Pelpro FPP User manual

READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE YOUR HEATER.
FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE,
BODILY INJURY OR EVEN DEATH!
Installation shall conform to CAN/CSA B365 Installation Code for Solid-Fuel-Burning Appliances and
Equipment in Canada and NFPA 211 Chimney, Fireplaces, Vents and Solid Fuel Burning Appliances in the US
.
My local “Pelpro” dealer is:
Manufactured by:
Contact local building or fire officials about restrictions and installation inspection requirements in your area.
Toll Free Technical Support
1 - 866 - 456 -9269
To register your purchase
www.dansons.com/support
FPP
Bay View Freestanding
IPP
Bay View Insert / Built-In
FPP
Freestanding
IPP
Insert / Built-In

Canadian Comfort Industries V04 2 PELPRO OWNERS MANUAL
Copyright 2004 www.pelprostoves.com Dansons Group Inc.
Dear PELPRO Pellet Stove Owner:
CONGRATULATIONS on the purchase of your PELPRO wood pellet appliance! You have selected the finest in
residential wood pellet heating technology.
Let us pass on a few "tips" concerning installing your stove and heating with wood pellets.
1. Whether you install your stove yourself or hire a professional installer, a quality installation
is a must for the safety of your family and for efficient, satisfactory operation of your stove.
2. Initial Burn Setup of the stove is the most important step to ensure the efficient and satisfactory
operation of your appliance for many years to come.
3. Know the quality and characteristics of the pellets you burn. Pellets can vary greatly from
company to company, from load to load and occasionally from bag to bag.
4. Be extra diligent in your cleaning program.
5. Remember that most operational dilemmas with a pellet stove are usually traced back to
Improper installation, poor quality pellets and/or a lack of timely cleaning.
With just a minimum of daily care your PELPRO pellet appliance will provide years of clean, efficient, comfortable
and environmentally sound heating.
Thank you for selecting a PELPRO wood pellet appliance.
Sincerely,
Canadian Comfort Industries &
Dansons Group Inc.
UPDATES and REGISTRATION
Up to date additions, product information, product registration and warranty extension registration can be found on
our website www.dansons.com/support
COPYRIGHT NOTICE
Copyright 2004, Canadian Comfort Industries. All rights reserved.
No part of this manual may be copied, transmitted, transcribed, stored in a retrieval system, in any form or by any
means without the expressed written permission of,
Canadian Comfort Industries; 26319 Twp Rd 531, Acheson, AB, Canada T7X 5A3

Canadian Comfort Industries V04 3 PELPRO OWNERS MANUAL
Copyright 2004 www.pelprostoves.com Dansons Group Inc.
TABLE OF CONTENTS
INTRODUCTION ------------------------------------------------------------------------------------ 2
TABLE OF CONTENTS ---------------------------------------------------------------------------- 3
SAFETY PRECAUTIONS ------------------------------------------------------------------------- 4,5
SPECIFICATIONS --------------------------------------------------------------------------------- 6
AUTOMATIC SAFETY FEATURES --------------------------------------------------------------
INSTALLATION OPTIONS -----------------------------------------------------------------------
7
8
INSTALLATION CHECK LIST ------------------------------------------------------------------- 9
EXHAUST SYSTEMS ------------------------------------------------------------------------------ 10
GENERAL ---------------------------------------------------------------------------------------- 10
SIZING --------------------------------------------------------------------------------------------- 10
TERMINATION ---------------------------------------------------------------------------------- 11
CLEARANCES ----------------------------------------------------------------------------------- 11
OUTSIDE AIR ---------------------------------------------------------------------------------------- 12
FREESTANDING INSTALLATION -------------------------------------------------------------- 13
STOVE PLACEMENT --------------------------------------------------------------------------- 13
FLOOR PROTECTION ------------------------------------------------------------------------- 13
CLEARANCES ---------------------------------------------------------------------------------- 13,14
ALCOVE ------------------------------------------------------------------------------------------- 14
THROUGH THE WALL DIRECT INSTALLATION ------------------------------------- 15
VERTICAL INSTALLATIONS ---------------------------------------------------------------- 16
MOBILE HOME INSTALLATION ---------------------------------------------------------------- 17
INSERT / BUILT-IN INSTALLATION
IN A WOOD OR COAL BURNING FIREPLACE ---------------------------------------- 18,19
IN A WALL OR MANTEL ---------------------------------------------------------------------- 20,21
OPERATING YOUR STOVE --------------------------------------------------------------------- 22
HOW YOUR PELPRO STOVE WORKS ------------------------------------------------------ 22
LIGHTING A FIRE ---------------------------------------------------------------------------------- 23
THE ACUTRON CONTROLS -------------------------------------------------------------------- 24,25
SHUTTING THE STOVE OFF ------------------------------------------------------------------- 25
PERFORMANCE ENHANCEMENT TIPS ----------------------------------------------------- 26
ACUTRON WALL THERMOSTAT (OPTIONAL) ------------------------------------------- 27
INITIAL BURN SETUP ----------------------------------------------------------------------------- 28
PELLETS
PELLET QUALITY ------------------------------------------------------------------------------ 29
PELLET CONSUMPTION --------------------------------------------------------------------- 29
FACTORS EFFECTING PELLET FEED RATES --------------------------------------- 29
FINE TUNING THE PELLET FEED RATES ---------------------------------------------- 29
ASH and CLINKERS --------------------------------------------------------------------------- 30
FINES --------------------------------------------------------------------------------------------- 30
PFI PELLET STANDARDS ------------------------------------------------------------------- 30
INSERTING, REMOVING, AND ADJUSTING THE BURN GRATE --------------------- 31
REQUIRED CLEANING --------------------------------------------------------------------------- 32
PERIODIC MAINTENANCE ---------------------------------------------------------------------- 33-34
TROUBLE SHOOTING ---------------------------------------------------------------------------- 35
LIMITED WARRANTY -----------------------------------------------------------------------------
APPENDIX “A” - PELPRO OPTIONS -----------------------------------------------------------
36
37
APPENDIX “B” – PELPRO ACCESSORIES ------------------------------------------------- 38,39
SERVICE LOG -------------------------------------------------------------------------------------- 40

Canadian Comfort Industries V04 4 PELPRO OWNERS MANUAL
Copyright 2004 www.pelprostoves.com Dansons Group Inc.
SAFETY PRECAUTIONS
oDo not operate the heater if you smell smoke coming from the heater. Push the “OFF” Touch pad,
monitor your heater, and call your dealer.
oNever use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or
’freshen up’ a fire in this heater. Keep all such liquids well away from the heater while it is in use.
oDon’t unplug the heater if you suspect a malfunction. Push the “OFF” Touch pad and inspect the heater.
oDo not operate the heater if the flame becomes dark & sooty or if the firepot overfills with pellets. Push the
”OFF” Touch pad and periodically inspect the heater (see ”Operating Your Stove”).
oNever try to repair or replace any part of the heater unless instructions for consumer are given in this manual.
All other work should be done by a trained technician.
oThe viewing door and ash pan must be closed and latched during operation.
oNever block free airflow through the open vents of the unit.
oContact your local building officials to obtain a permit and information on any installation restrictions or
inspection requirements in your area. Notify your insurance company of this heater as well.
oThe pellet appliance exhaust system works with negative combustion chamber pressure and a slightly
positive chimney pressure, therefore the exhaust system must be completely airtight and properly installed.
All pellet vent joints must be sealed with HI-TEMP RTV silicone sealant and at least 3 sheet metal screws, to
each other as well as to the heater.
oThis unit must be properly installed to prevent the possibility of a house fire. The instructions must be strictly
adhered to. Do not use makeshift methods, which may compromise the installation.
oYour heater requires periodic maintenance and cleaning (see ”Operating Your Stove”). Failure to maintain
your heater may lead to smoke spillage in your home.
oAllow the heater to cool before carrying out any maintenance or cleaning. Ashes must be disposed in a metal
container with a tight fitting lid. The closed container of ashes should be placed on a non-combustible surface
or on the ground, well away from all combustible materials, pending final disposal.
oThis heater is designed and approved for pelletized wood fuel only. Any other type of fuel burned in this
heater will void the warranty and safety listing.
oThe heater will not operate during a power outage. If a power outage does occur, check the heater for smoke
spillage and open a window if any smoke spills into the room.
oKeep foreign objects out of the hopper.

Canadian Comfort Industries V04 5 PELPRO OWNERS MANUAL
Copyright 2004 www.pelprostoves.com Dansons Group Inc.
SAFETY PRECAUTIONS . . . Continued
oDisconnect the power cord before performing any maintenance. NOTE: Touching the OFF touch pad does not
disconnect all power to the heater.
oDo not throw this manual away. This manual has important operating and maintenance
instructions that you will need at a later time. Always follow the instructions in this manual.
oDo not place clothing or other flammable items on or near the heater. Because this heater can
be controlled by a thermostat there is a possibility of the heater turning on and igniting any
items placed on or near it.
oThis heater must be connected to a standard 110 - 120V., 60 Hz grounded electrical outlet. Do not
use an adapter plug or sever the grounding plug. Do not route the electrical cord underneath,
in front of, or over the heater.
oIt is recommended to connect the heater to a standard 110 – 120V ground surge protected unit or
surge protected electrical outlet..
oWhen installed in a mobile home, the heater must be bolted to the floor, have outside air, and MUST
NOT BE INSTALLED IN THE BEDROOM (Per H.U.D. requirements). Check with local building officials.
oEducate all children on the dangers of a high-temperature heater.
oYoung children should be supervised when they are in the same room as the heater.
oCaution: NEVER PUT FINGERS NEAR AUGER. Pellet fuel is fed to the burn pot by a screw auger that is
driven by a high torque motor. The auger can start and stop automatically anytime while the heater is
operating.
oDo not connect this appliance directly to air ducts or any air distribution system. This will void your warranty.
oDo not burn with insufficient combustion air. A periodic check is recommended to ensure proper combustion
air is admitted to the combustion chamber. Setting the proper combustion air is achieved by adjusting the
slide damper located on the right hand side of the appliance.
oIt is advisable to clean the exhaust vent bi-annually or every two tons of pellets.
oSoot or creosote may accumulate when the stove is operated under incorrect conditions such as an extremely
rich burn (black tipped, lazy orange flames).
Note: Canadian Comfort Industries grants no warranty, implied or stated, for the installation or
maintenance of your heater, and assumes no responsibility of any consequential damage(s).

Canadian Comfort Industries V04 6 PELPRO OWNERS MANUAL
Copyright 2004 www.pelprostoves.com Dansons Group Inc.
SPECIFICATIONS
HEATING SPECIFICATIONS
Approx. Heating capacity (sq. feet) * 800 – 2,000
Approx. Fuel burn rate per hour ** 1.5 – 5 lbs
Hopper Capacity - Traditional Stove / Insert 40 lbs Approx. Burn time at lowest setting 27 hrs
Hopper Capacity – Bay View Free Standing 60 lbs Approx. Burn time at lowest setting 48 hrs
Hopper Capacity – Bay View Insert / Built-In 40-60 lbs Approx. Burn time at lowest setting 27-48
* Heating capacity will vary depending on floor plan layout of your home, degree of insulation, and the outside
temperature. Fuel size, quality, density and moisture level will also have an effect.
** Pellet size may effect the actual rate of fuel feed and burn times. Fuel feed rates may vary by as much as 20%. Use
PFI listed fuel for best results.
DIMENSIONS
ELECTRICAL SPECIFICATIONS
Electrical Rating = 110-120 Volts 60 HZ 2.0 Amps
Watts (operational) = 175 (approximately)
Watts (optional igniter) = 475 (approximately)
A voltage surge protector or ground fault outlet is required for this unit.
EPA COMPLIANCE
This heater is exempt from EPA Phase II requirements, but has been tested for emissions using EPA test methods
by Warnock Hersey , US.
FUEL CONSIDERATIONS
Your Pelpro pellet appliance, is designed to burn pellets that comply with Association of Pellet Fuel Industries
standards. (Minimum of 40lbs density per cubic ft, ¼ to 5/16’ diameter length no greater than 1.5”, not less than
8,200 BTU’s/lb, moisture under 8% by weight, ash under 1% by weight, and salt under 300 parts per million)
Pellets that are soft, contain excessive amounts of loose sawdust, have been or are wet, produce clinkers and/or
heavy ash will result in reduced performance and may actually cause the fire to go out.
24”
28 3/4”
24”
18 3/4”
+
+
Shroud 1
”
+
+
24”
6 1/2”
7 3/4”
8 1/4”
3 ½”
Exhaust
Air I nlet
8 1/4”
Air I nlet
17 1/4”
12 3/4”
6 1/2”
Exhaust
24 3/4
”
24”
24 3/4”
12 1/4” 10 3/4”
+
+
24”
8 1/4”
Air I nlet
17 1/4”
12 3/4”
6 1/2”
Exhaust
24 3/4
”
30”
24”
+
Shroud 1”
8 1/4”
Air In let
17”
12 3/4”
Exhaust
26”
12 1/4” 10 3/4”
+
25”
Air In let
7”
Exhaust
+
+
Exhaust
26”
+
24”
6 ½”
Exhaust
+
Air Inl et 8 1/4”
7 3/4”
3 ½”
24”
Bay View Freestanding Bay View Insert / Built-In
Traditional Freestanding Traditional Insert / Built-In
19”
-
23”
Adjustable
Hopper

Canadian Comfort Industries V04 7 PELPRO OWNERS MANUAL
Copyright 2004 www.pelprostoves.com Dansons Group Inc.
AcuTron Wiring Harness
Air Intake
Vacuum Switch
Low Lim it L1 20
High Limit L250
Fan Limit F140
Combustion Fan
Exhaust
AUTOMATIC SAFETY FEATURES
L250 HIGH LIMIT SWITCH
Your pellet appliance has a high temperature limit switch installed. If the temperature at the back of the firebox
reaches approximately 250deg F., the switch will shut off the electricity going to the Vacuum Switch and to the
Auger Motor. The auger will automatically stop, and the appliance will shut down when the exhaust temperature
cools (120deg F). If this happens call your dealer or Dansons Customer Service (1-866-456-9269).
IT IS IMPORTANT TO FIND THE REASON WHY THE UNIT OVERHEATED.
L120 LOW LIMIT SWITCH
This limit switch is mounted on the exhaust blower housing and has 2 main functions.
1. Should the fire happen to go out, for any reason, this limit switch will shut the stove off when the exhaust
temperature drops below 120deg F.
2. Upon starting the appliance, the AcuTron control board has a 15 minute “Lighting Mode”, if the stove
exhaust does not reach 120deg F in that 15 minutes the stove will shut off. As soon as the stove exhaust
does reach 120deg F, the limit switch opens and the AcuTron enters a 5 minute “Safety Delay” mode.
F140 FAN LIMIT SWITCH
Your pellet appliance has a convection fan control limit switch. The room air fan's (F140) temperature limit snap
switch automatically sets the fan on high when your stove is producing heat faster than the fan is carrying it into the
room. This may occur when the heat control lever is set at [3 or 4] and the FAN SPEED is set to a very low or off
setting. After the fan runs at this
automatic high setting a few minutes,
it may cycle back to its lower setting
and may continue to cycle between
[HIGH] and your selected setting.
The circulation (room air) fan cycling
from high to low is a normal condition
as well as a safety feature of your
appliance. To compensate for the fan
cycling, adjust the FAN SPEED to a
higher setting.
VACUUM SWITCH
This safety device (mounted on the
back panel pillar) detects vacuum in
the exhaust system, firebox, and air
intake. If the exhaust blower fails, the
vent pipe becomes plugged, the
viewing door is open, or if you are out
of pellets, this switch will sense that
there is no airflow and will stop the
auger from continuing to feed pellets.
If the power does go out, the pellet appliance will stop running. When the power comes back on,
the stove will not restart if the switch is in the manual mode. If the exhaust temperature is above
120deg F or the switch is in the manual position, the stove will start to feed pellets again and may
re-light itself.
NOTE: If power outages are a concern you may wish to purchase a battery back-up system. It must state “For
Igniter Equipped Appliance” and be a minimum of 750 watts.
For further information contact your local Specialty Retailer, Certified HVAC Service Depot, or Dansons
Group Inc. Customer Service Department at 1-866-456-9269.

Canadian Comfort Industries V04 8 PELPRO OWNERS MANUAL
Copyright 2004 www.pelprostoves.com Dansons Group Inc.
FPP
Bay View Freestanding
IPP
Bay View Insert / Built-In
FPP
Freestanding
IPP
Insert / Built-In
Figure 1 Figure 2
Figure 4
Figure 3
INSTALLATION OPTIONS
READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE YOUR
PELPRO HEATER. FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN
PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH!
(See specific Installation details for clearances and other installation requirements)
The two PELPRO models are the: “FPP” Freestanding: a Traditional styled stove (figure 1), and a Bay View
style(figure 2); and the “IPP” Fireplace Insert / Built-In: a Traditional style (figure 3), and a Bay View style (figure
4). Both models come with either black painted or brass trimmed doors.
All models may be installed to code in both conventional and mobile homes.
INSTALLATION OPTIONS INCLUDE:
1. A FREESTANDING STOVE: Set on a pedestal and placed on a non-combustible floor pad. (figure 1 &2)
2. An ALCOVE: Set on a pedestal and placed on a non-combustible floor pad in compliance with clearance
requirements for an installation in an alcove. (figure 1 & 2)
3. A HEARTH STOVE: When installed with or without a pedestal on a non-combustible hearth of a masonry or
factory built wood or coal burning fireplace. (figure 1 & 2)
4. AFIREPLACE INSERT: When installed, with a shroud, in a masonry or a factory built, wood or coal burning
fireplace. (figure 3 & 4)
5. A BUILT-IN INSERT:When installed on a non-combustible pad, in a wall or custom built mantel and where
adequate airflow around the stove is provided. (figure 3 & 4)

Canadian Comfort Industries V04 9 PELPRO OWNERS MANUAL
Copyright 2004 www.pelprostoves.com Dansons Group Inc.
Window
Burn Pot
Burn Grate
Heat Tubes
Tube Scraper
E Z Clean
Grate
Hopper
Fan Motors
Auger
Exhaust
A
ir Intake
Auger Motor
Ash Pan
INSTALLATION CHECK LIST
Unless you are knowledgeable and experienced in stove installation, we recommend your PELPRO stove
receive a Pre-delivery Check and be installed by your local Specialty Retailer or Certified HVAC Service
Depot.
COMPLETE THIS CHECK LIST PRIOR TO LIGHTING YOUR FIRST FIRE:
_____ Carefully read this "Owner's Manual”. SAVE THIS MANUAL.
_____ Obtain final inspection and approval by local building officials.
_____ Carefully clean all marks off the brass parts before the first fire is lit. Use a soft cloth and a gentle type
cleaner. Caution: Never use an abrasive cleaner on any part of your stove.
_____ Polish the hopper to remove the oil type coating used in manufacturing.
_____ Have your local Dealer demonstrate all the operational, cleaning and maintenance steps necessary
for your stove.
_____ Sign and keep a copy of the Pre-delivery Check List supplied by your Authorized Pelpro Dealer,
“Dansons Certified Installer”, found inside our appliance or available online.
Register online at www.dansons.com/support for Extended Warranty.
______ Register your purchase online at www.dansons.com/support.
_____ Fill the hopper with quality pellets to prime the unit; Using the CCI “AcuTron”, (figure 5), PUSH the
FEED RATE Touch Pad and this will start the auger and the combustion fan.
NOTE: Do not attempt to light a fire at this time. Leave the START / FEED RATE [ON] for 2 to 5 minutes until
pellets start dropping into the burn grate. Then touch the OFF pad to turn off system . The auger is now primed to
deliver fuel to the burn grate (figure 6). Then light the stove according to the directions outlined in "LIGHTING
YOUR STOVE",
CCI –“AcuTron Board” Cutaway View
Figure 3 Figure 4

Canadian Comfort Industries V04 10 PELPRO OWNERS MANUAL
Copyright 2004 www.pelprostoves.com Dansons Group Inc.
EXHAUST SYSTEMS (GENERAL)
PELLET VENT MUST MAINTAIN A MINIMUM 3” CLEARANCE TO ANY COMBUSTIBLE
(INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER).
DO NOT CONNECT THE PELLET VENT TO A VENT SERVING ANY OTHER APPLIANCE
OR STOVE.
DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT.
PELLET VENT TYPE:
Must be an approved 3” or 4” Diameter Type ”PL” vent, vented to the outside (fig. 7) or connect the vent to a
factory built type “A” chimney using an adaptor; and/or “All Fuel” Stainless Steel chimney liner for masonry
fireplace installations (fig. 8) . Use 4” dia. vent if vent or liner height is over 15’ or if installation is over 4,000’
above sea level.
MAXIMUM VENTING SIZE:
VENT INSTALLATION:
Termination must exhaust above the air inlet elevation, and parallel or above the exhaust output of the
pellet appliance. It is recommended that at least 3’ of vertical pipe be installed to create some natural
draft. This is to help prevent the possibility of smoke or odor during the appliance shut down.
Horizontal sections must have a ¼” rise every 12” of travel after 3’ long.
Pellet Vent connections must be sealed with HI-Temp RTV Silicone and screwed together with at
least 3 x 3/8” long stainless steel screws. Seal each vent section by injecting a liberal amount of HI-
TEMP RTV silicone sealant into the gap.
Use Diameter “PL” Vent
If venting outside of
shaded area.
4”
0’
0’
5’
5’
10’
10’
15’
20’
25’
30’
33’
Vent must have a support
bracket every 5’ when on
the exterior wall.
If appliance is installed
above 4,000’ elevation,
always use 4” diameter
venting.
Vent height and run
exceed the distance
shown in the un-shaded
region of chart.
must
not
To achieve optimum
performance, keep vent runs
as short as possible.
Especially on horizontal
installations.
Use or Diameter
“PL” Vent, if venting in
shaded area.
3” 4”
Maximum venting height is 33’.
Maximum horizontal offset is 10’.
Use no more than 180 of elbows
(two 90 elbows, or two 45 elbows
& one 90 elbow, etc), plus
termination.

Canadian Comfort Industries V04 11 PELPRO OWNERS MANUAL
Copyright 2004 www.pelprostoves.com Dansons Group Inc.
EXHAUST SYSTEMS . . . Continued
PELLET VENT TERMINATION: (Figures 7 & 8)
Termination must be a minimum of 6” above the chimney (B) (note: the chimney must meet local
codes for height above the roof or other obstructions)
Must have an approved cap (to prevent water from entering) or a 45* elbow downturn
If the termination is located on a windy side of house, an approved house shield is recommended to
prevent soot from accumulating on the side of the house.
Must not be located where snow or other materials will plug it.
Must have a “Metal Seal Plate” or “Wall Thimble” at point (A)
Figure 7 Figure 8
VENT TERMINATION CLEARANCES:
•Horizontal terminations must protrude 12” from the wall, vertical terminations 24”
Figure 9
A Minimum 4’ clearance below or beside any door or window which opens.
B Minimum 1’ clearance above any door or window that opens.
C Minimum 3’ clearance from any adjacent building.
D Minimum 7’ clearance above any grade when adjacent to public walkways.
NOTE: Vent may not terminate in covered walkway or breezeway.
E Minimum 2’ clearance above any grass, plants, or other combustible material.
F Minimum 3’ clearance from any forced air intake of any other appliance.
G Minimum 2’ clearance below eves or overhang.
H Minimum 1’ clearance horizontally from combustible wall.
X Must be a minimum of 36” above the roof and 24” above the highest point of the roof within 10’.
A
B
3’
10’
2’
x
A
AF
G
4
12”

Canadian Comfort Industries V04 12 PELPRO OWNERS MANUAL
Copyright 2004 www.pelprostoves.com Dansons Group Inc.
OUTSIDE AIR
Outside air is REQUIRED ON ALL MOBILE HOME INSTALLATIONS.
Outside air is strongly recommended for all other installations. Failure to install intake air may result
in improper combustion as well as the unit smoking during power failures.
Metal pipe, ONLY, either solid or flexible, must be used in all outside air installations.(B)
NOTE: Non-metallic material MUST NOT BE USED for outside air installations.
A wind shield, (C), over the termination of the outside air pipe or a 90 degree elbow or bend directed
away from the prevailing winds MUST be used when an outside air pipe is installed through the side
of a building. Keep the outside air pipe termination at least 1 foot away from the exhaust system
termination.
When outside air is taken from an existing chimney the exhaust system must not terminate in the
same chimney.
The outside air pipe on your stove is 2" OD. The outside air connecting pipe must be at least 2" ID
The outside air connecting pipe must be as short and free of elbows as possible, and must fit over,
(A), not inside, the outside air pipe on your stove.
Through The Wall Kits Include:
3FOOT PACKAGE –PART#ACFAKT3 10 FOOT PACKAGE –PART#ACFAKT10
1 – 2” Galvanized Hood c/w screen 1 – 2” Galvanized Hood c/w screen
1 – 2” Aluminum Flex Duct – 1 – 2” Aluminum Flex Duct –
compressed 15” length, extends to 30” – 36” compressed 4’ length, extends to 120”
2 – 2” Worm Gear Clamps 2 – 2” Worm Gear Clamps
NOTE: Available from your local Authorized Dealer or Dansons Group Inc. 1-877-303-3134
Figure 9

Canadian Comfort Industries V04 13 PELPRO OWNERS MANUAL
Copyright 2004 www.pelprostoves.com Dansons Group Inc.
FREESTANDING STOVE INSTALLATION
STOVE PLACEMENT:
Stove must be placed so that no combustibles are within, or can swing within (i.e. drapes doors),
36” of the heater.
If the stove is placed in a location where the ceiling height is less than 7’, it must follow the
requirements in the section “Alcove Installation”.
Stove and floor protection must be installed on a level secure floor
FLOOR PROTECTION REQUIREMENTS:
The stove must be installed on a non-combustible floor protector (i.e. sheet steel with cement, tile or
slate) extending the full width and depth of the stove and extending 6” in front of the stove. Floor
protector needs to be a minimum of 24.5” deep X 30.5” wide and must be a minimum of .018” thick
(26 gauge).
Must extend under and 2” to each side of chimney tee (if used).
MINIMUM CLEARANCES TO COMBUSTIBLES (FIGURES 10 – 15)
1” From Back Of Heater To Combustibles 3” From PL Vent to Combustibles
2” From Side of Heater to Combustibles
1” From Back Corner of Heater to Combustibles 6” Non Combustible Surface In Front Of Heater
16” From Top Of Heater to Combustibles 36” to drapes, doors, anything that can swing
CLEARANCES – “STRAIGHT INSTALLATION”:
Figure 10 Figure 11
6”
1”
10”
6”
1”
2”
12”
HROUGH HE ALL T T
W
6”
3”
2”
NTERIOR ERTICAL I V

Canadian Comfort Industries V04 14 PELPRO OWNERS MANUAL
Copyright 2004 www.pelprostoves.com Dansons Group Inc.
FREESTANDING INSTALLATION . . . continued
CLEARANCES – “CORNER INSTALLATION”:
Figure 12 Figure 13
Note: If interior vertical vent is used, the clearance to the back wall is determined by the upward-turned
elbow or “Tee”. It will vary in depth depending on the brand of PL vent used.
Before placing the stove, connect the elbow or “Tee” and measure off the 3” clearance.
ALCOVE INSTALLATION:
Minimum clearances to combustibles for a stove. (Figures 14 and 15)
1 inch from the back
16 inches from the top
6 inches from the sides
30 inches deep
Figure 14 Figure 15
1”
2”
12”
6”
HROUGH HE ALL T TW
ORNER 45 C
3”
6”
2”
NTERIOR
ERTICAL
I
V
ORNER 45 C
1”
16”
6”
1”
10”
6”
1”
6”
12”
6”
LCOVE HROUGH HE ALL A -T TW

Canadian Comfort Industries V04 15 PELPRO OWNERS MANUAL
Copyright 2004 www.pelprostoves.com Dansons Group Inc.
A
B
A
C
D
EF
G
H
J
4
FREESTANDING INSTALLATION . . . continued
Figure 16
NOTE: Some horizontal, through the wall installations may require a Clean-Out Tee and a minimum 3’ vertical rise
of pipe outside the building to help draft the stove. This is required if a proper burn cannot be maintained, after the
stove has been tested and the airflow set. This is due to backpressure in the exhaust, caused by the airflow around
the house.
THROUGH THE WALL, DIRECT INSTALLATION. (Figure 16)
1. Select the location for your stove, design the exhaust system and determine the brand and size of "PL" vent to
be used.
2. Position the floor pad, (C).
3. Following the "PL" vent manufacturer's specifications, mark and cut a hole through the wall to accommodate the
wall thimble, (A), and the outside air pipe, (B), if outside air is to be used. Install the wall thimble, (A). Be sure to
run a bead of silicone around the outside edges of the wall thimble to reduce drafts. Insert the proper size of
"PL" vent, (D), through the wall thimble, (A). Place your stove on the floor pad, (C), close to its final position.
Leave room to connect the "PL" vent to your stove. Place a bead of RTV silicone around the end of your stove's
exhaust pipe, (E). Connect the “PL” vent pipe adaptor (J) onto the stoves exhaust pipe. Connect the length of
"PL" vent, (D), that is in the thimble, (A), onto the pipe adaptor (E). Fasten together with at least three sheet
metal screws (approx. ½” in length). Place a bead of RTV silicone around the connection. Place your stove in its
final position on the pad. Place another bead of RTV silicone around the “PL” vent and the inside of the wall
thimble, to stop cold air drafts.
4. Note: If 4" PL vent is required, use an increaser, (J), on the stove exhaust pipe.
5. On the outside of the building, place a 45 degree "PL" type elbow, (F), onto the end of the horizontal "PL" vent,
(D). Optionally, place a rodent screen cap, (G), (may be required in some locals), on the end of the elbow, (F).
Secure all connections using 3 sheet metal screws and run a bead of RTV silicone around all connections. Also
run a bead of RTV silicone around the “PL” vent pipe and the outside of the wall thimble.
6. If outside air is used, install the outside air pipe, (B). Seal the outside air pipe, (B), to your stove's outside air
pipe, (I), with RTV silicone. Make sure the outside air pipe fits over, (not inside), your stove's outside air pipe.
Install a wind shield (H). Run a bead of silicone around the inside and outside walls, again to reduce cold drafts.
A PL Wall Thimble
B Outside Air Intake
C Hearth Pad
D PL Vent Length
E Stove Exhaust
F PL 45 deg elbow
G PL Screened End Cap
H Fresh Air Hood
I Combustion Air Intake
J PL Pipe Adaptor
6”
1”
10”
6”
1”
2”
12”

Canadian Comfort Industries V04 16 PELPRO OWNERS MANUAL
Copyright 2004 www.pelprostoves.com Dansons Group Inc.
16”
FREESTANDING INSTALLATION . . . continued
VERTICAL INSTALLATIONS: (Figures 17 - 22)
Your stove may be installed using many different vertical designs. Follow the same basic steps in locating
your stove, attaching the exhaust system and outside air intake to your stove as described in
"FREESTANDING INSTALLATION" and the "PL" vent manufacturer's procedures for installing through a
wall, ceiling, eve and roof.
COMMON, (but not inclusive), VERTICAL INSTALLATION DESIGNS ARE:
VERTICAL, THROUGH THE CEILING, through another room, space or attic, then through the roof,
terminating with a rain cap. Figure 17.
VERTICAL, UP TO AN EXISTING CLASS A CHIMNEY OR MASONRY CHIMNEY. An appropriately
sized adapter will be needed when connecting onto either a Class A chimney or into a masonry chimney.
NOTE: The connection into a masonry chimney must be airtight. Figures 18,19 and 21.
HORIZONTAL, OUT THE WALL, THEN VERTICAL to a minimum of 5 feet, into a 90-degree elbow and
terminating with a 45-degree elbow pointed downward. Figure 20.
HORIZONTAL, OUT THE WALL, THEN VERTICAL THROUGH THE EVES AND ROOF, terminating
with a rain cap. Figure 22.
Figure 17 Figure 18 Figure 19
Figure 20 Figure 21 Figure 22
A
B

Canadian Comfort Industries V04 17 PELPRO OWNERS MANUAL
Copyright 2004 www.pelprostoves.com Dansons Group Inc.
MOBILE HOME INSTALLATION
CAUTION: DO NOT INSTALL STOVE IN SLEEPING ROOM
THE STRUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR,
CEILING/ROOF MUST BE MAINTAINED!
Your PELPRO stove has been tested and listed for mobile home installation. It may be installed in a mobile
home as a "Free Standing Stove", a "Hearth Stove", or as an "In Insert" installed in an existing wood or coal-
burning fireplace or as an "Built –In Insert" installed with a mantel.
In addition to all previously detailed installation requirements, mobile home installations
must meet the following requirements:
Permanently bolt your stove to the floor, (A). Figure 23, 24
Electrically ground your stove or the pedestal to the steel frame of the home. Use a number 8 gauge copper
wire, (B) figure 24, or equivalent.
The stove must have a permanent outside air source with a ¼ inch screen over the inlet.
Figure 23, (B,C, D)
For transportation all chimney / vent above the mobile home must be removed.
“PL” Vent must be 3” or 4” PL Vent and must extend a minimum or 36” above the roofline of the
mobile home and must be installed using a UL/ULC listed ceiling fire stop (J), figure 23, and
rain cap (L), figure 23.
INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER.
A Floor Pad
B Combustion Air Intake
C Fresh Air Duct
D Fresh Air Hood
E Stove Exhaust
F Pipe Adapter
G Clean Out Tee
H Tee Support Bracket
I Pipe
J Firestop Spacer / Ceiling Support
K Roof Flashing / Storm Collar
L Rain Cap
Figure 23 Figure 24
Note: When moving your Mobile Home, all exterior venting must be removed while Mobile Home is
being relocated. Upon completion of relocation all venting must be reinstalled and securely fastened.
B
A
CD
G
H
I
J
K
L
FRAME
HEARTH PAD
FLOOR
B
GROUND
WIRE
A
BOLT(S)

Canadian Comfort Industries V04 18 PELPRO OWNERS MANUAL
Copyright 2004 www.pelprostoves.com Dansons Group Inc.
FIREPLACE INSERT INSTALLATION
VENTING INTO AN EXISTING CHIMNEY:
CAUTION:
MAKE SURE THE CHIMNEY AND FIREBOX ARE CLEAN AND FREE OF SOOT AND ASHES BEFORE
INSTALLATION BEGINS. FAILURE TO DO SO MAY RESULT IN THE TRANSFER OF SOOT INTO THE ROOM
BY WAY OF THE CONVECTION FAN.
The PELPRO Insert may be installed in a masonry or factory built fireplace as shown in Figure 25 & 26
INSTALLING SOLID-FUEL INSERTS INTO FACTORY BUILT FIREPLACES:
The insert must be tested and meet the requirements of UL 1482 (U.S.) and or ULC 8628 (Canada) when
tested in a masonry fireplace built per ULC S628.
The factory-built fireplace must be listed per UL 127 or ULC 8610.
Clearances obtained from the masonry fireplace tests are also relevant for installation in factory-built
fireplaces.
Installation must include a full height listed chimney liner meeting type HT requirements (2100 degree F.)
per UL 1777 (U.S.) or ULC 8635 (Canada). The stainless steel liner must be securely attached to the
insert flue collar and the chimney top.
Means must be provided to prevent room air passage to the chimney cavity of the fireplace. This may be
accomplished by sealing the damper area around the chimney liner, or sealing the fireplace front.
The airflow within and around the fireplace shall not be altered by the installation of the insert (i.e. no
louvers or outlet ports are blocked), unless specifically tested as such for each factory-built fireplace
manufacturer and model line. (Note - using a louvered faceplate (surround) complies with this
requirement).
Alteration of the fireplace in any manner is not permitted with the following exceptions;
1. External trim pieces which do not affect the operation of the fireplace may be removed providing
they can be stored on or within the fireplace for re-assembly if the insert is removed.
2. The chimney damper may be removed to install the chimney liner.
Circulating air chambers (i.e. in a steel fireplace liner or metal heat circulator) shall not be blocked.
Means must be provided for removal of the insert to clean the chimney flue.
Inserts that project in front of the fireplace must be supplied with appropriate supporting means.
A permanent metal warning label must be attached to the back of the fireplace stating
that the fireplace must be restored to its original condition for safe use with out the insert. This sticker is
supplied in the packaging for the insert shroud.
(See Following statement)
THIS FIREPLACE HAS BEEN ALTERED TO ACCOMMODATE
A FIREPLACE INSERT AND SHOULD BE INSPECTED BY A
QUALIFIED PERSON PRIOR TO RE-USE AS A CONVENTIONAL FIREPLACE!

Canadian Comfort Industries V04 19 PELPRO OWNERS MANUAL
Copyright 2004 www.pelprostoves.com Dansons Group Inc.
FIREPLACE INSERT INSTALLATION …CONTINUED
When installing into a masonry chimney, it is recommended that the exhaust vent be extended to the top of
the chimney as shown to the lower right. However, if the vent pipe does not extend to the top of the
chimney, the pipe must extend a minimum of 18” above the damper.
You must seal the damper area with a steel plate when using the direct connection method.
The Vent Pipe Must Extend Above The Damper into the first tile of the flue liner (Figure 25) in the USA and
to the top of the chimney CANADA (Figure 26). The chimney must not be corroded or damaged in any way
for this type of installation to be permitted. A direct vent may be made through the chimney structure if local
codes permit.
Figure 25 Figure 26
Metal
Sealing Plate
18” min.
length
18”18”18”
8”
Note: This installation allowed in Canadanot
DIRECT CONNECTIO
N
6”
Liner Support
Deluxe Cap
Optional
Metal Plate
6”
18”
8”
FULL CHIMNEY RELINE
Note: This installation recommended
for all chimney installations!
is

Canadian Comfort Industries V04 20 PELPRO OWNERS MANUAL
Copyright 2004 www.pelprostoves.com Dansons Group Inc.
4
18”
8”
6”
Wood Frame
Construction
Stand Offs
Part ACI-3HZ
6”
2” Min.
Air gap
Horizontal Vent Installation
Exterior Wall
Wood Surround
Shroud
3” minimum
air gap
Wall Band /
Support Brkt
every 5’
Clean Out Tee
10’
2’
BUILT-IN INSERT INSTALLATION
CAUTION: DO NOT BLOCK VENT OPENING
The PELPRO Insert may be framed directly into a wall as either a horizontal or vertical vent installation see (figure
27, 28). The exhaust installation requirements are the same as for a freestanding stove. Refer to “Installing your
Freestanding Stove” for information concerning installation and proper hook-up of the exhaust.
NOTE: Built-In Installations require Enclosure Kit #ACI-3HZ Horizontal Vent or #ACI-3VL Vertical Vent.
Dimensions that will be enclosed within the frame work are:
This example shows the
exhaust venting out and
up vertically
Requires Spacer Kit
#ACI-3HZ
The framed opening for this
Installation needs to be:
Tradition Bay View
Height 21” 21 - 25”
Width 30” 30”
Depth 17” 17”
If constructing a chase, adequate
Insulation, vapor barrier, drywall,
And caulking must be used.
FIGURE 27
24”
18 3/4”
Shroud 1”
+
+
6 1/2”
7 3/4”
8 1/4”
3 ½”
Exhaust
Air Inlet
24”
24 3/4”
12 1/4” 10 3/4”
Traditional Insert / Built-In
24”
19”
-
23”
Shroud 1”
12 1/4” 10 3/4”
+
Exhaust
26”
+
24”
6 ½”
Exhaust
+
Ai r Inl et 8 1/4”
7 3/4”
3 ½”
Bay View Insert / Built-In
Adjustable
Hopper