PEERLESS Mobile Videowall Trolley PDVWM 2x2 46 55 L Guide

1 of 10 ISSUED: 03-08-11 SHEET #: 125-9195-5 09-20-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
Model: DS-VWC560
Installation and Assembly: 2 x 2 Cart
Maximum Load Capacity 500 Ibs (227 kg)
MAX

2 of 10 ISSUED: 03-08-11 SHEET #: 125-9195-5 09-20-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
BA
F
E
D
C
G
J
IH
KL M
N O
PQ
PARTS LIST
Description Qty. Part #
A
vertical support 2 145-1389
Badapter brackets 8 145-1711
Chorizontal support 3 124-1852
Dhorizontal rail 2 145-1238
E5" caster 4 600-0026
F1/4" flat washer 56 540-9440
GM8 x 25 mm phillips screw 16 520-1031
H5/16 flat washer 16 540-9406
I5/16 split washer 16 540-9405
J1/4-20 x 3.5" hex head screw 56 520-1656
K1/4-20 nylock nut 56 530-9413
L.38 OD x .06 LG nylon washer 16 590-2233
M18" mesh sleeve 4 600-1014
NM8 x 16 mm phillips screw 16 520-9257
OM6 x 12 mm phillips screw 16 520-1128
P4 mm allen wrench 4 560-9646
Qcable tie 8 560-9711
Rtube cap 2 590-1289
SM5 x 10 mm socket pin screw (not used) 8 520-1164
T#14 fender washer (not used) 16 540-1008
Ufront bottom cover 1 145-1364
V
back bottom cover 1 145-1363
Wcomponent shelf 1 145-1361
X
side cover 2 145-1362
Y
decorative screw 12 520-2326
Zspacer 4 590-1136
A
A
front top cover 1 145-1388
BB back top cover 1 145-1368
CC self-drilling phillips screw 3 520-1320

3 of 10 ISSUED: 03-08-11 SHEET #: 125-9195-5 09-20-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
RST
UVW
Z
XY
AA BB CC

4 of 10 ISSUED: 03-08-11 SHEET #: 125-9195-5 09-20-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
Assembling Cart
1Attach two horizontal supports (C) to vertical support (A) using eight 1/4-20 x 3.5" hex head screws (J),
1/4" SAE washers (F) and 1/4-20 nylock nuts (K).
2Attach horizontal supports (C) to second
vertical support (A) using eight 1/4-20 x 3.5" hex
head screws (J), 1/4" SAE washers (F) and 1/4-20
nylock nuts (K).
3Attach horizontal support (C) to vertical supports (A)
using eight 1/4-20 x 3.5" hex head screws (J),
1/4" SAE washers (F) and 1/4-20 nylock nuts (K).
A
C
J
F
K
A
C
JFK
A
C
J
F
K
A

5 of 10 ISSUED: 03-08-11 SHEET #: 125-9195-5 09-20-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
4Attach four swivel casters (E) to vertical supports (A) using sixteen M8 x 25 mm pan phillips screws (G),
split washers (I) and 5/16" SAE at washers (H).
G
I
H
A
E
X
X = HEIGHT OF DISPLAY
A
D
DETAIL 1
DISPLAY HEIGHT
DISTANCE
EQUALS
DISPLAY
HEIGHT
1. Locate the position of the lower horizontal rail (D) and attach to vertical supports (A).
2. Use display height to determine location of upper horizontal rail (D),
NOTE: Lowest horizontal rail (D) position shown in detail 1.
NOTE: Horizontal rails (D) must be secured using sixteen 1/4-20 x 3.5" hex head screws (J).
Determine position of horizontal rails (D) using the formula below.
5
UPPER HORIZONTAL RAIL
LOWER HORIZONTAL RAIL

6 of 10 ISSUED: 03-08-11 SHEET #: 125-9195-5 09-20-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
6Attach horizontal rails (D) onto vertical supports (A) using sixteen 1/4-20 x 3.5" hex head screws (J), 1/4" SAE
washers (H) and 1/4-20 nylock nuts (K) as shown in detail 1. Make sure that horizontal rails (D) are level then
tighten all 1/4-20 x 3.5" hex head screws (J). Place two tube caps (R) into tops of vertical supports (A)
as shown in detail 2. NOTE: horizontal rails (D) must be secured using sixteen 1/4-20 x 3.5” hex head screws (J).
AFK
J
D
D
A
J
J
DETAIL 2
R
CABLE MANAGEMENT
7Run display cables though top and bottom openings
in vertical supports (A) as shown.
NOTE: Display cables can be covered using
18" mesh sleeve (M) before securing.
Display cables can be secured to horizontal rails (D)
using eight cable ties (Q) as needed through slots in
horizontal rails (D).
Q
DISPLAY CABLES
M
D
BOTTOM
OPENING
TOP
OPENING
A
D
SLOT

7 of 10 ISSUED: 03-08-11 SHEET #: 125-9195-5 09-20-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
8Attach adapter brackets (B) to back of display using four M6 x 12 mm phillips screws (O) with nylon shoulder
washer (L), or four M8 x 15 mm phillips screws (N) as shown below.
Adapter Bracket Mounting Patterns
Adapter Bracket Placement Detail
9Use detail 3 to gure adapter bracket (B) placement.
400 mm
300 mm
200 mm
200 mm MIN
600 mm MAX
43.65"
(1109 mm)
68.25"
(1733 mm)
MAX
MIN
33.50"
(850 mm)
MIN
47.50"
(1206 mm)
MAX
DISPLAYS NOT SHOWN FOR CLARITY
DETAIL 3
MAX HOLE
PATTERN
MIN HOLE
PATTERN
MIN HOLE PATTERN
MAX HOLE PATTERN
B
O or N
L
PLP PLATE

8 of 10 ISSUED: 03-08-11 SHEET #: 125-9195-5 09-20-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
10 Hook display and adapter brackets (B) onto horizontal rail (D) as shown below.
NOTE: Hang displays in sequenced order.
NOTE: Once display is located in desired position, tighten security screws as shown in detail 4.
11 Fasten component shelf (W) onto horizontal support (C) using three self-drilling phillips screws (CC)
as shown below.
W
CC
Attaching Component Shelf (Optional)
1
2
3
4
D
B

9 of 10 ISSUED: 03-08-11 SHEET #: 125-9195-5 09-20-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
Use legend below to determine position of display.
NOTE: Each knob can be adjusted independently for ne tuning angle adjustments.
12
Turn knobs CLOCKWISE to raise display height. Turn knobs CLOCKWISE to push out display.
Turn knobs COUNTER-CLOCKWISE to lower display height. Turn knob COUNTER-CLOCKWISE to pull in display.
Adapter Bracket Adjustment
UP DOWN IN OUT
KNOB
KNOB

10 of 10 ISSUED: 03-08-11 SHEET #: 125-9195-5 09-20-12
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112.
TILT FORWARD
NOTE: Position bottom front and back covers rst
Position front bottom cover (U). Secure covers in place using four decorative screws (Y) as shown below.
Position back bottom cover (V). Secure covers in place using four decorative screws (Y) as shown below.
Position front top cover (AA). Secure covers in place using four decorative screws (Y) as shown below.
Position back top cover (BB). Secure covers in place using four decorative screws (Y) as shown below.
Optional: Front top cover (AA), and back top cover (BB) can be interchanged.
13
Attaching Covers
FRONT BACK
SIDE
Z
X
Y
Y
X
Attach two retaining spacers (Z), and decorative screws (Y) to side cover (X) as shown in detail 5.
Attach side covers to vertical supports (A).
U
V
AA BB
DETAIL 5