PAWW WaveCast RX User manual

User Guide
Congratulations on your purchase of the Paww WaveCast RX Bluetooth wireless
receiver! WaveCast RX transforms any home audio system into a
Bluetooth-enabled system which can wireless stream audio from any
Bluetooth-enabled source device, such as your smartphone, tablet, laptop, etc.
Now you can stream music through your favorite audio system, without being
tethered by wires!
1. Product overview
①Multi-function button (MFB) – (Power on / Pairing Mode / Play / Pause /
Power off)
②LED indicator
③3.5 mm audio jack
④Mirco-USB charging Port
2. Package Contents:
A. 1 Amp USB Power Adapter (UL certificated)
B. Aux 3.5mm audio cable
C. Micro USB charging cable
D. User Guide
1.INITIAL SETUP
Please use the diagrams above as reference for the steps below:
1. Connect the included 3.5mm auxiliary cable to the the 3.5mm port on
WaveCast RX (reference 3 of Product Overview).
2. Connect the other end of the 3.5mm auxiliary cable to the audio device’s
3.5mm AUX IN port (please ensure that you connect to the Aux In port and
not the output port marked with a headphone). Turn on your speaker and
set the input source to AUX.

3. Insert the attached power adapter to wall socket.
4. Insert the USB charging cable into the power adapter.
5. Plug the micro-USB end of the charging cable into the WaveCast RX’s
micro-USB charging port (reference 4 of Product Overview)
6. At this point both the auxiliary cable and micro-USB charging cable should
be plugged into the WaveCast. This will automatically put the WaveCast RX
into pairing mode.
7.Pressing and holding the Multifunction button (reference 1 in Product
Overview) for 2 seconds will also switch the device on and put it into pairing
mode. To confirm that the device is in pairing mode, you will hear two
prompts: “power on” and “pairing”.
8.Navigate to Bluetooth settings on your phone or tablet, and search/scan for
new devices. Once WaveCast RX appears, select it and follow the prompts
to complete the pairing process. Once successfully paired, you were hear
the prompted “connected”.
3.POWER OFF
1.Press and hold the Multifunction button for 5-seconds to switch WaveCast
RX off. Your audio system will prompt “power off”.
2.Remove the micro-USB cable from the WaveCast RX to power the unit off.
4.PAIRING WITH TWO DEVICES
1.Pair the first device to WaveCast RX using the steps outlined above.
2.Switch off Bluetooth on the first device. This will place the WaveCast RX
back into pairing mode.
3.Pair the second device to WaveCast RX using the steps outlined above.
4.Switch on Bluetooth on the first device. WaveCast RX should now be
connected to two devices concurrently.
5.RECONNECTING TO A PREVIOUSLY PAIRED DEVICE
1.Whenever the WaveCast RX is powered on, it will automatically reconnect
to the last paired and connected device.
2.To pair the WaveCast RX to another device, press and hold the
Multifunction Button for approximately 3 seconds or until you hear the
prompt “pairing”, then follow the instructions above.
6.FUNCTION DESCRIPTION
Function Operation LED
Power
On
Charge the WaveCast RX via Micro
USB cable
Blue LED Flashes
Rapidly
Power
Off
Unplug the micro-USB cable from
WaveCast RX N/A
Pairing
Press and hold the Multifunction
button for 3 seconds. The device
stays in pairing mode for 10 minutes.
If not paired during that time, device
shuts off.
Blue LED flashes
Rapidly
Play
music
If music is paused, press the
Multifunction button once to start
playing the music.
Blue LED flashes
twice every five
seconds
Pause
music
To pause music, press the
Multifunction button once.
Blue LED flashes
twice every ten
seconds
Standby Connected to a Bluetooth device, but
no audio streaming
Blue LED flashes
once every ten
seconds
7. RESETTING THE WAVECAST RX
If the WaveCast RX is behaving abnormally, it may require a factory reset. Once
the reset is complete, all existing pairing information is lost, and all previously
paired devices will have to be paired again using the steps outlined above.
Note: Please make sure that the WaveCast RX is connected to an audio device
prior to doing the factory reset.
To do a factory reset, press the Multifunction button for approximately six
seconds, or until you hear the prompt “power off” followed by two beeps.
8. PRODUCT SPECIFICATIONS
• Bluetooth Version: V5.0+EDR
• Chipset: QCC3003
• Operating Range: Class 2 - Up to 10 meters
• Supported Profiles: HFP v1.7, A2DP v1.3, AVRCP v1.6
• Supported Decoders: AAC, SBC, MP3
• Multipoint Support: A2DP Connection to Two Devices.
9. WARRANTY
The Paww WaveCast RX Bluetooth receiver ships with a 1-year warranty. If you
do encounter any issues during this time, you can initiate a warranty claim by
contacting us via email on [e-mail] or through the Contact Us
page on our website (https://www.mypaww.com/pages/contact-us).