and SMS sending cost!
Information about armed or disarmed status of the alarm
Information about armed or disarmed status of the alarm
The system sends notice in SMS about armed or disarmed status of the alarm, if we ask it with the
SMS sent for the alarm. After sending we get re ly SMS immediately, which contains the information
about armed or disarmed status of the alarm.
December 2010.

Warning signal about opening of CDL
Warning signal about opening of CDL
The system sends warning in SMS about o ening of the CDL, if we switch ON this function with sending
of a rogramming SMS in the alarm. If we rogrammed this function, the alarm in all case, when the
CDL o ens, sends SMS. Warning! The system sends SMS, if the CDL, door, doors are o ened with the
default remote control, mechanical key, inside the car with hand, or breaking o en! In all case the
warning has SMS sending cost!
Warning
Warning signal about flat of battery signal about flat of battery
The system sends warning in SMS, if voltage of the vehicle battery decrease under 11V through at least
3 minutes. As the system sends warning SMS in only that time case, which longer than 3 minutes,
therefore it doesn’t send notice about decreased battery voltage at starting of the vehicle! This
functions is rogrammed defaulty.
Programming of GSM PAGER
Programming of GSM PAGER
The HPS 841 GSM PAGER is rogrammable with SMS. Firstly you have to rogram the tele hone
number with SMS, for which you would like to get the calling and SMS warnings.
The following table contains which SMS commands, information asking are sendable for the alarm, and
for them which answers, information arrive:
Warning! In the SMS commands you have to leave always space after the 1234 (or the
modified) password!
FUNCTI N INSTRUCTI N
C NTENT F
SENDED SMS
C NTENT F
ANSWER SMS
N TE
Tele hone number 1 saving,
modification in the alarm
memory.
1234 A1(PHONE
NUMBER)
TELEPHONE NUMBER
IS MEMORIZED
YOU HAVE TO SEND THE PHONE NUMBER WITH THE
INTERNATIONAL PREFIX! AFTER SAVING, THE ALARM WILL
SEND WARNING FOR THESE TELEPHONE NUMBERS.
Tele hone number 2 saving,
modification in the alarm
memory.
1234 A2(PHONE
NUMBER)
TELEPHONE NUMBER
IS MEMORIZED
YOU HAVE TO SEND THE PHONE NUMBER WITH THE
INTERNATIONAL PREFIX! AFTER SAVING, THE ALARM WILL
SEND WARNING FOR THESE TELEPHONE NUMBERS.
Password modification. 1234 W(NEW
PASSWORD)NEW PASSWORD
THE PASSWORD ALWAYS CAN BE 4 CHARACTERS! IF YOU
MODIFY THE PASSWORD, FROM THAT TIME ALWAYS, YOU
HAVE TO USE THE NEW PASSWORD IN THE SMS COMMANDS
INSTEAD OF 1234 DEFAULT PASSWORD!
Request of
armed or disarmed status of
the alarm.
1234 I ALARM ARMED
ALARM DISARMED
YOU GET IN ANSWER SMS, THAT THE
ALARM IS ARMED OR DISARMED STATUS.
December 2010.

Armed of SMS warning
function about the CDL,
or the door(s) o ening.
1234 D1 STATUS INFORMATION ARMED
IN EVERY CASES, IF THE CDL, OR SOME DOORS IS OPENED,
YOU GET AN SMS WITH THE FOLLOWING TEXT: CDL
OPENED.
Disarmed of SMS warning
function about the CDL,
or the door(s) o ening.
1234 D0 STATUS INFORMATION
DISARMED
BY THIS TIME THE SMS WARNING IS DISARMED ABOUT THE
CDL, OR THE DOOR(S) OPENING.
Engine block and
horn / siren activation
YOU CAN ASK THE
NECESSARY CODE FROM THE
INSTALLER AGAINST
WRITTEN DECLARATION
ENGINE BLOCKED THE ENGINE WILL BLOCK IMMEDIATELY AND THE HORN /
SIREN SWITCH ON FOR 30 SEC.
Engine block disable,
horn / siren disarmed
YOU CAN ASK THE
NECESSARY CODE FROM THE
INSTALLER AGAINST
WRITTEN DECLARATION
ENGINE BLOCK DISABLED THE ENGINE BLOCK WILL DISABLED
SMS-s sent by GSM PAGER által
SMS-s sent by GSM PAGER által
The HPS 841 GSM PAGER sends warnings with SMS too. The following table contains, what the warning
SMS contains and it is in which case: The following table contains the English translation.
C NTENT F G TTEN SMS NOTE
Tele hone number 1 is memorized WITH SMS SENDING YOU MODIFIED THE FIRST PHONE NUMBER SAVED IN THE ALARM MEMORY, FOR
WHICH THE SYSTEM SENDS WARNINGS WITH CALLING, WITH SMS.
Tele hone number 2 is memorized WITH SMS SENDING YOU MODIFIED THE SECOND PHONE NUMBER SAVED IN THE ALARM MEMORY, FOR
WHICH THE SYSTEM SENDS WARNINGS WITH CALLING, WITH SMS.
New assword = WITH SMS SENDING YOU MODIFIED THE ALARM PASSWORD, WHAT YOU HAVE TO USE IN THE SMS
COMMANDS.
ALARM by shock THE ALARM TRIGGERS BECAUSE OF SHOCK OR STRONGE VIBRANCY.
ALARM by key THE ALARM TRIGGERS, BECAUSE OPENED THE CAR CENTRAL DOOR LOCKING WITH MECHANICAL KEY.
ALARM by ultrasonic THE ALARM TRIGGERS, BECAUSE THE ULTRASONIC INTERIOR PROTECTION SENSED MOVING.
ALARM by door THE ALARM TRIGGERS, BECAUSE OPENED SOME DOORS OR TRUCK OF THE CAR.
ALARM by bonnet THE ALARM TRIGGERS, BECAUSE OPENED THE BONNET OF THE CAR.
ALARM by aux sensor THE ALARM TRIGGERS, BECAUSE THE CONNECTED ADDITIONAL MODULE (FOR EXAMPLE: LIFTING
SENSOR, RADAR) SENSED TRIGGERING CAUSE.
December 2010.

Low battery THE BATTERY VOLTAGE OF THE VEHICLE FALLED UNDER 11 V FOR TIME MORE THAN 3 MINUTES.
Info enabled WITH SMS SENDING YOU SWITCHED ON THE SMS WARNING FUNCTION ABOUT OPENING OF THE
CENTRAL DOOR LOCKING OR THE DOOR(S).
Info disabled WITH SMS SENDING YOU SWITCHED OFF THE SMS WARNING FUNCTION ABOUT OPENING OF THE
CENTRAL DOOR LOCKING OR THE DOOR(S).
Car o ened
AFTER THAT WITH SMS SENDING YOU SWITCHED ON THE SMS WARNING FUNCTION ABOUT OPENING
OF THE CENTRAL DOOR LOCKING OR THE DOOR(S), THE SYSTEM SENDS THIS MESSAGE FOR EVERY
CENTRAL DOOR LOCKING OR DOOR OPENING.
Engine blocked ENGINE OF THE VEHICLE IS BLOCKED, AND THE HORN / SIREN WILL BE ON FOR 30 SEC. THE
ENGINE BLOCK IS ACTIVE FOR 105 MINUTES, THEN IT AUTOMATICALY DISABLED.
Engine block disabled THE BLOCKED ENGINE AND SIREN TRIGGERING WILL SWITCH OFF / DISABLED.
Alarm maintenan e
Alarm maintenan e
The alarms of our range are based on a very high technology and are characterized by an extreme
reliability. Using some shrewdness it is ossible make them living longer and working better:
VEHICLE WASHING: in case the vehicle has to be washed with some high ressure devices (hydro-jet or
similar), it is necessary to rotect the alarm before starting the washing rocedure. In case of
infiltrations of water caused by using the hydro-jet, the warranty will be automatically annulled.
GENERAL MAINTENANCE: all the re airing o erations to the alarm must be done by PATROL LINE centres;
tam ering by non authorized staff can com romise the reliability of the device and the safety when
the vehicle is going.
De laration of onformity
De laration of onformity
This roduct is in conformity with the:
E/ECE/324
E/ECE/TRANS/505 Regulation No. 116 >> Rev.2/Add.115
European Directive, so it satisfies all the requirements asked about the functionality of the alarm
devices, and for the electromagnetic com atibility.
It is necessary to fill in right the guarantee located in the box in order to use the guarantee of the
device.
December 2010.

The following certification number has to be on the device, that it harmonizes with the conformity.
E24 116R A-000018
Note:
Patrolline Kft
8000 Székesfehérvár, Királysor 32.
Tel/Fax: [phone]
E-mail: [email protected]
Web: www.canbusriaszto.hu, www.patrolline.eu
December 2010.