Pensonic PSF-18 User manual

STAND FAN
PSF-18
INSTRUCTION
MANUAL

CONTENTS
Title Page No.
Parts Introduction 1
Technical Specifications 1
Before Using 2
How to Assemble Stand Fan 2
How to Use Stand Fan 2
Cleaning and Maintenance 3
Important Guidelines 3
Thank you for choosing PENSONIC appliances. May you have an enjoyable experience using our
products.

Parts Introduction
1. Locking Screw
2. Front Guard
3. Guard Clip
4. Guard Ring
5. Blade Knob
6. Fan Blade
7. Guard Interlocking Nut
8. Rear Guard
9. Speed Button Selector
10. Rotor Pin
11. Motor Shaft
12. Front Motor Cover
13. Oscillation Knob
14. Rear Motor Cover
15. Panel Screw
16. Extension Tube
17. Height Adjustor Knob
18. Stand
19. Base
20. Molded Securing Knob
Technical Specifications
Voltage
220-240V~
Wattage
70W
Frequency
50Hz
Blade Size
18” (450mm)
1 2 3 4 5 6 7 8
12
11
10
9
15
16
17
18
13
14
19
20

Before Using
Please read these instructions carefully before use and keep them for future reference.
Check your local main voltage whether it is the same as stated on the appliance.
Before using for the first time, remove any protective films or stickers from the table fan.
Ensure the power switch is at the off position.
How to Assemble Stand Fan
Attach the rear guard to the front side of the motor; fasten the guard interlocking nut by turning
it clockwise until the guard is secured firmly in place.
Mount the fan blade onto the motor shaft; fasten the blade knob by turning anti-clockwise
firmly.
Installing the front guard:
- Open the front guard clip and attach the hook to the rear guard.
- Push the round edges of front guard to fit it securely into the rear guard.
- Lock the clip.
Installing the base:
- Insert the stand body to the base unit firmly. Reverse the whole unit and secure the stand
body by fitting the molded securing knob from the bottom of the base unit.
- Connect and fix the fan body to the stand body.
- Ensure the stand is COMPLETELY interlocked with the base unit.
- Insert the panel to the stand body and lock it into position by turning the panel screw
clockwise. Loosen the height adjustment knob to extend the extension tube to the required
height and then tighten the securing knob.
How to Use Stand Fan
Connect the plug into a power supply socket and switch on the power.
Switch on the fan by turning the speed button at any of the “3”, “2” or “1” settings.
Turn the “3”, “2” or “1” button to adjust the fan speed from High-Medium-Low.
To stop the fans, turn the speed knob to the “OFF” position.
To tilt the fan, always ensure that the fan is at „OFF‟ position and wait until the blade has
completely stopped for safety reasons. Hold the stand firmly with one hand and move the guard
gently upwards or downwards.
The oscillation knob is positioned at the top of the rear motor. Press the knob down to make the
fan oscillate and pull it up to stop the oscillation.
To adjust the height of fan, always ensure that the fan is at off position and wait until the blade
has completely stopped for safety reason. Hold the stand firmly and loosen the height adjust
knob, then push up or pull down the extension tube to adjust the fan height.

Cleaning and Maintenance
Always unplug the product from the wall socket and shut down completely prior to cleaning.
Do not use abrasive sponge, scouring pads or stiff brush to clean the appliance.
Please be cautious when cleaning the product near to the motor housing area.
Use only damp cloth to wipe the exterior surfaces of the unit. Do not immerse the main body in
water.
Do not allow the motor or other electrical components to be exposed to water.
For proper storage, always place the fan in a low humidity environment.
Important Guidelines
Use only original accessories supplied.
The current voltage which indicates on the plate must correspond to your local voltage.
The stand fan should be operated only on condition that the type of power supply corresponds to the
marking label. Otherwise, it willnot work or even be damaged.
Never operate unit unless it is fullyassembled.
Do not overload outlets or extension cords. It can result in fire or electric shock.
Do not operate the appliance if the power supply cord or plug has been damaged.
This fan is intended for indoor and household use only; not for outdoor, commercial and
industrial use.
Do not immerse the cord, plug or appliance in water or other types of liquid and do not pour
water onto it to avoid from fire, electrical shock or personal injury.
To protect against risk of electrical shock, do not force any foreign objects such as pins and
wires into any openings.
Do not pull the cord to remove the plug from wall socket, pull on the plug instead.
Do not attempt to insert or remove the plug with wet hands.
Do not place the appliance on or near hot gas/electric burner, or a heated oven.
Do not let cord hang over the edge of table or counter or touch any hot surfaces.
In the event not using the appliance for a long period of time, please remove the plug from the
power outlet.
Do not allow the motor or other electrical components to be exposed to water.
Never let children use electrical equipment without adult supervision.
Educate children about the danger and safety rules associated with operating electrical
equipment.
This appliance should not be used by the physically challenged, slow response or mentally
disabled people (including children) unless guidance is provided during operation.
Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions
or has been damaged in any manner. Repair and services should always be carried out by
PENSONIC Customer Care/Service Centre.