Pavone Systems KIT MKX 65023 User manual

PAVONESYSTEMS
MOUNTING INSTRUCTIONS
KIT MKX Accessory for Beam and Shearbeam load cells mod. 65023, 65083, 350, BBR, SBR, SB

Page II

Rel ID 19500203
Page 1Page 1
PRECAUTIONS
READ this manual BEFORE operating or servicing the mounting KIT.
FOLLOW these instructions carefully.
SAVE this manual for future use.
CAUTION:
The installation and maintenance of this mounting KIT must be allowed to qualified personnel only.
Pay attention during inspection, testing and adjustment.
Failure to observe these precautions may be dangerous.
DO NOT ALLOW untrained personnel to work, clean, inspect, repair or tamper this KIT.

B
A2
ØD 7 HOLES
A1
A
B1
C1
B
B3
C4
C3
C
C2
A3
B2
Page 2
DIMENSIONS
MODEL CAPACITY kg A A1 A2 A3 B B1 B2 B3 C C1 C2 C3 C4 ØD
MK0-MK1 75÷250 180 150 15 28,4 100 70 100 70 97,5 100,5 19,5 15,5 15 13
MK2 300÷2000 180 150 15 28,4 100 70 100 70 97,5 100,5 19,5 15,5 15 13
MK3-MK4 3000÷5000 250 210 20 41,6 150 110 150 110 136,5 140 29,5 24,5 24,5 18
MK6 5÷500 180 150 15 30 100 70 100 70 97,5 100,5 19,5 13,5 15 13
MK10 7500÷10000 300 260 20 28,3 200 160 200 160 184 190 39,5 39,5 24,5 22
MAXIMUM LOAD IN KG
MODEL CAPACITY kg COMPRESSION TILT LOAD
MK0-MK1 AS 75÷250 10540 6820 2100
MK2 AS 300÷2000 10540 6820 2100
MK3-MK4 AS 3000÷5000 24440 18810 5750
MK6 AS 5÷500 6470 4280 1580
MK10 AS 7500÷10000 38340 27300 11500
MK0-MK1 SS 75÷250 9420 5970 1880
MK2 SS 300÷2000 9420 5970 1880
MK3-MK4 SS 3000÷5000 21840 16460 5130
MK6 SS 5÷500 5780 3750 1410
MK10 SS 7500÷10000 34200 23900 10200

1
2A
3
4
5
6
7
8
1
2B
34
5
6
7
8
Page 3Page 3
DESCRIPTION
The mounting KIT mod. MKX is supplied without the load cell but already assembled, ready to be
mounted or further shipped.
LEGEND
1 Base Plate with 3 through holes for ground fixing
2 Shearbeam load cell
3 Load cells fixing bolts
4 Ball-support accessory
5 Load ball in tempered steel
6 Upper Plate with 4 through holes for structure fixing
7 Locking bolts for transportation
8 Anti-tilt bolts. DO NOT remove

Page 4
MOUNTING INSTRUCTIONS
1. Use the mounting KIT already assembled as drilling template.
Fix the structure to be weighed to the upper plate and fix the base plate to the ground.
2. Make all the mechanical connections and welding. At this point it is possible to fix the load cell
with the ball and its support to the base plate and make the electrical connections. The system is
now ready either to be shipped or started.
3. To start the system remove completely the two bolts in RED.
4. Use an hexagonal wrench to adjust the height of the upper plate (max 3mm). The upper plate
will consequently charge the load cell.
5. Make sure the upper plate is fully parallel to the base plate to obtain a correct weighing.
NOTE: During transportation the load ball is kept in its position and can’t escape its place.

120°
120°
Page 5Page 5
ORIENTATION OF WEIGHT MODULES
3 x 120°
4 on diagonals

PAVONE SISTEMI S.R.L.
Via Tiberio Bianchi, 11/13/15, 20863 Concorezzo (MB)
T039 9162656 F039 9162675 Wen.pavonesistemi.it
Industrial Electronic Weighing Systems since 1963