Pegasus M932 Series User manual

M900

M932 Series: 
M952 Series: 
INSTRUCTIONS
M932 Series: Safety stitch machine
M952 Series:Overedgers
BEDIENUNGSANLEITUNG
M932er Baureihe: Sicherheitsnaht-maschinen
M952er Baureihe: Überwendlichnähmaschinen
INSTRUCTIONS DE SERVICE
Série M932: Machines à point de sécurité
Série M952: Surjeteuses-raseuses ultra-rapides
INSTRUCCIONES PARA EL MANEJO
Serie M932: Maquinas de puntada de sequridad
Serie M952: sobreorilladoras
使用说明书
M932 系列 : 安全缝缝纫机
M952 系列 : 包缝缝纫机


  








INTRODUCTION
Thank you very much for purchasing Pegasus M900
Series machine.
This instruction manual describes daily routine
maintenance and safety precautions to keep the machine
in the best possible conditions.
Please study this manual very carefully before operating
the machine.
BEDIENUNGSANLEITUNG
Wir beglückwünschen Sie zum Kauf lhrer Pegasus-
Maschine der Serie M900.
Diese Betriebsanleitung beschreibt die täglichen
Wartungsarbeiten und die Sicherheitsregeln, die
unbedingt zu befolgen sind, um die Bedienungsperson
und die Maschine vor Schaden zu bewahren.
Bitte lesen Sie diese Betriebsanleitung sorgfältig durch,
bevor Sie die Maschine in Betrieb nehmen.

INSTRUCTIONS DE SERVICE
Toutes nos félicitations pour l'acquisition d'une machine
Pegasus de la série M900.
Les présentes instructions décrivent les opérations
d'entretien quotidiennes et les normes de sécurité à
observer impérativement de manière à mettre l'opératrice
et la machine à l'abri de tous dommages.
C'est pourquoi nous vous prions de lire attentivement
les présentes instructions de service avant de mettre la
machine en marche.
INSTRUCCIONES PARA EL MANEJO
Le felicitamos por la compra de su máquina Pegasus de
la serie M900.
En este manual de instrucciones de servicio se describen
los trabajos de mantenimiento diarios y las normas de
seguridad, que deberán cumplirse estrictamente, para
de esa forma evitar daños en la máquina y lesiones de la
persona que atienda la misma.
Antes de poner la máquina en marcha, le rogamos
estudie detenidamente estas instrucciones de servicio.
使用说明书
为您购买飞马牌 M900 系列缝纫机，我们表示衷心的感
谢!
在使用缝纫机之前，请认真阅读此说明书。愿您自始
至终爱护并使用敝公司的产品。
另外，为使您的缝纫机高效率的使用，此说明书登载
了有关日常中检查与安全的注意事项。
在平时，除了对缝纫机进行检查之外，也请您多加注
意自身的安全 , 做到安全使用。这是我们的心愿。

CONTENTS
目次
Copyright ..................................1
Directives...................................1
1.Introduction ...............................2
2.Indications of dangers, warnings and cautions ...3
3.Safety precautions ..........................5
4.Notes for each procedure ....................7
5.Location of warning labels and safety devices ...13
6.Protectors for safety........................14
Schematic diagram of the sewing machine table ..16
Sewing machine installation ...................17
Operating direction of the machine pulley ........17
Placing the chain for the presser foot lift .........17
Lubrication ................................18
Silicone oil for H.R. device ....................19
Threading .................................20
Replacing the needle ........................21
Adjusting the thread tension...................21
Opening/closing the presser bar ...............22
Adjusting the presser foot pressure .............22
Adjusting the differential feed ratio..............23
Adjusting the stitch length ....................23
Replacing the upper knife.....................24
Replacing the lower knife .....................24
Adjusting overedge width.....................25
Sharpening the knives .......................25
Cleaning the machine........................26
Oil replacement.............................26
To drain the oil..............................26
Changing the fulcrum on the presser foot ........28
Positioning and adjusting the needle thread take-up ....29
Positioning the thread guides / Adjusting the amount of
thread to be supplied from the needle thread take-up ...29
M932 Positioning the thread guides ............30
M952 Positioning the thread guides ............31
Positioning the double chainstitch looper thread take-up and
thread guides / Adjusting the amount of thread to be supplied
from the double chainstitch looper thread take-up .......32
Positioning the looper thread take-ups and the thread guide /
Adjusting the amount of the looper thread supply ..........33
Adjustment dimensions ......................34
Comparison table of equivalent sizes
Standard needle ............................35
Subclass specifications ......................36


 
 
 
 
 
  

 
 


  
...............................





 










M932  .....................
M952  .....................
 








INHALT TABLE DES
MATIERÈS
Copyright .................................39
Directives..................................39
1.Introduction ..............................40
2.Avertissements et consignes.................41
3.Consignes de sécurité......................43
4.Remarques sur chaque opération.............45
5.Position des plaques d’avertissement et
dispositifs de sécurité sur la machine ...........51
6.Dispositifs de sécurité ......................52
Schéma du plateau de la machine..............54
Installation de la machine à coudre .............55
Sens de rotation du volant ....................55
Accrocher la chaîne du relève-pied .............55
Lubrification................................56
Huile silicone pour dispositif HR................57
Enfilage ...................................58
Changement d’aiguille .......................59
Réglage de la tension du fil d’aiguille............59
Escamoter/rabattre la barre presse-tissu .........60
Réglage de la pression du pied presseur ........60
Réglage du rapport du différentiel ..............61
Réglage de la longueur de point ...............61
Remplacement du couteau supérieur ...........62
Remplacement du couteau inférieur ............62
Réglage de la largeur de couture...............63
Affûtage des couteaux .......................63
Nettoyage de la machine .....................64
Changement d’huile .........................64
Evacuation de l’huile.........................64
Remplacement de l’appui du levier du bras du pied
presseur ..................................66
Positionnement et réglage du releveur de fil.......67
Positionnement des guide-fil Réglage du débit
de fil du releveur de fil d’aiguille ................67
M932 Positionnement des guide-fil .............68
M952 Positionnement des guide-fil .............69
Positionnement du releveur de fil de boucleur point de chaînette
et des guide-fil Réglage du débit de fil du releveur de fil de
boucleur point de chaînette ........................70
Positionnement du releveur de fil de boucleur et des guide-fil de
boucleur Réglage du débit de fil du releveur de fil de boucleur . 71
Tableau de réglage ..........................72
Tableau de comparaison des aiguilles/
Aiguille standard ............................73
Caractéristiques techniques des sous-classes ....74
Copyright .................................39
Richtlinien .................................39
1.Einführung ...............................40
2.Gefahren-, Warn- und Vorsichtshinweise .......41
3.Sicherheitshinweise ........................43
4.Hinweise zu den einzelnen Vorgehensschritten ..45
5. Position von Warnschildern und Schutzvorrichtungen
an der Maschine .............................51
6.Schutzvorrichtungen .......................52
Skizze des Nähmaschinentisches ..............54
Aufstellen der Nähmaschine...................55
Drehrichtung des Maschinenrads ..............55
Einhängen der Kette für die Presserfußlüftung ....55
Schmierung................................56
Silikonöl für HR-Vorrichtung ...................57
Einfädeln ..................................58
Nadelwechsel ..............................59
Einstellen der Nadelfadenspannung ............59
Heraus-/Einklappen der Presserfußstange .......60
Einstellen des Presserfußdrucks ...............60
Einstellen des Differentialtransportverhältnisses ...61
Stichlängeneinstellung .......................61
Auswechseln des Obermessers................62
Auswechseln des Untermessers ...............62
Einstellen der Nahtbreite .....................63
Schleifen der Messer ........................63
Reinigen der Maschine .......................64
Ölwechsel .................................64
Ablassen des Öls ...........................64
Auswechseln der Hebelstütze des Presserfußes ...65
Positionieren und Einstellen des Fadengebers ....67
Positionieren der Fadenführungen / Einstellen der
Fadenmenge vom Nadelfadengeber ............67
M932 Positionieren der Fadenführungen ........68
M952 Positionieren der Fadenführungen ........69
Positionieren des Doppelkettenstich- Greiferfadenziehers
und der Fadenführungen Einstellen der Fadenmenge vom
Doppelkettenstich-Greiferfadenzieher .................70
Positionieren des Greiferfadenziehers und der -
führungen Einstellen der Fadenmenge vom
Greiferfadenzieher. . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Einstelltabelle ..............................72
Nadelvergleichstabelle/
Standardnadel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Technische Daten für die Unterklassen der Baureihe . . . . 74

CONTENIDO
目录
注记. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
指令. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
1. 前言 ...................................78
2. 警告标记 ...............................79
3. 安全措施 ...............................81
4. 各操作过程的注意事项 ...................83
5. 警告标签粘贴的位置与安全保护装置 .......89
6. 安全保护装置 ...........................90
台板的加工图...........................92
缝纫机的安装...........................93
缝纫机的旋转方向 .......................93
安装压脚链 ............................93
关于供油 ..............................94
给ＨＲ装置供油.........................95
穿线的方法 ............................96
机针的更换 ............................97
线状态的调节...........................97
压脚台的开和关.........................98
压脚压力的调节.........................98
差动比的调节...........................99
针脚长度的调节.........................99
上刀的更换 ...........................100
下刀的更换 ...........................100
链幅的调节 ...........................101
刀的研磨方法..........................101
缝纫机的清扫..........................102
机油的更换 ...........................102
排油的方法 ...........................102
改变压脚支点..........................104
针打线片的标准安装位置和调节 ...........105
针过线件的标准安装位置和打线量的调节....105
M932 针过线件的标准安装位置 ............106
M952 针过线件的标准安装位置 ............107
链弯针打线片和过线件的标准安装位置与
打线凸轮打线量的调节 ..................108
弯针打线片和过线件的标准安装位置与
打线凸轮打线量的调节 ..................109
调节基准表 ...........................110
针号对照表
标准用针 .............................111
子型号规格表..........................112
Copyright .................................77
Directivas..................................77
1.Introducción..............................78
2.Indicaciones de peligro, aviso y precaución.....79
3.Normas de seguridad ......................81
4.Observaciones sobre los procesos siguientes ...83
5.Posición de los letreros avisadores de peligro y
dispositivos protectores al lado de la máquina ....89
6.Dispositivos protectores ....................90
Diagrama esquemático de la mesa de la máquina de coser ...92
Instalación de máquina de coser ...............93
Sens de rotation du volant ....................93
Accrocher la chaîne du relève-pied .............93
Lubricación ................................94
Huile silicone pour dispositif HR................95
Enhebrado ................................96
Sustitución de la aguja .......................97
Ajuste de la tensión del hilo de la aguja..........97
Para desplegar y plegar la barra del prensatelas ..98
Ajuste de presión de prensatelas...............98
Ajuste de la relación del arrastre diferencial ......99
Ajuste de longitud de puntada .................99
Cambio de la cuchilla superior................100
Cambio de la cuchilla inferior .................100
Ajuste del ancho de la costura ................101
Afilado de las cuchillas ......................101
Limpieza de la máquina .....................102
Sustitución de aceite. . . . . . . . . . . . . . . . . . . . . . . . 102
Para purgar el aceite........................102
Para cambiar el fulcro en el prensatelas ........103
Posicionamiento y ajuste del tirahilos ..........105
Posicionamiento del guía-hilos / Ajuste de la cantidad
de hilo del tirahilos para la aguja .................105
M932 Posicionamiento del guía-hilos ..........106
M952 Posicionamiento del guía-hilos ..........107
Posicionamiento del tirahilos del garfio para cadeneta de
punto doble y de los guía-hilos Ajuste de la cantidad de
hilo del tirahilos del garfio para cadeneta de punto doble ....108
Posicionamiento del tirahilos del garfio y de las
guías de los hilos de los garfios Ajuste de la
cantidad de hilo del tirahilos del garfio .............109
Dimensiones de ajuste ......................110
Tabla de comparación de tamaños equivalentes/
Aguja estándar ............................111
Especificaciones de subclase ................112

Copyright
●This instruction manual may not be reproduced,
transcribed, transmitted, distributed or translated
into any language, in whole or part, in any form
or through a paper or electronic medium, without
the prior written permission from Pegasus Sewing
Machine Mfg. Co., Ltd.
●Disclaimer
The contents described in this instruction manual
are intended for giving information and subject
to change without notice. We assume no
responsibility for these information, and any errors
and/or incorrect descriptions that may appear in
this instruction manual.
●Pegasus Sewing Machine Mfg. Co., Ltd. has a
policy that we always modify the performance
and/or specifications of this product introducing
the state-of-the-art technology. Accordingly we
reserve the right to change the specifications
and/or design without notice.
●This instruction manual is valid for all the
models and subclasses listed in the chapter
"Specifications."
Directives
This machine is constructed in accordance with the
European regulations contained in the conformity
and manufacturer's declarations. In addition to this
instruction manual, strictly observe all the generally
accepted, statutory regulations, legal requirements
and all the environmental protection regulations.
Also rigidly adhere to the regionally valid regulations
of the social insurance society for occupational
accidents or other supervisory organizations.

Be sure to study very carefully forsafety.
安全のために必ずお読みください
注 記
●この取扱説明書のすべてあるいは一部を、ペガサス
ミシン製造株式会社の書面による事前の許可なく、
紙媒体であれ電子媒体であれ、無断で転載、複写、
翻訳、配布、配信することを固く禁じます。
●この取扱説明書に記載された内容は、情報の提供の
みを目的としており、予告なしに変更する場合があ
ります。
 これらの情報について当社はいかなる責任も負いま
せん。また、この取扱説明書に誤りや不正確な記述
があった場合にも、当社はいかなる責任、債務を負
わないものとします。
●ペガサスミシンでは、常に最先端の技術を導入して
いるので、本製品の性能・仕様を絶えず改良する方
針をとっています。したがって予告なく仕様・デザ
インを変更する権利を留保します。
●本書は「仕様」の章に記載されているすべてのモデ
ルとサブクラスに有効です。
指 令
このミシンは、ヨーロッパの安全規格の準拠と製造者
の告知を含むヨーロッパの安全規格にも合わせて組み
立てられています。この取扱説明書に加えて、一般的
に認められている制定法に従ったすべての規格と、法
律に基づく必要条件、及びすべての環境保護規格も厳
守してください。
作業中の事故に適用される社会保険の各規格、各地域
管理組織・機関などの規格も厳守してください。


1. はじめに
●本書は、当製品を安全に使用するための取扱説明書
です。
●当製品を使用する前に、必ず本書を読み、ミシンの
操作、点検、整備、保全等の方法を十分理解したう
えで、ご使用ください。
●工業用ミシンは縫製作業上、使用者は針などの運
動するミシン部品の至近距離で作業を行うため、運
動するミシン部品に接触してしまう危険性が常に
存在していることを認識しなければなりません。
このため安全を確保するためには、当社による安全
な製品の供給と、使用者による安全な正しい取り扱
いが不可欠です。お客様において安全対策が必要な
ものもいくつかありますので、ミシンをお使いにな
るすべての関係者が本書と駆動装置の取扱説明書を
合わせて熟読され、必要な安全対策を実施したうえ
で、ミシンを十分ご活用いただくようお願いします。
1.Introduction
●This is the instruction manual that describes how to
use this product safely.
●Read this instruction manual and learn very
carefully how to operate, adjust and service this
sewing machine before beginning any of the
procedures.
●You should realize first that there is always the
risk of contacting moving parts, such as needles
because you have to work at point-blank range
to them when you are operating industrial sewing
machines.
For safety it is essential that we supply safe
products and you use them correctly and safely.
There may be some safety measures
that you yourself must take.
Therefore, you should read and understand very
carefully this instruction manual together with that
of the driving equipment and take necessary safety
measures in order to use this machine efficiently
and effectively.
Be sure to study very carefully forsafety.
安全のために必ずお読みください

安全のために必ずお読みください Be sure to study very carefully forsafety.
2. 警告表示
当社省力装置および本書には、省力装置を安全にご使
用いただくために、警告表示を危険の程度により使い
分けています。これらの内容を十分に理解し、指示を
必ず守ってください。
警告ラベルは、常にはっきり見えるようにしておいて
下さい。
警告ラベルがはがれたり、汚れた場合は、新しいラベ
ルと交換してください。
交換用ラベルが必要な場合は、当社営業所までご連絡
ください。
2. Indications of dangers, warnings and cautions
To prevent accidents, indications (symbols and/or
signs) which show the degree of danger are used on
our products and in this manual. Study the contents
very carefully and follow the instructions.
Indication labels should be found easily.
Attach new labels when they are stained or removed.
Contact our sales office when new labels are needed.
警告
WARNING
危険
DANGER
注意
CAUTION
誤った取り扱いをしたときに、死
亡または重傷事故が発生する可能
性がきわめて高い危険。
Indicates an immediate hazard to
life or limb.
Indicates a potential hazard to life
or limb.
Indicates a possible mistake that
could result in injury or damage.
誤った取り扱いをしたときに、状
況によっては死亡または重傷事故
に結びつく可能性がある危険。
誤った取り扱いをしたときに、軽
傷または中程度の傷害および物的
損害のみの発生が想定される場合。
注意喚起シンボルとシグナル用語
Symbols, signs and/or signal words which
attract users' attention




 必ず指示内容に従い作業を行ってくださ
い。

 誤った取り扱いをしたときに、感電する可
 能性があります。
 誤った取り扱いをしたときに、手や指など
 のケガの原因になります。

 高温による火傷等の危険があります。

 絶対に行わないでください。



 修理時や調整等のメンテナンス作業の発生
 時や、落雷の可能性がある場合、電源プラ
 グを電源供給元のコンセントから必ず抜い
 てください。

 必ずアース線を接続してください。



 ミシンの正常なプーリー回転方向を示して
 います。
Be sure to follow the instructions when you
operate the machine and/or labor saving
device.
If you use the machine and/or labor saving
device incorrectly, you may get an electrical
shock.
If you use the machine and/or labor saving
device incorrectly, your hands and/or
fingers may be injured.
Unplug the machine and shut off the power
when checking, adjusting and/or repairing
t
he machine and/or labor saving device,
or when lightning may strike.
Denotes the normal rotating direction of the
machine pully.
If you use the machine and/or labor saving
device incorrectly, you may burn yourself.

 誤った取り扱いをしたときに、機械に手や
指などが挟み込まれ、傷害の原因になりま
す。

 誤った取り扱いをしたときに、発火する可
 能性があります。
If you use the machine and/or labor saving
device incorrectly, your fingers and/or hands
may be caught in them, causing
trouble.
If you use the machine and/or labor saving
device incorrectly, you may cause fire.
Never do this.
Be sure to connect to ground .
図記号の説明
Symbols and messages


 
󰴤




󰴥




 
 

 
 
  
 

 

 
󰴦





 



Be sure to study very carefully forsafety.
安全のために必ずお読みください
3.Safety precautions
󰴤Applications, purpose
Our industrial sewing machines have been developed in order to
increase quality and/or production in the sewing industry.
Accordingly never use our products for other than intended use
described above.
󰴥Circumstances
The environment in which our industrial sewing machines are used
may seriously affect their lives, functions, performance and/or
safety.
For safety, do not use the machine under the
circumstances below.
1.Do not use the machine near objects which make noise such as
a high-frequency welder, etc.
2.Do not use or store the machine in the air which has vapor from
chemicals, or do not expose the device to chemicals.
3.Do not leave the machine outside, in high temperatures or the
direct sun.
4.Do not use the machine in the places of high ambient
temperature and humidity that seriously affects sewing
machines.
5.Do not use the machine on the condition that the voltage
fluctuation range is more than ± 10% of the rated voltage.
6.Do not use the machine in the place where the supply voltage
specified for the control motor cannot be properly obtained.
7.Do not use the device at the place where the air supply specified
for the device cannot be properly obtained.
8.Do not expose the device to the water.
󰴦Safety measures
(1)Safety precautions when you perform maintenance on
the machine.
●Always turn off the power, unplug the machine and then make
sure that the machine does not run by pressing the treadle
before performing any maintenance, such as checking,
repairing, cleaning, etc. However, if you need to perform these
procedures with the power on, to prevent accidents due to
the unexpected start of the machine and users’ misoperation,
estabish your oun procedures for safety and follow them.

●Always turn off the power and unplug the machine
before performing the procedures shown below.
Sewing machine installation
Lubrication
Threading
Replacing the needle
Opening/closing the presser bar
Adjusting the stitch length
Replacing and adjusting the knife
Cleaning
Replacing the oil
Changing the fulcrum on the presser foot
Adjusting the needle thread take-up
Adjusting the thread take-up
Only authorized technicians are allowed to perform routine daily
maintenance and/or repair the machine.
●Do not modify the machine yourself.
※Consult you local Pegasus' sales office or representative for
modification
(2)Before operating the machine
Check the machine head and unit for any damage and/or faulty
function at the start of each day.
If there should be something wrong with the machine,
immediately perform repairs and/or other necessary
procedures.
Check by hand to see if the needle holder is
secured.
Be careful of the needle point.
Before starting the machine, make sure that
the presser foot is positioned correctly (turn the
machine pulley slowly by hand to see if the needle
point is centered in the needle drop hole on the
presser foot).
Check to see if the presser foot is secured (raise the
presser foot by the foot lifter and press it by hand
front to back and left to right).
●To prevent accidents, always make sure the safety
covers and safety guards are properly secured.
Never remove the safety covers and safety guards.
(3)Training
●To prevent accidents, operators and service/maintenance
personnel must have proper knowledge and skills for safe
operation.
To ensure so, managers must design and conduct training for
these people.

























 





 




 










 



安全のために必ずお読みください Be sure to study very carefully forsafety.
4.Notes for each procedure
CAUTION
󰴤Unpacking
1.The machine is packaged in a cardboard box before shipping.
Unpack your machine in orderly sequence while checking them
right-side up by referring to the indications, such as logo, etc.
printed on the boxes.
2.Never hold the area near the needle and/or thread guide related
parts when taking out the machine from the cushion.
Otherwise it may cause injury and/or damage to the machine.
3.Take out the machine very carefully while checking the position
of the center of the gravity.
4.Keep the cardboard box and packing carefully in case
secondary transport is needed in the future.
Disposal of the packaging
The packaging material of the machine consists of wood, paper,
cardboard and LDPE and foamed polystyrene. The proper
disposal of the packaging is the responsibility of the customer.
LDPE•••Low density Polyethylene
Disposal of machine waste
1.The proper disposal of machine waste is the responsibility of the
customer.
2.The materials used on the machines are steel, aluminum, brass
and various plastics.
3.The machine waste is to be disposed of in accordance with the
locally valid environmental protection regulations. A specialist
should be commissioned if necessary.
The parts contaminated with lubricants should be disposed
off separately according to the locally valid environmental
protection regulations.
Transport within the customer’s premises
The manufacturer assumes no liability for transport within the
customer’s premises. Care should be taken to transport the
machine in an upright position avoiding it from dropping or
falling down to the ground when it is moved.
 

󰴤
 


 


 

 



 


  

 
 󰬇

 









󰴥
 






 


 


 

 


󰴦

 
  
 

 

 


   
  
WARNING
󰴥Transportation
1.The machine should be carried by at least more than two people
when it is mounted on the table and/or a hand truck.
Be sure to use a hand truck for other transportation.
2.To carry the machine, hold the machine pulley
tightly with your right hand and the machine arm
with your left upper arm.
If the machine and/or your hands are stained
with oil, the machine may be easy to slip out of
your hands and fall to the floor. Therefore, wipe
off the oil carefully.
3.Care should be taken to avoid excessive shock and shake when
the machine is mounted on the table and/or transferred using a
hand truck. Otherwise the machine may fall down.
4.Wipe off the oil from the machine before packaging it again for
secondary transport. Otherwise the machine may easily slip out
of your hands or the bottom of the box may come off while in
transit.
CAUTION
󰴦Installation, preparation
Machine table
1.Use the machine table (table board, metal legs) that completely
carries the machine and is fully resistant to warping while the
machine is running.
2.Arrange the working environment for easy operation by
considering where to place the machine and the brightness
around the working area. If the illumination is insufficient,
control or change lighting as required.
3.Attach a non-slip pad to the treadle (foot switch).
Otherwise the operator may slip off the treadle while running the
machine, causing trouble.
4.Adjust the height of the table according to a working posture of
the operator.





 

 
  
 
 
       
  
 

 



 

 



1.  ( )
 OFF 


2.  ( )

3. 
4. 
5. 

6. 

WARNING
Cables
1.When connecting the cables between the machine and the
motor, be sure to turn off the power and connect each cable
connectors securely.
2.Do not strain the cables in use.
3. Do not bend the cables excessively.
4.When connecting the cables that are close to the moving parts,
such as pulley or V belt, keep a distance of 25mm at least
between them.
5.Protect each cable using a cover or adjusting its position if
necessary.
6. Never use staples to fasten the cables.
Otherwise it causes a short circuit and/or a fire.
CAUTION
Motor
1.Install the machine motor correctly by referring to the instruction
manual supplied by the manufacturer.
2.Select the machine motor equipped with the pulley cover so that
any part of your body etc. is not caught in the belt.
CAUTION
Connecting the air lines
1. Always turn off the power first and then connect the air lines to
the joints. Be sure to connect all the air lines before connecting
them to the air compressor.
2. When connecting the air lines to the joints, be sure to insert the
joints to the proper depth of the air lines and fasten securely.
3. Do not allow excessive force to be exerted on the air lines while
using the device.
4. Do not bend the air lines too much.
5. If necessary, protect the air lines by positioning them safely
and/or using the cover.
6. Do not use staples to secure the air lines. Otherwise it
may cause damage.



1. 

2. 


3. 
4. 
5. ( V ) 
 25mm 
6. 

7. 



 

 


󰴧
 


 

  

 

 
 


 


 


WARNING
Connecting the cords
1. When connecting the power cord, be sure to turn off the
power and disconnect the power plug.
2. Check the voltage designation to make sure the power
relay cord matches the local supply voltage. The use of wrong
cord may cause damage to parts and/or fire.
3. Do not allow excessive force to be exerted on the cords while
using the device.
4. Do not bend the cords too much.
5. Confirm that the cord is at least 25 mm away from moving part of
the machine and/or the device when you connect the cord.
6. If necessary, protect the cords by positioning them safely and/or
using the cover.
7. Do not use staples to secure the cords. Otherwise it may
cause damage.
CAUTION
Ground
1.Connect each of the ground wires in the sewing machine system
to the ground terminal. Do not connect to another devices’.
2. Connect the ground wires securely to the indicated
ground points on the machine head.
WARNING
󰴧Handling machine oil
1.Never start the machine with no oil in the reservoir.
Use the following oil.
Pegasus designated oil: HIGH SPEED SEWING MACHINE OIL
or Equivalents: Mobil Velocite SM22 manufactured by Mobil.
2.If machine oil gets in your eyes, it may cause eye irritation.
To prevent the machine oil from getting in your eyes, wear eye
protection.
Should machine oil gets in your eyes, wash them with fresh
water for 15 minutes and then go to see a doctor.
3.Avoid skin contact. Immediately wash contacted areas
completely with water and soap.
4. Never swallow machine oil.
5.Keep machine oil out of the reach of children.
If swallowed, do not induce vomiting.
Immediately go to see a doctor.
6.Dispose of the waste oil and/or containers properly as
demanded by law. If you have further questions on its disposal,
consult the store or shop at which you purchased it.
7.After opening the oil container, be sure to seal it to prevent dust
and water from getting into the oil and keep it in the dark to
avoid direct sunlight.


.
WARNING
󰴨Before starting the machine
Machine table
1.Before turning the power on, visually check the cables
and connectors for defective conditions, such as damage,
disconnection and/or loosening.
2. Never bring your hands close to the needle and/or pulley
when turning on the power.
3.When the machine is used for the first time,
turn on the power and then check the rotating
direction of the machine pulley.
The machine pulley should turn clockwise as
seen from the machine pulley.
4.Well trained operators and technicians are allowed to use the
machine after studying these precautions and the instruction
manual carefully.
5.Regarding symbols that indicate a danger or a warning, read
and study “2. Waning indications” carefully and give training on
safety to the operators as required.
6.Run the machine at the speed less than 3/4 of its maximum for
the first one month.
WARNING
󰴩Precautions while you are running the machine
1. Do not run the machine with the safety devices removed,
such as needle breakage shield, finger deflector, pulley cover,
etc.
2. Never bring your hands under the needle while running
the machine.
3.A clutch motor keeps on running for a while after the power is
turned off. Therefore, be careful even after the power is turned
off as the machine could start running by pressing the machine
treadle.
4. To prevent accidents, never bring any part of your fingers,
hair and clothes near the machine pulley, V belt, motor pulley,
thread take-up and needle bar. Also never leave scissors,
tweezers, tools, etc. around these areas.
5.Always turn off the power while the machine is not used or
before leaving the machine table.
6.In the event of a power failure, be sure to turn off the power.
7.While operating the machine, wear clothes that cannot be
caught in the machine.
8. Do not put any tools or other unnecessary objects on the
machine table while running the machine.
9. Pay close attention to the knife edges not to injure your
hands and/or fingers.

󰴨

 

 

 


 

 

  


       


󰴩
 

 

 


  


 

 
 

  

 



10.As a health hazard measure, users should wear ear protection
as required when the environmental nose level is “over 80 db or
under 85 db.” In addition, when the environmental noise level
is “over 85 db,” protections notifying the users that they should
wear ear protection should be posted.
CAUTION
󰴪Maintenance, Check, Repair
1.Well trained operators and technicians are allowed to perform
maintenance, check and repair of the machine after studying
these precautions and the instruction manual carefully.
2. If it is necessary to lay the machine backward for
maintenance, check and repair, always turn off the power,
unplug the machine and press the treadle to make sure that
the machine dose not operate before beginning any of the
procedures.
3. Before installing/removing the V belt, always turn off the
power, unplug the machine and press the treadle to make sure
the machine does not operate.
4.Carry out daily maintenance work and periodical inspections
properly by following these precautions and the instruction
manual.
5.Employ Pegasus’ genuine parts when repairing the machine
and/or replacing the parts. We are not responsible for accidents
caused by any improper repair/adjustment and substituting
other parts for thoes manufactured by Pegasus.
6.Do not attempt to modify the machine at your own discretion.
We are not responsible for accidents caused by the
modification.
7.Be sure to replace the safety devices and/or safety covers that
are temporarily removed for maintenance and/or adjustment.
8.After performing maintenance, check and repair, make sure that
turning on the power does not pose any danger to you.
9.To prevent accidents, be careful that any foreign matter such as
water, other liquids or metals do not get into the device.
10 .If the device is pneumatic,drain and clean the filter regulator
periodically.Otherwise the water drainage will flow into the
solenoid valve and/or air cylinder,causing trouble.
11 .Before and after use,clean lint and any other dust from the
machine and/or device. Otherwise it will cause trouble.
 
   
 



󰴪
 

 



  


 

 


 


 

 



 


 


5. 警告ラベルの貼り付け位置と
安全保護装置
5.Location of warning labels and safety
devices

安全のために必ずお読みください Be sure to study very carefully forsafety.
クロスプレート
Cloth plate
アイガード
Needle breakage shield
フィンガーガード
Finger deflector
前カバー
Front cover
プーリーカバー
Pulley cover
動く部分でケガをする。
Moving parts may cause injury.
安全保護装置をつけて縫製作業
をすること。
Operate with safety devices.
電源を切ってから糸通し、ボビ
ンや針の交換、掃除や調整をす
ること。
Turn off main switch before
threading, changing bobbin
and needle, cleaning etc.
警告ラベルWarning label
メス注意ラベル
Knife caution label
手や指を切る危険がありますので、
細心の注意を払って作業を行ってく
ださい。
In order to prevent injury to your
hands and/or fingers, great care
should be taken when you perform
the procedures.
アース接続指示ラベル
Ground connection label
アース線を接続しないと、感電や誤動作の原因とな
ります。
Be sure to connect the ground wire. Otherwise
electric shock and/or malfunction may occur.
プーリー注意ラベル
Pulley caution label
巻き込みによるケガを防ぐため、運転中は手、
頭髪、衣類を近づけないでください。
In order to prevent injury, do not let your hands,
hair and/or clothes get close to the machine
pulley while the machine is running.


6.Protectors for safety
This chapter describes each protector for safety. Therefore, read
and study the following carefully.
CAUTION
Protectors for safety
(1) Needle breakage shield
Never leave the needle breakage shield open.
For the safety of eyes, do not operate the machine with the nee
dle
breakage shield open. The needle breakage shield will prevent
any pieces of the broken needle from getting into your eyes if the
needle should break during sewing.
In addition, eye protection is recommended while the machine is
being used.
(2) Finger deflector
Never insert any of your fingers.
To prevent the needle that moves up and down from contacting
any of your body, the finger deflector is installed close to the
needle.
However, there is clearance above the finger deflector for easy
threading. Be careful that the needle may penetrate any of your
fingers if you insert it into this clearance.
(3) Pulley cover
Never remove.
The machine pulley and V belt are covered with the pulley cover.
The machine pulley and the V belt rotate at high speed during
sewing. To prevent accidents, operate the machine with the pulley
cover installed in place.
(4) Pulley
Check the direction in which the machine pulley rotates.
It should rotate clockwise as seen from the pulley.
(5) Presser foot
Never insert any of your fingers.
The presser foot lift (distance from the top surface of the needle
plate to the bottom of the presser foot) is more than 5.5 mm except
for some machines.
Be careful that none of your fingers are caught in this clearance.
Never insert any of your fingers under the presser foot when raising
the presser foot with the knee switch or automatically raising it with
the treadle.
 




 






 






 

  
    


 


 

  


