peerless-AV DS-LEDIER Series User manual

12020-07-01 #:146-9053-3 (2021-01-06)
DS-LEDIER Series
*Actual conguration may vary
ENG Installation video for reference only.
Read and follow instruction manual for full installation.

22020-07-01 #:146-9053-3 (2021-01-06)
Wear anti-static gloves.
ENG
Symbols
ENG
WARNING
ENG
x3
Screws must get at
least three full turns

ENG
Do not overtighten screws.
ENG
ENG - This product is designed to be installed on plywood walls. Hardware is included for plywood installation.

walls. Before installing make sure the supporting surface will support the combined load of the equipment and
hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail.
Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift
and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to

call customer care at 1-800-865-2112.
WARNING

32020-07-01 #:146-9053-3 (2021-01-06)
Tools Needed for Assembly.
ENG
5/32"
(4mm)
3/8"
(10mm)
2.5mm
1
2
ENG To properly tighten screws: Tighten until screw

turn. Do not overtighten screws.
4
+1/2
3

42020-07-01 #:146-9053-3 (2021-01-06)
NM
M5 x 5mm
set screw
#14 x 1.75"
wood screw
A B C
left column right column inside column
Parts List
Description
Aleft column
Bright column
Cinside column
Dvertical spacer
Ehorizontal spacer
Ftop left horizontal asy
Gtop right horizontal asy
Hbottom left horizontal asy
Ibottom right horizontal asy
Jextrusion connector
Kwall plate shim
LM5 x 8mm
MM5 x 5mm set screw
N#14 x 1.75" wood screw
O3mm allen wrench two-tip T-handle
L
M5 x 8mm
K
wall plate
shim
E
horizontal
spacer
J
extrusion
connector
D
vertical spacer
3mm allen wrench
two-tip T-handle
O

Refer to parts list included with your model.
ENG

52020-07-01 #:146-9053-3 (2021-01-06)
F
H
I
G
top left
horizontal asy
bottom left
horizontal asy
bottom right
horizontal asy
top right
horizontal asy

62020-07-01 #:146-9053-3 (2021-01-06)
1-1


ENG
Remove and save hardware.
ENG
F
G
1-2
Use extrusion connectors to connect top horizontal
extrusions.
ENG
J (4) M (8)
O
2.5mm
G
F

72020-07-01 #:146-9053-3 (2021-01-06)
2-1
Optional: If connecting two bottom horizontal

ENG
Remove and save hardware.
ENG
I
H
1-3
Replace one hook-on bracket in between connected
extrusions.
ENG
Use saved hardware.
ENG
G
F
O
O

82020-07-01 #:146-9053-3 (2021-01-06)
I
I
H
H
2-2
Use extrusion connectors to connect bottom
horizontal extrusions.
ENG
M (6)
J (3)
2-3
Replace one hook-on bracket in between connected
extrusions.
ENG
Use saved hardware.
ENG
2.5mm
O

92020-07-01 #:146-9053-3 (2021-01-06)
This page intentionally left blank.
ENG

10 2020-07-01 #:146-9053-3 (2021-01-06)
3


may be covered by gypsum board (drywall) up to 5/8" thick.
WARNING
3-1
ENG 

(+/- .50") across the height of the video wall and straight (+/- .50") across the width of the video wall.
3-2
Use a laser level to keep mounting holes
level.
ENG
2.75"
(70mm)
display tile
7/8"(22mm) minimum
for mounting clearance

11 2020-07-01 #:146-9053-3 (2021-01-06)
3-3
Level top horizontal extrusion and mark
mounting holes on plywood (must be

ENG
G
F

12 2020-07-01 #:146-9053-3 (2021-01-06)
3-4
Drill mounting holes into supporting surface
(1.75" (44mm) minimum depth required).
ENG
5/32"
(4mm)
1.75"
(44mm)
5/32"
(4mm)
3-5
Level extrusion. Install using wood screws
provided.
ENG
3/8"
(10mm)
Maximum 80 in. • lb (9 N.M.).
ENG
N
G
F

13 2020-07-01 #:146-9053-3 (2021-01-06)
3-6

horizontal extrusion.
ENG
3/8"
(10mm)

ENG
D
N
F
D
N

14 2020-07-01 #:146-9053-3 (2021-01-06)
3-7
Use third vertical spacer to align bottom

then mark mounting holes on plywood (must be

ENG
D

ENG
D
I
I

15 2020-07-01 #:146-9053-3 (2021-01-06)
3-9
Use third vertical spacer to align bottom


provided.
ENG
3/8"
(10mm)
Maximum 80 in. • lb (9 N.M.).
ENG
3-8
Drill mounting holes into supporting surface
(1.75" (44mm) minimum depth required).
ENG
5/32"
(4mm)
1.75"
(44mm)
5/32"
(4mm)
I
ND

16 2020-07-01 #:146-9053-3 (2021-01-06)
3-10
Remove vertical spacer.
ENG
3/8"
(10mm)
D
N

17 2020-07-01 #:146-9053-3 (2021-01-06)
4-1
Hook on and secure outer vertical columns.
"L" and "R" markings designate left and right
column.
ENG
A
B
L
Tighten hardware.
ENG
O

18 2020-07-01 #:146-9053-3 (2021-01-06)
4-2
Hook on and secure all inside vertical
columns.
ENG
C
Tighten hardware.
ENG
L
O

19 2020-07-01 #:146-9053-3 (2021-01-06)
5-1
Loosen hardware on vertical columns.
ENG O

20 2020-07-01 #:146-9053-3 (2021-01-06)
5-2
Tighten.
ENG
Tighten.
ENG

hardware. Tighten hardware on four corner wall
plates.
ENG O