peerless-AV DS-LEDIF Series User manual

12018-03-14 #:146-9020-9 (2020-11-18)
DS-LEDIF Series
For Samsung IF015H, IF020H, IF025H
*Actual conguration may vary
ENG Installation video for reference only.
Read and follow instruction manual for full installation.

22018-03-14 #:146-9020-9 (2020-11-18)
Symbols
ENG
WARNING
ENG
Do not overtighten screws.
ENG
Tools Needed for Assembly.
ENG
5/32"
(4mm)
3/8"
(10mm)
#
Skip to step.
ENG
Wear anti-static gloves.
ENG
1
2
ENG To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
4
+1/2
3
ENG - This product is designed to be installed on plywood walls. Hardware is included for plywood installation.

walls. Before installing make sure the supporting surface will support the combined load of the equipment and
hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail.
Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift
and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to

call customer care at 1-800-865-2112.
WARNING
2.5mm

32018-03-14 #:146-9020-9 (2020-11-18)
Parts List
Description
Aleft column
Bright column
Cinside vertical column
Dtop horizontal asy
Ebottom horizontal asy
Ftop vertical spacer
Ghorizontal spacer
HM5 x 8mm socket screw
I#14 x 1.75" wood screw
JM5 square nut (spare)
K3mm allen wrench two-tip T-handle
Lwall plate shim
Mconnector plate
NM5 x 5mm set screw
Obottom vertical spacer
A
B
C
left column
right column
inside vertical column
D
E
top horizontal assembly
bottom horizontal assembly
Parts (Before beginning, make sure you have all parts shown below).
Refer to parts list included with your model.
ENG

42018-03-14 #:146-9020-9 (2020-11-18)
N
I
H
J
M5 x 5mm
set screw
#14 x 1.75" wood screw
M5 x 8mm
M5 square nut
O
L
FG
bottom vertical
spacer
wall plate
shim
top vertical
spacer horizontal
spacer
M
connector
plate
K
3mm allen wrench
two-tip T-handle

52018-03-14 #:146-9020-9 (2020-11-18)
1

62018-03-14 #:146-9020-9 (2020-11-18)
2-1
Optional: If connecting two top horizontal extrusions,

ENG
Remove and save hardware.
ENG
D
D
2-2
Use extrusion connectors to connect top horizontal
extrusions.
ENG
M (4) N (8)
D
D
K
2.5mm

72018-03-14 #:146-9020-9 (2020-11-18)
2-4
Optional: If connecting two bottom horizontal

ENG
Remove and save hardware.
ENG
E
E
2-3
Replace one hook-on bracket in between connected
extrusions.
ENG
Use saved hardware.
ENG
D
K
D
K

82018-03-14 #:146-9020-9 (2020-11-18)
2-5
Use extrusion connectors to connect bottom
horizontal extrusions.
ENG
N (6)
M (3)
E
E
E
E
2-6
Replace one hook-on bracket in between connected
extrusions.
ENG
Use saved hardware.
ENG
K
2.5mm

92018-03-14 #:146-9020-9 (2020-11-18)
3
ENG - When installing Peerless wall mounts on a wood stud wall covered with plywood, verify that the wood
studs are a minimum of 2" x 4" nominal size and plywood is a minimum Grade BC, 1/2" (13 mm) thick. Plywood
may be covered by gypsum board (drywall) up to 5/8" thick.
WARNING
3-1
ENG When installing more than one display to a wood stud wall reinforced with plywood (minimum Grade BC, 1/2"
thick) that may be covered in gypsum board (drywall) up to 5/8" thick, the mounting surface must be plumb
(+/- .25”) across the height of the video wall and straight (+/- .25”) across the width of the video wall.

10 2018-03-14 #:146-9020-9 (2020-11-18)
3-2
Use a laser level to keep mounting holes
level.
ENG
2.24"
(57mm)
display tile
7/8"(22mm) minimum
for mounting clearance

11 2018-03-14 #:146-9020-9 (2020-11-18)
3-3
D
Level top horizontal extrusion and mark
mounting holes on plywood (must be
minimum Grade BC, 1/2" (13mm) thick.)
ENG

12 2018-03-14 #:146-9020-9 (2020-11-18)
3-5
Level extrusion. Install using wood screws
provided.
ENG
3/8"
(10mm)
Maximum 80 in. • lb (9 N.M.).
ENG
D
I
3-4
Drill mounting holes into supporting surface
(1.75" (44mm) minimum depth required).
ENG
5/32"
(4mm)
1.75"
(44mm)
5/32"
(4mm)

13 2018-03-14 #:146-9020-9 (2020-11-18)
3-6

horizontal extrusion.
ENG
3/8"
(10mm)

ENG
I
F
F
F
D

14 2018-03-14 #:146-9020-9 (2020-11-18)
3-7
Use third vertical spacer to align bottom

then mark mounting holes on plywood (must be
minimum Grade BC, 1/2" (13mm) thick.)
ENG
E
F

ENG
F
E

15 2018-03-14 #:146-9020-9 (2020-11-18)
3-9
Use third vertical spacer to align bottom

spacer, then install using wood screws
provided.
ENG
3/8"
(10mm)
Maximum 80 in. • lb (9 N.M.).
ENG E
I
3-8
Drill mounting holes into supporting surface
(1.75" (44mm) minimum depth required).
ENG
5/32"
(4mm)
1.75"
(44mm)
5/32"
(4mm)

16 2018-03-14 #:146-9020-9 (2020-11-18)
4
If your video wall consists of more than four rows, proceed to step 4-1, if not proceed to step 5.
ENG
5
4-1

17 2018-03-14 #:146-9020-9 (2020-11-18)
4-1


ENG
3/8"
(10mm)

ENG
I
I
O
E
O
O
E

18 2018-03-14 #:146-9020-9 (2020-11-18)
4-2
Use third vertical spacer to align bottom

then mark mounting holes on plywood (must be
minimum Grade BC, 1/2" (13mm) thick.)
ENG

ENG
O
E
E
O

19 2018-03-14 #:146-9020-9 (2020-11-18)
4-4
Use third vertical spacer to align bottom

spacer, then install using wood screws
provided.
ENG
3/8"
(10mm)
Maximum 80 in. • lb (9 N.M.).
ENG
I
4-3
Drill mounting holes into supporting surface
(1.75" (44mm) minimum depth required).
ENG
5/32"
(4mm)
1.75"
(44mm)
5/32"
(4mm)

20 2018-03-14 #:146-9020-9 (2020-11-18)
5
Remove vertical spacers.
ENG
3/8"
(10mm)
F
O