Pella architect series User manual

Fiberglass or Steel Entry Door Systems
Entry Door Owner’s Manual

Congratulations on the purchase of your entry door from Pella! You have joined
a select group of homeowners who have made their homes more beautiful and comfortable with
Pella® products for more than 85 years. No matter which of our three distinctive lines of entry doors
you have selected — Architect Series®, Pella or Encompass by Pella® — they all have one thing in
common: offering you more beauty, performance and value than any other door.
With proper installation, care and operation, your entry door will provide years of
enjoyment. Read this manual thoroughly during your first few days of ownership so you feel
comfortable operating, cleaning and maintaining your entry door. Then refer to it in the future,
should a question arise.
Entry door systems from Pella offer elegant decorative glass, stylish hardware and a variety
of finishes. But the real beauty of our fiberglass and steel entry doors is their outstanding
performance, energy efficiency and low-maintenance features that make your life easier.
Finally, rest assured that Pella will be here for you today … and for years to come. Your
complete satisfaction is of utmost importance to us. If you have any questions or concerns — or
would like to learn more about exclusive options available for your entry door — help is as close
as your local Pella Window and Door Showroom or pella.com. A commitment to service that’s as
strong as our windows and doors. Just another way Pella is creating a better view.

HOW TO USE YOUR ARCHITECT SERIES®, PELLA® AND
ENCOMPASS BY PELLA® ENTRY DOOR OWNER’S MANUAL
OVERVIEW
The Pella Entry Door Owner’s Manual contains specific information for troubleshooting and preventive maintenance to keep your entry door
system operating smoothly for years to come.
Architect Series®, Pella® and Encompass by Pella® Entry Door Owner’s Manual How to Use/Table of Contents
QUICK REFERENCE GUIDE
1.1 Door components
OPERATION
2.1 Multipoint locking system
2.1 Blinds-between-the-glass
CLEANING
3.1 Cleaning the glass
3.1 Spot-cleaning stubborn materials on all glass
3.1 Cleaning the door panel
3.1 Cleaning the exterior aluminum cladding
3.1 Cleaning hardware finishes
FINISHING
4.1 Overview
4.1 Before you begin
4.1 Fiberglass vs. steel
4.2 Finishing questions
4.2 Finishing tips
4.2 Cleaning the door panel and sidelights
4.2 Testing the stain
4.3 Staining fiberglass
4.3 Topcoat application — stain
4.4 Painting
4.4 Selecting your door paint
4.4 Painting fiberglass
4.4 Painting steel
4.5 Finishing the frames
4.5 Touch-up and repairs
4.5 Stain and topcoat
4.5 Paint
RECOMMENDED MAINTENANCE
5.1 Overview
5.1 Maintaining the interior
5.1 Maintaining the exterior
5.1 Salt spray environments Maintenance
TROUBLESHOOTING
6.1 Overview
6.1 Glass breakage or damage
6.1 Difficult operation
6.2 Water and air infiltration
6.2 Preventing roomside condensation
6.2 Understanding condensation
6.2 Humidity and condensation
6.2 Causes of condensation
6.2 Older vs. newer homes
6.3 Measuring and controlling humidity
6.3 Exterior condensation
6.3 Tips for wintertime moisture management
6.3 For more information … Maintenance
ADDITIONAL INFORMATION
7.1 Pella Unit ID: Service made simple
7.1 EIFS and synthetic stucco
7.1 Storm door usage recommendation
7.1 NFRC label
WARRANTY
Go to pella.com/warranty.

Frame. It’s the framework that surrounds and supports the entire door system.
• Architect Series® and Pella® entry doors — Wood frame is
dip-treated for longevity. Pine interior frames come fully
primed and ready to paint or are offered unfinished,
ready to be stained or factory-stained. Mahogany
interior frames are unfinished, ready to be stained
or painted. The exterior frame is offered with low-
maintenance aluminum cladding that doesn’t need
painting, primed Pine (Pella doors only), or unfinished
Mahogany that is ready to be stained or painted.
• Encompass by Pella® entry doors — The interior
and exterior frame provide the traditional beauty
of authentic wood and are fully primed and
ready to paint.
Frame corner construction. Wood frame corners are
sealed and mechanically fastened three ways — with
a mortise-and-tenon joint, a sealant and a metal
fastener — for exceptional strength and performance.
Pella Unit ID. To help save you time if your door ever
needs service or repair, Pella products include a special
identification number. On your entry door from Pella,
you’ll find the Pella Unit ID Number on the top hinge.
Insulated foam core. This insulation material inside the
door panel contributes to the door’s energy efficiency.
Steel deadbolt reinforcement plate. It provides added
security by reinforcing the deadbolt and strengthening
the door frame (single in-swing doors only).
Optional multipoint locking system. Architect Series
and Pella entry doors — Pella’s multipoint lock features
three dual-action deadbolts that extend into the door
frame when engaged for added security.
Sill/threshold. This is the bottom of the frame that
rests on the floor.
Door sweep. This energy-efficient and weather-resistant
weatherstripping system at the bottom of the door
forms a seal against air and water infiltration between
the door and the sill.
Weatherstripping system.
• Architect Series and Pella entry doors — Pella’s patent-
pending PerformaSeal™ design features exclusive
weathertight seal technology. Bulb-and-leaf
weatherstripping around the door frame prevents air and
water infiltration during even the most extreme wind and rain.
• Encompass by Pella entry doors — Foam compression weatherstripping system helps
prevent air and water infiltration around the perimeter of the door panel.
QUICK REFERENCE GUIDE
This diagram will help you identify the components of your entry door.
Architect Series®, Pella® and Encompass by Pella® Entry Door Owner’s Manual Quick Reference Guide
1.1

Architect Series®, Pella® and Encompass by Pella® Entry Door Owner’s Manual Operation
2.1
OPERATION
MULTIPOINT LOCKING SYSTEM
Available on Architect Series® and Pella® fiberglass (and steel) entry doors.
Pella’s multipoint lock features three dual-action deadbolts that extend into the door frame when
engaged. When disengaged, the deadbolts function as latches — disengage from the interior by
pressing down on the interior handle. If your door is equipped with an entrance-grip handle set,
squeeze the “trigger” to operate.
To engage the deadbolts, twist the thumbturn lock on the inside or turn the keylock on the outside.
The three latches will extend to their deadbolt position.
The multipoint lock includes a “panic” feature, which allows you to disengage the deadbolts and
operate the door with one smooth motion by pressing down on the interior handle. From the exterior,
insert the key into the keylock and turn to disengage.
CAUTION: Make sure the door is completely closed before engaging the multipoint
deadbolts. Failure to do so may damage the door’s finish or frame.
BLINDS-BETWEEN-THE-GLASS
Available on Pella entry doors.
The aluminum blinds-between-the-glass are permanently installed between panes of glass so they stay clean and never need to be removed.
Move the operators up and down in a slow and steady motion.
The operators are attached to the operating mechanism with high-powered
magnets. Moving the operators abruptly could cause them to become
disengaged from the magnet.
NOTE: If a handle becomes disengaged from the operator and remains
attached to the track, slide the operator up and down until the magnet
reengages. Slowly slide the handle all the way to the top of the track to fully
engage the handle with the operator.
NOTE: If the blind does not completely lower on one side, using the tilt
operator, ensure the slats are in the open position, then raise and lower
the blind.

Architect Series®, Pella® and Encompass by Pella® Entry Door Owner’s Manual Cleaning
3.1
CLEANING
CLEANING THE GLASS
To wash the glass:
1. Use a premixed vinegar-based cleaning solution (or make your own with one part white vinegar to 10 parts water), and apply to a soft,
clean, lint-free microfiber cloth or paper towel. Or you may use an ammonia-free glass cleaner such as Windex® (clear liquid) or Sparkle®
(purple liquid). Feel free to be generous with the amount of cleaner you apply, but avoid getting any cleaning solution on the door
panel as it may discolor the finish.
2. Rub from several different directions.
3. Rinse with clear water if streaks remain after cleaning.
CAUTION: Do not use glass cleaners that are ammonia- or alcohol-based. They may leave streaks or produce a film that attracts moisture or dust.
SPOT-CLEANING STUBBORN MATERIALS ON ALL GLASS
To remove any markings from grease, oil, tape adhesive, crayons or paint, or marks from plastics that may have come in contact with the glass:
1. Apply a small amount of a nonabrasive cleaner such as Bar Keepers Friend® (SerVaas Laboratories) to a clean, wet cloth — or apply a
solvent such as acetone or mineral spirits to a clean, dry, lint-free microfiber cloth or paper towel.
2. Rub on the areas of glass that need spot-cleaning. Avoid getting any cleanser or solvent on the door panel as it may discolor the finish.
3. Wipe clean using a clean, dry, lint-free microfiber cloth or paper towel.
4. Then clean the glass as instructed above.
CAUTION: Do not use a razor blade to scrape off stubborn materials — doing so may leave permanent marks on the glass or
scratches that could cause glass breakage. Contact the Pella Window and Door Showroom nearest you for special cleaning
instructions.
CLEANING THE DOOR PANEL
A warm, damp cloth and mild soap may be used on all Pella® fiberglass or steel entry door panels.
CLEANING THE EXTERIOR ALUMINUM CLADDING
Clean the surface with warm, soapy water. Stubborn stains and deposits may be removed with mineral spirits. If your cladding becomes dull,
you can use a quality car cleaner and wax to restore the shine. Should you need it, touch-up paint is available at the Pella Window and Door
Showroom nearest you.
CAUTION: Do not use abrasive or caustic solvents as they may damage your entry door. Do not scrape or use tools that might damage the surface.
Do not power-wash.
CLEANING HARDWARE FINISHES
A soft cloth and mild cleaner may be used on most hardware finishes for entry doors from Pella.

4.1
Architect Series®, Pella® and Encompass by Pella® Entry Door Owner’s Manual Finishing
FINISHING
OVERVIEW
If your entry door from Pella was delivered without an interior or exterior finish (paint or stain), you must
finish it within 30 days to protect your investment. Painting or staining and sealing help ensure your entry
door will beautify and protect your home the way it was designed to. Please note that failure to finish
your Pella® products in a timely manner may void their warranty. The Pella warranty does not cover issues
associated with improper finishing. Please refer to the warranty at pella.com/warranty.
Pella Corporation is recognized as a quality manufacturer of entry doors. However, your local paint
professional is the best source for expert advice on finishing your door. Whether you choose to stain your
new entry door or paint it to match your interior décor, be sure to consult your local finishing professional
and follow the recommendations in this manual to achieve maximum beauty and performance from your
entry door.
NOTE: For a professional-looking painted finish, it’s important to use quality brush or spray techniques.
Contact your local paint professional for recommendations.
NOTE: Installation of a steel entry door within five miles of a seacoast is not recommended due to the risk of corrosion, and it will void Pella’s
steel entry door warranty.
BEFORE YOU BEGIN
Before finishing your entry door system from Pella, you must know whether your entry door panel and sidelights are fiberglass or steel. If
you’re unsure if your entry door is made of fiberglass or steel, place a small magnet on your door — if it sticks, it is most likely steel. Your Pella
packaging and/or sales invoice should indicate the door type, or check with your Pella representative for specific information on your product.
Fiberglass vs. steel
• Mahogany-, Oak-, Rustic- and Hemlock-grain fiberglass doors and sidelights can be gel-stained for the beautiful look of wood or painted
to complement the colors of your home’s exterior or interior trim. Finishing is required.
• Smooth fiberglass doors and sidelights can be painted but not stained. Painting is required.
• Steel doors are factory-primed and can be painted but not stained. Painting is required.
• Exterior frames are either primed wood or low-maintenance EnduraClad® aluminum cladding. Primed wood exterior frames must be
painted. Unfinished Mahogany frames are ready to paint or stain. Please consult your Pella retailer if you need assistance identifying the
materials used in your entry door system.
Mahogany-Grain Fiberglass Oak-Grain Fiberglass
Rustic-Grain Fiberglass Hemlock-Grain Fiberglass
Unfinished premium-grain fiberglass panels are also available.
Architect Series®
Prefinished Premium-Grain Finishes
Mahogany-Grain Fiberglass Oak-Grain Fiberglass
Painted Smooth Fiberglass
Unfinished fiberglass and steel panels are also available.
Pella®
Prefinished Fiberglass and Steel
Smooth Fiberglass
Steel
Encompass by Pella®
Unfinished Fiberglass and Steel
Painted Smooth Steel

4.2
Finishing questions
Your local paint/finish store representative can best address your specific finishing needs. Here are some questions you should ask:
• What are my finish options?
• Which finishes perform best in my region of the country?
• How does the temperature and humidity level at the time of finishing affect my results?
• Should I use an interior or exterior product?
• What do I need to know about product compatibility — for example, between the prestain, stain and finish coats?
• What else should be considered to obtain the best results?
CAUTION: To maintain proper product performance, DO NOT remove factory-installed weatherstripping, dust pads or gaskets when finishing your
products. Air and water leakage may result and will void the warranty if factory-installed items are removed. Instead, we recommend taping off these items
to protect them during the finishing process.
NOTE: Always wear protective personal equipment when sanding, and read and follow the manufacturer’s directions for proper use and disposal of
paint, stain or other finishing materials.
Finishing tips
• Only stain, paint or apply topcoat when the temperature is between 50° F (10° C) and 90° F (32° C) and humidity is between
30% and 70%.
• Only apply finishes in a well-ventilated area.
• Paint, stain and apply topcoat to all exposed unfinished edges and surfaces of the door and frame.
• All exterior exposed surfaces should be finished within 30 days of initial exposure.
• Do not apply finish of any kind in direct sunlight.
• Do not sand the fiberglass door.
CLEANING THE DOOR PANEL AND SIDELIGHTS
Using a clean, dry rag, wipe the entire surface of the door with mineral spirits for fiberglass panels and water for steel panels. Allow the door
to dry completely. Then mask all hinges, glass and weatherstripping to prevent the finish from coming in contact with these components.
Mask all areas on the unit that you do not wish to finish. Remove or mask any additional hardware on the door (handle, kick plate, etc.) prior
to finishing.
TESTING THE STAIN
Prior to finishing your panel, color-test the stain. After stirring the stain well, apply it to a skin sample with a lint-free cloth; then use a 3" brush
to brush out the stain to the desired shade. If you do not like the shade of stain, use mineral spirits and a clean rag to remove the stain and
repeat stain application until desired look is achieved — then allow six to eight hours for stain to dry. When you have achieved the desired
shade of stain, set the practice piece to the side and keep it to match to the final product.
NOTE: A stain shade can be controlled by the amount of dry time before brushing out the stain and the amount of pressure used to brush out the stain.
Apply stain lightly at first. An additional coat of stain may be applied after eight hours. The more stain you apply, the darker the stain will look.
DO NOT remove
weatherstripping,
dust pads
or gaskets.
Architect Series®, Pella® and Encompass by Pella® Entry Door Owner’s Manual Finishing

4.3
STAINING FIBERGLASS
If a stained wood appearance is desired on wood-grain fiberglass door panels, sidelights and glass frames, apply gel stain and clear finish
according to the stain manufacturer’s directions. For best results, always apply stain in the direction of the grain. Be sure to finish door edges.
1. Stir stain well.
2. Using a stain sponge or brush, apply the stain to the components of the door first. The components that may be stained include the door
edges, brickmould, jambs, mullions, glazing frames and wood frames (see “Finishing the frames” on page 4.5).
3. For the panel, work the stain first into the flat portions of the grain and then into the grooves surrounding them by rubbing stain in a
circular motion with a stain sponge.
4. Stain the wood edge of the door.
5. Stain all the interior-most section(s) of the door panel, and gradually work toward the outside of the panel.
6. Stain all sections perpendicular to the interior section(s) just stained.
7. Stain the outermost sections of the door panel.
8. After the entire door has been covered with stain, use your sponge and lightly drag it in the same direction as the grain in each section to
remove any swirl marks in the stain.
9. Add texture to the stain for a natural look.
• Mahogany-, Oak-, Rustic- and Hemlock-grain entry doors: After the desired color has been achieved, but before the stain
has dried, “feather” the stain in the direction of the grain using a clean, dry 3" bristle brush to remove any blotchy areas and blend
areas of heavy or light stain. Dab brush in corners and crevices to pull out excess stain.
10. Allow stain to dry completely (at least eight hours) before proceeding.
11. Remove excess stain on brush by wiping brush on a dry cloth.
12. Clean brush with mineral spirits when finished.
NOTE: Optimal drying conditions are between 50° and 90° F and between 30% and 70% humidity. Since drying time varies depending on temperature
and humidity levels, drying time may increase if staining is done in lower temperatures and/or higher humidity than suggested.
13. If a darker stain color is desired, repeat Steps 3 – 8 to apply a second coat.
NOTE: Be sure to clean brush thoroughly if it will also be used to apply the clear topcoat. Otherwise, dispose of brush.
14. Dispose of waste according to local regulations.
Topcoat application — stain
Allow the stain to dry at least 48 hours prior to applying topcoat. To test for dryness, get stain sample done prior to staining door and place
a piece of masking tape over stain. Rub tape onto surface, and in one quick motion, remove tape. If no stain is removed, the stain is dry. It is
recommended that the door panel is recoated with topcoat every 18 – 24 months. Failure to do so may void manufacturer’s warranty. Please
see your manufacturer’s warranty information for more details.
NOTE: A minimum of two coats is recommended. For exterior exposures, a minimum of three coats is recommended.
1. Stir topcoat well.
2. Wet only the tip of the brush, and apply one thin coat. Brush in the direction of the grain.
3. Apply topcoat to various door components and door panel parts in the same sequence as the stain was applied.
4. Clean brush with mineral spirits or paint thinner.
5. Wait at least six hours between each application of the topcoat. Finish must be completely dry before applying the next coat.
Do not sand between coats.
6. Repeat Steps 1 – 4 for each additional coat applied.
Architect Series®, Pella® and Encompass by Pella® Entry Door Owner’s Manual Finishing

PAINTING
Selecting your door paint
If you are going to paint your entry door panel, be sure to ask a qualified paint/finishing professional to recommend a paint with good blocking
resistance. Don’t rely on a paint’s price or brand name in making your selection — an expensive paint may not necessarily offer good blocking
resistance. Failure to use a high-quality paint with good blocking resistance may result in a door that sticks shut even after the paint has dried.
PAINTING FIBERGLASS
Promptly paint all exterior surfaces, including door panel edges, with two coats of quality exterior paint with good blocking resistance.
Then paint all interior surfaces with two coats of quality interior paint with good blocking resistance.
NOTE: Applying thick layers of paint may hide the texture of the door panel.
1. Stir paint well.
2. Wet only the tip of the brush, and apply one thin coat. Brush in the direction of the grain.
3. Apply paint to various door components first, such as the door edges, brickmould, jambs, mullions, glazing frames and wood frames.
Then paint the panel.
4. Clean brush.
5. Wait at least six hours between each coat application of the paint. Finish must be completely dry before applying the next coat.
Do not sand between coats.
6. Repeat Steps 1 – 4 for each additional coat applied.
NOTE: A primer may be necessary to get proper adhesion. Contact your local paint supplier to determine if a primer is necessary with the selected paint.
CAUTION: Finish all exposed door panel edges, including the top edge. This helps reduce the chance of warping. After finishing the entry door system,
allow the door to dry completely, in accordance with the paint manufacturer’s directions, before closing it.
PAINTING STEEL
Steel doors and sidelights are factory-primed and do not need additional priming. They must be painted promptly after wiping the door
with a clean, damp cloth to remove loose dust and dirt. Paint all exterior surfaces with two coats of quality exterior paint with good blocking
resistance — including the glazing frame, if applicable, and the door panel edges. Paint all interior surfaces with two coats of quality interior
paint with good blocking resistance. Paint can be either brushed or sprayed on.
NOTE: Applying thick layers of paint may hide the grain texture of the door panel.
1. Stir paint well.
2. Wet only the tip of the brush, and apply one thin coat. Brush in the direction of the grain.
3. Apply paint to various door components first, such as the door edges, brickmould, jambs, mullions, glazing frames and wood frames.
Then paint the panel.
4. Clean brush.
5. Wait at least six hours between each coat application of the paint. Finish must be completely dry before applying the next coat.
Do not sand between coats.
6. Repeat Steps 1 – 4 for each additional coat applied.
CAUTION: Finish all exposed door panel edges, including the top edge; this helps reduce the chance of warping. After finishing the entry door system,
allow the door to dry completely, in accordance with the paint manufacturer’s directions, before closing it.
4.4
Architect Series®, Pella® and Encompass by Pella® Entry Door Owner’s Manual Finishing

FINISHING THE FRAMES
• Factory-primed interior frames — If you have purchased wood frames with factory-primed interiors, be sure to clean the surface and paint
all surfaces promptly with two coats of quality interior paint.
• Unprimed interior frames — If the interiors of your door and sidelight frames are not factory-primed, they may be stained. Apply stain and
clear finish according to the manufacturer’s directions.
• Primed Pine exterior frames — The exteriors of Pine wood frames are factory-primed, but the factory-applied primer is not intended
for long-term exterior exposure. The exterior wood frame must be painted immediately after installation. Clean the surface, and finish
promptly with two coats of quality exterior paint.
• Mahogany exterior frames — Your unfinished Mahogany door exterior frame may be stained. Apply a stain and clear finish according to
the manufacturer’s directions.
• Aluminum-clad exterior frames — The aluminum-clad exterior protected by the Pella® EnduraClad® finish doesn’t need painting. Clean the
surface with warm, soapy water. Stubborn stains and deposits may be removed with mineral spirits.
CAUTION: Do not use abrasive or caustic solvents as they may damage your entry door. Do not scrape or use tools that might damage the surface.
Do not power-wash.
If your cladding becomes dull, you can use a quality car cleaner and wax to restore the shine. Should you need it, touch-up paint is available
at the Pella Window and Door Showroom nearest you.
TOUCH-UP AND REPAIRS
Stain and topcoat
NOTE: Do not sand damaged area.
1. Wipe damaged area using a clean cotton swab or cotton rag damp with mineral spirits. Allow area to completely dry before applying stain.
2. Make sure the color-matched stain is shaken/mixed well before using for touch-up.
3. Apply stain to damaged area using an artist brush. DO NOT over-brush the area.
4. Dab at the freshly applied stain with a cotton swab until color match is achieved.
NOTE: Repeat stain application and dabbing until desired look is achieved. Allow newly stained area to dry before applying topcoat.
5. Using a polyurethane varnish, apply a fine coat of topcoat over the restained area with a clean artist’s brush. Blend as necessary.
NOTE: The size of touch-ups should be kept to a minimum.
Paint
NOTE: Do not sand damaged area.
1. Wipe damaged area using a clean cotton swab or cotton rag damp with water. Allow area to completely dry before applying paint.
2. Make sure the color-matched paint is shaken/mixed well before using for touch-up
3. Apply a thin layer of color-matched paint to damaged area using an artist’s brush.
NOTE: Use a finer brush for smaller scratches or scuffs.
CAUTIONS:
• Avoid inhalation of fumes or ingestion of stains, topcoats or paints. Follow material-specific safety instructions if necessary.
• Only use materials in a well-ventilated area.
• Keep all materials out of the reach of children.
• Close all containers when not in use.
4.5
Architect Series®, Pella® and Encompass by Pella® Entry Door Owner’s Manual Finishing

RECOMMENDED MAINTENANCE
OVERVIEW
Pella recommends you inspect your entry door at least annually as part of a home checkup. Recommended maintenance can prolong the
life of your entry door and will help ensure maximum warranty coverage. It is recommended that the door panel be recoated with a topcoat
every 18 – 24 months. Failure to do so may void manufacturer’s warranty. Please see your manufacturer’s warranty information for more
details. As needed, clean, repaint or restain your entry door, and recaulk around it to help maintain optimal performance. Also, be sure to
regularly check for leaks and improper drainage above or around vents and sprinkler systems that may subject your entry door to prolonged
water exposure. With recommended care, entry doors from Pella can reward you with decades of beauty and performance.
Maintaining the interior
At least once a year, inspect the interior finish of your entry door to make certain that the painted or stained finish is in good condition.
Ultraviolet rays from the sun can break down the finish and compromise its protective features.
Maintaining the exterior
An annual checkup can help preserve and maintain the beauty of your Pella® products for years to come. Inspect the sealant/caulking on the
exterior perimeter of your entry door at least once a year. The sealant/caulking helps create a watertight seal between the door frame and
the exterior siding (whether it is vinyl, cedar, aluminum, brick, etc.). It is extremely important that the sealant/caulking remains intact and in
good condition at all times. The sealant material should not be cracked, broken or missing — or it may cause premature failure of your entry
door or other parts of your home. Deterioration that occurs as a result of improper or insufficient maintenance is not covered by the Pella
warranty. At the same time, check the exterior paint for corrosion, peeling and/or cracking. If the exterior surface indicates any deterioration,
problem areas must be touched up as soon as possible to prevent further damage. Instructions and touch-up paint for aluminum-clad
products are available from the Pella Window and Door Showroom nearest you.
Salt spray environments
The seacoast environment is extremely hard on all sorts of products (automobiles, recreational vehicles, building products, etc.). Any
product used in a seacoast location will require more frequent inspection and maintenance to help it last as long as possible in this harsh
environment. Entry doors are no different from other products in this respect.
If your home is in a coastal environment and is subjected to wind-driven salt spray or salt fog, use a mild detergent soap and water to clean exterior cladding
and operating hardware at least quarterly — and more often, if necessary — to prevent salt or other abrasive materials from building up.
CAUTION: Do not power-wash.
NOTE: Installation of a steel entry door within five miles of a seacoast is not recommended due to the risk of corrosion, and it will void Pella’s
steel entry door warranty.
Architect Series®, Pella® and Encompass by Pella® Entry Door Owner’s Manual Recommended Maintenance
5.1

Architect Series®, Pella® and Encompass by Pella® Entry Door Owner’s Manual Troubleshooting
6.1
TROUBLESHOOTING
OVERVIEW
If you have a concern with your entry door from Pella or need additional assistance from an experienced professional, go online and visit pella.
com and look under “Where To Buy,” or consult your Yellow Pages (under “Windows) for the Pella Window and Door Showroom nearest you.
Glass breakage or damage
In the event of glass breakage, consult the Pella Window and Door Showroom nearest you for assistance. Be sure to have your Pella Unit ID
Number handy (see “Pella Unit ID: Service made simple” on page 7.1). For safety reasons and to ensure optimum performance, we strongly
advise you consult a professional for glass replacement.
Most U.S. and Canadian local codes require the use of tempered glass in doors and other specific applications. Tempered glass can withstand
greater impact than ordinary glass, but it is sensitive to scratches. Scratches can cause immediate or delayed breakage. If the glass is tempered,
it will break into small, rounded pieces. If tempered glass is broken, likely by law it must be reglazed or replaced with tempered glass.
Difficult operation
Adjusting the threshold — Encompass by Pella® entry doors.
If the bottom of the door sweep is not making contact or if it is too tight, adjustments to the threshold may be needed. To lower the threshold,
turn the screw clockwise, and turn counterclockwise to raise it. If the door sweep is damaged, loose or brittle, reattach or replace the sweep.
Frame adjustment
Another possibility is that the frame is not square. Measure the diagonal dimensions. If the two
measurements are more than 1/8" in difference, the door may need to be reinstalled or panels may
need to be adjusted accordingly.
Door adjustment
• Hinge shim adjustment
If the screws are loose at the hinge areas, tighten up all screws at the hinges. You may have to replace or add plastic shims as needed in each hinge.
Additional adjustments can be provided by your Pella service specialist at the Pella Window and Door Showroom nearest you.
• Adjustable hinges — optional on Architect Series® and Pella entry doors.
The door panels have adjustable hinge leaves. Using a 1/8" allen wrench, turn the center screw clockwise to increase the space between
the hinge side of the frame and the door panel, or counterclockwise to increase the space between the door panel and the lock side of
the frame. DO NOT turn the screws more than a 3/4 turn in either direction. In some cases, it may be necessary to loosen and then
tighten the top and bottom hinge screws to obtain full hinge adjustment. If necessary, loosen the top and bottom screws and immediately
retighten them. With the screws retightened, turn the adjustment hinge screw. If the hinge will not adjust any further, it is adjusted as far as
it will go. If more clearance is needed, adjust the shims between the frame and rough opening.
NOTE: DO NOT adjust the hinge with the top and bottom screws loose; this could force the hinge to adjust beyond its design capability,
which could cause the hinge to bind, could damage the hinge and/or could pull out the screws. A 3/4 turn of the center screw provides approximately
1/16" adjustment.

6.2
Water and air infiltration
Loose, brittle or damaged weatherstrip
Roll the weatherstrip back into the frame if it is loose; replace the weatherstrip if it’s brittle or damaged. Also make sure that the weatherstrip
joints at the head and jambs are closed. If not, remove the jamb weatherstrip and reinstall it higher up the jamb.
Loose, brittle or damaged door bottom seals
If the panel door bottom seals are missing, misplaced, brittle or damaged, they must be replaced. Contact your Pella service specialist.
Frame or panel not square
Infiltration can also be caused by a frame that is not square, preventing adequate slab-to-frame contact. Try tightening or loosening the
hinge screws or adding or subtracting shims. On Pella and Architect Series entry doors — if equipped with adjustable hinges — you may also
be able to make simple adjustments. On Encompass by Pella entry doors, you may replace the current weatherstrip with a long-reach frame
weatherstrip in the head and lock jamb.
If the door panel appears to be bowed, stretch a string from top to bottom straight along the panel. If there’s a 1/4" or larger gap between
the door leaf and the string, the panel has bowed sufficiently to cause operational problems.
PREVENTING ROOMSIDE CONDENSATION
Understanding condensation
Moisture is present in all homes, but when it becomes excessive, homeowners need to take an active role in protecting their investment.
Humidity and condensation
Humidity is a measure of the amount of water vapor in the air.
Condensation is water that forms when warm, moist air hits a cooler surface. In homes, it might occur on surfaces such as windows, doors,
mirrors, bathroom walls and cold-water pipes.
When interior humidity levels are high, relative to cooler outdoor temperatures, condensation can form on the coldest surface in a room —
often the glass in a window or door. While windows and doors do not cause condensation, they may be one of the first places it shows up.
Causes of condensation
Excess humidity is typically the cause of condensation. There are many sources for moisture in a home: showers, dishwashers, clothes
washers and dryers, house plants, humans and pets, among others. In newly built homes, additional moisture may escape from building
materials such as lumber, plaster and masonry for up to three heating seasons, even with proper airflow and temperature management.
Older vs. newer homes
Condensation may be less of an issue in older homes if conditions allow for more air exchange between indoors and out, often from around
aging, loose or poorly installed windows and doors. However, the tradeoff is higher energy costs. When replacement windows and doors are
properly installed and the airflow around them decreases, condensation may form on the glass of the new windows and doors.
Newer homes, on the other hand, are more airtight and energy-efficient. Many have vapor barriers — plastic within the wall cavity blocking
moisture passage in either direction. With tighter-fitting windows and doors, vapor barriers and increased insulation, energy costs are lower,
but humidity levels must be monitored more closely.
No matter when your home was built, the key is to strike the right balance when it comes to humidity levels. Air that’s too dry can cause the
following: furniture to dry out and crack; joints and studs to shrink and twist; paint and plaster to crack. Excessive moisture in the home can
cause paint to peel and insulation to deteriorate, and condensation on windows and doors can damage sills and trim.
Architect Series®, Pella® and Encompass by Pella® Entry Door Owner’s Manual Troubleshooting

Measuring and controlling humidity
To determine how much humidity is present in your home, you can purchase a humidity
gauge from a hardware store or home center. Invest in a quality unit for greater potential
accuracy in assessing humidity levels, or consult an expert. Another way to monitor the
interior humidity level is to watch your windows and doors. When interior condensation
begins to form, wipe it off. To reduce the humidity, open windows, run exhaust fans or
dehumidifiers, or minimize sources of moisture.
Exterior condensation
Exterior condensation on windows and doors occurs primarily in the morning when days are warm and humid, but nights are cool. Typically, it
clears as the day warms. Exterior condensation can occur at any time, especially in warm, humid climates where interior temperatures are cooler
than outdoor conditions. Exterior condensation means that windows and doors are doing their job properly. However, if you spot excessive
condensation on the inside of your windows or doors, check your inside humidity — it may be a signal of potential problems if not addressed.
Tips for wintertime moisture management
• Open window coverings — such as blinds, shades, drapes and curtains — during daylight hours to increase airflow over the glass.
• Closely monitor the furnace humidifier and any other humidifying devices.
• Be sure louvers and vents for the attic, basement and/or crawl space are open, adequately sized and cross-ventilated.
• Run exhaust fans for kitchen, bathroom and laundry rooms for longer periods.
• Make sure exhaust fans vent directly outside, not into attics or crawl spaces.
• Be sure chimneys are free and clear so moisture in combustion gases can escape.
• Follow the manufacturer’s instructions for venting gas appliances. In most cases, that will mean directing vents to the outside of the home.
• Make sure your furnace is in proper working order and is serviced regularly.
• Store firewood outside or in the garage — as wood dries, it gives off moisture.
• Install energy-efficient products, such as those that have earned the ENERGY STAR® rating.
For more information on condensation in the home, consult the following:
• Home Moisture Problems (Series 1437), published by the Oregon State University Extension Services,
http://extension.oregonstate.edu/catalog/. Search for “condensation.”
• The University of Minnesota Extensions: http://extensions.umn.edu. Search for “condensation.”
• Window and Door Manufacturer’s Association: www.wdma.com. Search for “condensation.”
• University Wisconsin Extensions: www.uwex.edu. Search for “condensation.”
• Efficient Windows Collaborative: www.efficientwindows.org. Search for “condensation.”
NOTE: Condensation that forms in between the panes of insulating glass is not considered “roomside” condensation. Instead, this is an indication of glass
seal failure, which cannot be corrected. Contact your Pella representative if this occurs.
6.3
Architect Series®, Pella® and Encompass by Pella® Entry Door Owner’s Manual Troubleshooting
Maximum Recommended Humidity Levels
Outside Temperature Inside Humidity
20º F to 40º F Not over 40%
10º F to 20º F Not over 35%
0º F to 10º F Not over 30%
-10º F to 0º F Not over 25%
-20º F to -10º F Not over 20%
-20º F or below Not over 15%
Based on engineering studies at 70º F conducted at the
University of Minnesota Laboratories.

ADDITIONAL INFORMATION
PELLA UNIT ID: SERVICE MADE SIMPLE
To help save you time if your product ever needs service or repair, all entry doors sold by Pella include a special
identification number. On your entry door, you’ll find the Pella Unit ID Number on the top hinge.
EIFS AND SYNTHETIC STUCCO
Pella® products should not be used in barrier wall systems that do not allow for proper management of moisture within the wall systems, such
as Exterior Insulated Finish Systems (EIFS) (also known as synthetic stucco) or similar systems. Except in the states of California, New Mexico,
Arizona, Nevada, Utah and Colorado, Pella makes no warranty of any kind on and assumes no responsibility for Pella windows and doors
installed in barrier wall systems. In the states listed above, the installation of Pella products in EIFS or similar barrier systems must be in
accordance with Pella’s instructions for that type of construction.
STORM DOOR USAGE RECOMMENDATION
Entry door systems from Pella are designed to be compatible with the installation of a Pella storm door.
• A ventilating Pella storm door is optimal for use with an entry door from Pella.
• The use of a storm door of any type in higher temperature climates is not recommended.
• The combination of a darker color and direct sun can affect the panel material of an entry door from Pella when a storm door is used.
• The use of the ventilating screen is recommended during the summer months when using a fullview storm door with an entry door
from Pella.
NFRC LABEL
What’s so special about the National Fenestration Rating Council (NFRC) label?
It represents one standard testing method from an independent source for all kinds and
brands of windows and doors. It replaces a system of individual manufacturers testing their
own products with many different testing standards. With this label, you can make direct
comparisons. Keep in mind, energy efficiency is just one of the many important qualities to look
for in windows and doors. The NFRC has one single purpose: to establish and improve upon
uniform energy-rating procedures for all brands of windows and doors.
This nonpartisan coalition of professionals includes home and commercial builders, product
designers and specifiers, manufacturers, consumer advocates, utility company energy specialists,
and government agencies.
Pella Corporation is a member of the NFRC and supports its work on behalf of homeowners
and the building industry. If you have any questions about the NFRC, feel free to write to NFRC,
6350 Ivy Lane, Suite 104, Greenbelt, MD 20770 — or call 301-589-1776, fax [phone] or
visit nfrc.org.
Architect Series®, Pella® and Encompass by Pella® Entry Door Owner’s Manual Additional Information
7.1
NOTE: For example purposes only.
NFRC ratings will vary by product.
Unit ID Number
Pella Corporation
Entry Door
In-Swing
Not Applicable
PEL – X – XXX
ENERGY PERFORMANCE RATINGS
U-Factor Solar Heat Gain Coefficient
0.14 5.68 0.005
ADDITIONAL PERFORMANCE RATINGS
Visible Transmittance
0.00 – –
Manufacturer stipulates that these ratings conform to applicable NFRC procedures for determining
whole product performance. NFRC ratings are determined for a fixed set of environmental conditions
and a specific product size. NFRC does not recommend any products and does not warrant
the suitability of any product for any specific use. For more information, call [phone]
or visit Pella’s web site at www.pella.com or visit NFRC’s web site at www.nfrc.org.
Wind Load
Design Pressure
(DP) (psf)
+ 40 / – 40
(Per ASTM E330)
ENERGY STAR® Qualified
In All 50 States
Air / Water
Performance
Air Leakage
0.30 CFM/Ft2
per ASTM E283
Water Performance
3.7 psf
per ASTM E547
WDMA DP40 (Design Pressure 40 psf)
ASTM E330
Structural Only
HALLMARK
WINDOW AND DOOR
MANUFACTURERS ASSOCIATION
www.wdma.com CERTIFIED
WDMA License Number: XXX-X-XXX
Manufacturer Stipulates Conformance to the applicable standards.
WDMA Hallmark Certification. Pella products labeled with the Window & Door Manufacturers
Association (WDMA) Hallmark Certification are tested in accordance with applicable WDMA performance
standards, which requires products be tested for air infiltration, water infiltration and structural performance.
Performance of Pella products will change over time depending upon the conditions of use. For details on
Hallmark Certification, go to www.wdma.com.
Meets or exceeds M.E.C., C.E.C., & I.E.C.C. Air Infiltration Requirements
Glazing type & thickness: Not Applicable3.0MMboth panes, designed per ASTM E1300
Window or Door Actual Size: 37.500" wide by 81.500" tall
6210066 – 4 – 1 – NFRC.CCTHERMAUM
Field_Name_6210066 – 4 – 1 – NFRC.ZZTHERMAUM
(Metric/SI)(U.S./I – P)
Does this door meet the criteria
for its glazing level? (Check only one box)
For: U-factor SHGC Yes
Opaque ≤ 0.21 Any X
¼ or ½ Lite ≤ 0.27 ≤ 0.30
¾ or Full Lite ≤ 0.32 ≤ 0.30
Remove this label after final inspection; SAVE for future reference