PDR AWM125-120 User manual

Model
AWM125-120 ARTICULATING WALL MOUNT INSTRUCTIONS
Thank you for purchasing the PDR mount.
To ensure the correct usage, please read and follow the instructions
manual thoroughly. Please store the instructions in a safe place
To ensure customer safety, be sure to decide the installation location so that the strength is sufficient to withstand the weight
display and the wall mount.
Always use at least two persons for all installations.
Fully tighten all of the mounting screws as specified in the installation instructions.
Features
Special techniques are necessary for installation of the panel display mount.
Do not attempt to perform this work by yourself.
Request an installation specialist to install this unit.
Manufacturer assumes absolutely no responsibility for injuries and damages that may occur due to improper installation and handling.
Please remember that if you remove the panel display from the wall later, you will find the screw holes and anchor bolts for t
mounting unit left on the wall. Also note that long use of the panel display may discolor the wall around it due to its heat a
airflow.
1
Fig 1
All PDR mounts and adapters carry a limited lifetime warranty against defects in material and workmanship. We are not liable
for improper installation that results in damage to mounts, adapters or presentation equipment.
To register visit our web site @ www.pdrmounts.com
Mounts by
A division of David Engineering & Mfg. Inc.
for future reference.
of both the panel
he
nd
R
R
R
R
R
R
R
R
R
R
R
Simple to adjust
Adapter plate included
125 lb rated
AWM 125-120 FITS 22” TO 36” DISPLAYS
Rugged heavy gauge metal construction
Tough powder-coated finish
Extends 20.7” from the wall and closes to under 4.6”
Pivots left or right, tilts up 5 deg. and down 15 deg.
3 adjustable height positions
Includes cable management system
Tension bolts to adjust smooth action and eliminate creep

the strength of the wood studs is not sufficient, add reinforcement.
Always confirm the center of the stud is used for the installation.
Avoid installing in locations where the temperature and humidity are excessively high, and where contact with any
not install in locations where there are excessive amounts of dust,
Do not block the ventilation holes. Leave sufficient clearance in regard to the surroundings to avoid blocking the ventilation..
The internal temperature could elevate and possibly result in fire. Install the panel (4") or more away from surroundings.
sloped surfaces. Also, do not install facing upward. The internal temperature could
elevate and possibly result in fire. Injury or damage could also result from falling.
Do not install in locations where there is excessive vibration or impact. Injury and damage could result from the panel display
light. Strong light could result in eye fatigue during usage.
Use the specified bolts and screws in the specified places and tighten firmly. Failure to do this could cause injury if the panel
could result with injury due to the panel display falling.
Always use at least two people to perform the installation work. Injury could result from dropping heavy objects.
be installed must be capable of long-term support of the total load of
so be taken to ensure sufficient strength to
vibration and other external forces.
panel display to fall and cause injury.
MAXIMUM WEIGHT= 125 Lbs. ( 57 Kg.)
C a u t i o n : I n s t a l l a t i o n o f u n i t i s t o b e c a r r i e d o u t b y q u a l i f i e d t e c h n i c i a n s o n l y . I n s t a l l i n a n a p p r o p r i a t e
l o c a t i o n b y c h e c k i n g t h e w a l l s t r u c t u r e a n d d u r a b i l i t y f o r s a f e t y a n d a c c i d e n t p r e v e n t i o n .
INSTALLATION LOCATION
INSTALLATION ON A WOODEN WALL
Always install so that the load is supported by a wood stud. If
Do not install on decorative posts or plaster board.
water is possible. These can result in fire or electric shock.
Do not install close to an air conditioner intake or outlet. Do
oily smoke or tobacco smoke. Fire could result.
.
Install only on a vertical surface. Avoid
falling.
Do not install where there is direct sunlight or other strong
display falls.
Do not alter any of the parts. Do not use broken parts. This
The wall where the wall mount is to
the panel display and wall mount. Measures should al
withstand the force of earthquakes,
Note: Incorrect installation can cause the
CAUTION
WARNING
WARNING
2
Total load ( panel display + mount )
Rev 100708

PART NUMBER
PH-E-25-50-ST
1/4-20X½" SELF TAPPING
PAN HEAD SCREW
4 REQUIRED
SUPPLIED HARDWARE
3
PART NUMBER
CT-E-37-37-00
PLASTIC CABLE MANAGEMENT
CABLE TIE HOLDER
4 REQUIRED
5/16 X 2 1/2 LAG BOLT
3 REQUIRED
LB-E-31-25-00
5/16 X 7/8 USS STEEL
FLAT WASHER
3 REQUIRED
FW-E-31-06-00
LINEAR (RECTANGULAR)
MULTI WASHER
4 REQUIRED
PDM-0044
M8 X 40 PAN HEAD
PHILLIPS MACHINE SCREW
4 REQUIRED
PH-M-08-40-00
M6 X 40 PAN HEAD
PHILLIPS MACHINE SCREW
4 REQUIRED
PH-M-06-40-00
M5 X 40 PAN HEAD
PHILLIPS MACHINE SCREW
4 REQUIRED
PH-M-05-40-00
M8 X 16 PAN HEAD
PHILLIPS MACHINE SCREW
4 REQUIRED
PH-M-08-16-00
M5 X 16 PAN HEAD
PHILLIPS MACHINE SCREW
4 REQUIRED
PH-M-05-16-00
M6 X 16 PAN HEAD
PHILLIPS MACHINE SCREW
4 REQUIRED
PH-M-06-16-00
.32 ID X .75 OD X 1.00 LONG
PLASTIC SPACER
4 REQUIRED
SP-E-32-10-01
M4 STEEL FLAT WASHER
4 REQUIRED
FW-M-04-09-00
PH-M-04-16-00
M4 X 16 PAN HEAD
PHILLIPS MACHINE SCREW
4 REQUIRED
NYLON ZIP TIE
ZT-E-00-50-00
4 REQUIRED
LOCKING PLATE
2 REQUIRED
PDM-0071
PH-E-25-15-00
1/4-20 X 1 1/2 PAN HEAD
PHILIPS MACHINE SCREW
2 REQUIRED
1
4
7
10
12
15
13 14
16
11
8
5
23
6
9
17

4
DRAWING SPECIFICATIONS
Model AWM125-120
Single stud articulating wall mount
5.39
3.07
4°
24.00
14.00
4.00
8.05
C
L
4.67
20.7
15 DEG
5 DEG

1. FASTEN MOUNT TO THE WALL
Fig 2
Fig 3
2. ATTACH THE DISPLAY BRACKET TO THE DISPLAY
Determine the exact mounting location of the wall mount prior to the installation, considering the swing of the articulating arm.
The AWM125-120 mount must be secured to the CENTER of the wall stud capable of at least (4) times the weight of the display and mount.
The height of the AWM125-120 should be mounted at the same horizontal center line as the desired display center line (viewing center line).
1:Position the AWM125-120 mount to the desired position. Mark and Pre drill the top and bottom holes with a 3/16” (5mm) hole . SEE FIG 2
2: Insert the lag bolt and washer (item 11 and 12) into the top hole and secure to the AWM125-120 mount.
3: Next insert the second lag bolt and washer into the slotted bottom hole. Position with a level tighten the bottom bolt.
4:Fully extend the arm and swing the mount from left to right . Check that the mount is level in both positions. If necessary loosen the bottom bolt and set to a level
position and re tighten the bolt.
5:Pre drill and Install the center lag bolt and tighten. SEE Fig 2
AWM125-120
(item 11 and 12)
1: Lay the display face down on a padded surface.
2: Using the hardware supplied ( see page 3) attach the display bracket to the display. SEE FIG 3
3: Check the depth of the mounting holes to assure you are using the proper length screws supplied .
4: Make note to attach the top of the display bracket to the top of the display.
5: Spacers supplied (1,3,4,7), may be necessary for use, to avoid obstructions on the back surface of the display.
6: Make sure to tighten all fasteners before mounting on the AWM125-120 arm. Care should be taken to not over tighten bolts into the display.
SEE FIG 3
and longer screws
5
WOOD STUDS
(std construction 2 x 4
studs and 1/2” wallboard)
VIEWING
HORIZONTAL
CENTER LINE
FLOOR LINE
Adjustment for level
lag bolts
NOTE: Do not over tighten the bracket mounting screws as damage to the display internal mounting threads could occur.
Mounting hardware 1,2,3,4,5,6,7,8,9
Linear multi washer (15)
Panel display bottom edge
Display bracket
Optional plastic spacers ( 3 )
4°
C
L
DISPLAY CENTER LINE

3. Mounting the display onto the AWM125-120 Articulating arm
3. Final adjustment and cable management
SCREW LOCK TAB
NYLON ZIP TIE
6
Fig 4 Fig 5
Fig 6
1: With the display brackets attached to the display, lift and place the brackets on to the in either the top middle or bottom slots. SEE FIG 4
2: Center the display from left to right on the mounting plate.
3: Screw the 1/4-20 screw (10) into the locking plate (13)
4: Place the locking tab assembly into the slots on the display bracket, and tighten the 1/4-20 screw (10) on each locking tab assembly. SEE FIG 5
mounting plate
Adjust by tightening the tension bolts to suit the desired freedom of movement See fig 6
1: Lift the tie holder(16) on the lock tab to allow access the bolt to adjust the tension on the arm center. Replace the tie holder (16) after adjustment.
3: Two other tension bolts can be tightened or loosened to suit. SEE FIG 6
2: Adjust the tilt by loosening the Tri knob on the side of the AWM125-120 and adjust back or forward for best viewing angle. See fig 6
3: Place the plastic tie holders (16) in the desired holes, and using zip ties (14) attach the cables.
4: Make sure you articulate the mount from side to side looking for any pinching of the cables.
MOUNTING PLATE
DISPLAY BRACKETS
LOCKING TAB ASSEMBLY 1/4-20 screw
large view
TENSION BOLTS
CABLE
TENSION ADJUSTMENT BOLT
TRI KNOB