Perenio PEIRC01 User manual

Installation and Operation Manual
for Perenio® PEIRC01
Indoor Motor Camera
July, 2021

Installation and Operation Manual for
Perenio® PEIRC01 Indoor Motor Camera
©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.6.1
Page 3of 48
Introduction
Perenio® Cameras are specially designed for indoor monitoring. They are used as
part of the Perenio Smart Building Management System for the purpose of video
surveillance and recording.
Such Cameras allow Users to control and hear everything happening in the area of
interest. A high-quality (Full HD) video can be maintained under poor lighting
conditions which makes sense for video recording and imaging at night.
The present Manual contains a detailed description of the device, as well as instructions
for its installation and operation.
Copyrights
Copyright of ©Perenio IoT spol s r.o. All rights reserved.
The Perenio® trademark is owned by Perenio IoT spol s r.o. (hereinafter referred to
as the Perenio IoT). All other similar trademarks and names, as well as logos and other
symbols are the property of their respective owners*.
All materials under Perenio® tradename contained therein are protected in
accordance with international and local laws including Acts on copyrights and related
rights.
Any reproduction, copying, publication, as well as further distribution or public display
of materials contained in the present document (whether in full or in part) shall not be
allowed until an appropriate permission of the copyright owner is obtained. Any
unauthorized usage of materials contained herein may lead to civil liability and criminal
prosecution in accordance with applicable laws.
Any eventual mentioning of other company names and equipment in the present
document is made solely for the purpose of clarifying and describing the device
operation and shall not infringe on the third party’s intellectual property rights.
*ZIGBEE is the registered trademark of ZigBee Alliance; iOS is the registered trademark of CISCO TECHNOLOGY, INC.;
Android is the registered trademark of Google Inc.; Google Play is the trademark of Google Inc.; App Store is the
registered trademark of Apple Inc.; Linux is the registered trademark of Linus Torvalds.

Installation and Operation Manual for
Perenio® PEIRC01 Indoor Motor Camera
Doc Version: 2.6.1 ©Perenio IoT spol s r.o. All Rights Reserved
Page 4of 48
Responsibility and Technical Support
The present document is prepared in accordance with all necessary requirements and
contains detailed information on the device installation, configuration and control valid
as of the date of its issue.
Perenio IoT reserves the right to modify the device and make corrections or changes
to this document without prior notice of the User, and shall not be responsible for any
potential negative consequences which may arise from the use of an outdated version
of the document, as well as for any possible technical and/or typographical errors,
either omitted or accidental, or any related damage that may result from the document
transfer or the use of devices.
Perenio IoT shall make no guarantee with respect to any data contained herein
including but not limited to the device merchantability and fitness for a particular
purpose.
In case of any discrepancies between language versions of this document, the Russian
version of this User Manual shall prevail.
For any technical issues, please contact your local Perenio IoT representative or the
Tech Support Department at perenio.com.
The most common problems may be found in Section 7 of the present document and
at perenio.com where you can also download the latest version of this Installation
and Operation Manual.
Manufacturer:
Perenio IoT spol s r.o.
Na Dlouhem 79, Ricany –Jazlovice 251 01, Czech Republic
perenio.com

Installation and Operation Manual for
Perenio® PEIRC01 Indoor Motor Camera
©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.6.1
Page 5of 48
Conformance to Standards
The device is CE certified and complies with requirements of the
following Directives of the European Union:
2014/53/EU Radio Equipment Directive (RED);
2014/35/EU Low Voltage Directive;
2004/30/EC Electromagnetic Compatibility Directive.
The device complies with the UKCA marking requirements for
selling the device in the UK
The device has passed all procedures of assessments established
in Technical Regulations of the Customs Union and conforms with
standards of the Customs Union
The device complies with the requirements of Restriction of the Use
of Certain Hazardous Substances in Electronic and Electrical
Equipment (2011/65/EU Directive)
The device complies with requirements of the Technical Regulations
of the Republic of Belarus TR 2018/024/BY (Telecommunications.
Security)
The external power source complies with STB 2463-2020 where
requirements for the environmental design of external power
sources in the area of average effective efficiency and power
consumption in idle mode are established
The national conformity mark of the Ukraine indicating that the
device meets requirements of all applicable technical regulations
The crossed-out trash can symbol is used to label electrical and
electronic equipment, and indicates its separate collection.
The symbol is given in accordance with the Directive 2012/19/EU
on Waste Electrical and Electronic Equipment (WEEE)* and
indicates that this equipment requires separate collection at the
end of its life and must be disposed of separately from unsorted
household waste.

Installation and Operation Manual for
Perenio® PEIRC01 Indoor Motor Camera
Doc Version: 2.6.1 ©Perenio IoT spol s r.o. All Rights Reserved
Page 6of 48
To protect the environment and human health, please dispose of
used electrical and electronic equipment according to approved
safe disposal guidelines
Details on available Certificates are specified in
Section 6 of the present document. For copies
of Certificates and Reports, please visit a
corresponding Section at perenio.com.
BG
CZ
DE
ES
FR
GR
IT
KZ
LT
LV
NL
NO
PL
RO
RU
SE
SK
TR
UA
UK

Installation and Operation Manual for
Perenio® PEIRC01 Indoor Motor Camera
©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.6.1
Page 7of 48
Table of Contents
Introduction ..................................................................................................... 3
Copyrights ....................................................................................................... 3
Responsibility and Technical Support................................................................... 4
Conformance to Standards................................................................................. 5
Table of Contents.............................................................................................. 7
1 General Description and Specifications ............................................................. 9
1.1 General Purpose ....................................................................................... 9
1.2 Technical Specification ............................................................................ 12
1.3 Scope of Delivery.................................................................................... 15
1.4 Packaging and Labelling .......................................................................... 16
1.5 Safe Operation Rules .............................................................................. 16
1.6 The Use of Power Adapters ...................................................................... 17
2 Installation and Setup................................................................................... 20
2.1 First Installation and Configuration ........................................................... 21
2.2 Camera Control Panel ............................................................................. 28
2.2.1 Armed Mode ..................................................................................... 29
2.2.2 Event History.................................................................................... 30
2.2.3 Presets............................................................................................. 30
2.2.4 Viewing Saved Videos........................................................................ 31
2.2.5 Additional Settings ............................................................................ 32
2.2.6 Subscriptions.................................................................................... 34
2.3 Upgrading the Camera Firmware .............................................................. 36
2.4 Reset to Factory Settings......................................................................... 36
2.5 Camera Rotation..................................................................................... 37
2.6 Ethernet Connection ............................................................................... 37
2.7 Wi-Fi Router Frequency Settings .............................................................. 37
2.8 The Use of MicroSD................................................................................. 38
2.9 Using the Camera Mic ............................................................................. 39
2.10 Changing the Room or Location for Cameras............................................ 39

Installation and Operation Manual for
Perenio® PEIRC01 Indoor Motor Camera
Doc Version: 2.6.1 ©Perenio IoT spol s r.o. All Rights Reserved
Page 8of 48
2.11 History and Push-Notifications ................................................................40
3 Maintenance and Repair ................................................................................41
4 Warranty Obligations ....................................................................................42
5 Storage, Transportation and Disposal of Devices..............................................45
6 Other Information.........................................................................................46
7 Troubleshooting............................................................................................47
8 Glossary ......................................................................................................48
Figures and Tables
Figure 1 –Front View.......................................................................................10
Figure 2 –Back View .......................................................................................10
Figure 3 –Viewing Angles ................................................................................14
Figure 4 –Pan/Tilt Angles.................................................................................15
Figure 5 –Scope of Supply...............................................................................15
Figure 6 - Examples of Installation ....................................................................20
Figure 7 –Mounting holes at the bottom of the Camera.......................................22
Figure 8 –Add new device procedure (The Camera activation process) .................27
Table 1 –Basic Technical Specifications .............................................................12
Table 2 –Types of connectors and USB Standards ..............................................18
Table 3 –Buttons and icons of the Camera Control Panel ....................................28
Table 4 –Buttons and icons of the “Recordings” tab............................................31
Table 5 –Available subscriptions.......................................................................35
Table 6 –Typical Errors and Troubleshooting Methods.........................................47
Connection to the Perenio Smart Mobile App
A. INSTALLATION OF THE PERENIO SMART MOBILE APP......................................22
B. DEVICE ACTIVATION BY QR CODE SCANNING ................................................24
C. SENDING WI-FI NETWORK DATA TO THE DEVICE...........................................25
D. LOCATION AND ROOM SETTING ...................................................................26

Installation and Operation Manual for
Perenio® PEIRC01 Indoor Motor Camera
©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.6.1
Page 9of 48
1 General Description and Specifications
1.1 General Purpose
The Perenio® PEIRC01 Indoor Motor Camera is specially designed for indoor
monitoring purposes. It can be used both as an independent device and as a part of
the Perenio Smart Building Management System, when various scenarios for
device interaction are activated. A special port allows you to connect external signaling
devices, while the HiSilicon Processor ensures high purity of colored images
throughout the day.
Key features of the Indoor Motor Camera are as follows:
High resolution video: Full HD 1080p, 2Mp;
Wider viewing angle: 90º;
Remote pan/tilt function: 350º/120º;
iOS (12.1 and higher) and Android (5.0 and higher) smartphone compatibility;
Wi-Fi connection;
MicroSD Card slot (up to 64GB);
Real-time video recording;
Setting up of an automatic video recording;
Built-in IR-filter and a Night Vision mode;
Increased visibility at night time;
Motion detection function;
Arm/Disarm mode;
Alarms and Push-notifications.

Installation and Operation Manual for
Perenio® PEIRC01 Indoor Motor Camera
Doc Version: 2.6.1 ©Perenio IoT spol s r.o. All Rights Reserved
Page 10 of 48
с
Figure 1 –Front View
Figure 2 –Back View
Microphone
IR LED
Panel
PIR Sensor
Camera
Lens
Light
Sensor
RJ-45
Port
Speaker
I/O Alarm
Ports
Power Port
Audio Out
Reset Button
MicroSD
Card Slot
Wi-Fi
Antenna

Installation and Operation Manual for
Perenio® PEIRC01 Indoor Motor Camera
©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.6.1
Page 11 of 48
Buttons, Ports and Indicators
Camera Lens
It forms an image of the monitored area
Microphone
It allows the User to hear sounds in the monitored area
PIR Sensor
A passive infrared sensor with a pyroelectric element
sensitive to changes in heat emission, which provides high
accuracy of motion detection
Light Sensor
It determines the level of illumination of the room and
disables the IR filter during the period of darkness to
maintain the video stream quality
IR LED Panel
The panel containing of eleven (11) infrared LEDs activated
in the case of insufficient level of illumination which allows
the User to get a high-quality image even in the dark
Wi-Fi Antenna
It is used to receive and transmit wireless Internet signals
RJ-45 Port
The cable port used for connection of the Camera to the
Ethernet router (This function is currently unavailable)
Audio Out
An additional port for the Mini-Jack connector aimed at
audio reproduction through an external audio device
Reset Button
It is used to reset the device to factory settings
MicroSD Card Slot
The slot for an SD Card generally intended to store video
recorded by the Camera
Power Port
The port for connecting the Camera to the mains
Speaker
It allows the User to send voice messages and thus
communicate with people and pets in the area of
monitoring
I/O Alarm Ports
It is used to connect external sensors to the Camera (This
function is currently unavailable)
ATTENTION! All Products and the Mobile Application of the Company (including
any future software and hardware whether in-house or third-party developed) are
not intended for emergency responses and cannot be used as fire-extinguishing
equipment and/or for emergency intervention, including but not limited to fires,
flooding, gas leaks or explosions, burglary and theft, as well as natural disasters
and other force majeure circumstances leading to damage and/or losses incurred
by the Client or caused to their estates, personal property and/or other products,
devices, personal data and privacy.

Installation and Operation Manual for
Perenio® PEIRC01 Indoor Motor Camera
Doc Version: 2.6.1 ©Perenio IoT spol s r.o. All Rights Reserved
Page 12 of 48
1.2 Technical Specification
Table 1 –Basic Technical Specifications
Parameter
Value
Article
PEIRC01
Processor
HiSilicon Hi3518E V200
Operating System
Embedded Linux
Onboard Memory Chips
Flash (PN): 25Q128FVSG
DDR (PN): Built-in
EPROM(PN): AT88SC0104CA
Compatibility
iOS (12.1 and higher) and Android (5.0 and higher)
Communication
Technology
Wi-Fi (EEE 802.11b/g/n)
Operating Frequency
2.4GHz
Bit Rate
802.11b (11 Mbps max), 802.11g (54 Mbps max),
802.11n (300 Mbps max)
WEP/WPA2 Encryption
Support of 64-/128-bit encryption
Image Sensor
Part Number: GC2033 (GalaxyCore)
Type: 1/2.7" CMOS, color
Lens: Board
Image Size: 1920х1080
Scanning: Progressive
Focal Length: 3.6 mm
Min Illumination: 0.5 lux
Aperture: Fixed
Resolution: 2MP
Lens Type
Glass
Horizontal/Vertical Viewing
Angle
90°/47° (See Figure 3 below)
Pan/Tilt (Remote)
350°/120°(See Figure 4 below)
Mechanical Pan/Tilt
N/A
Server
P2P
Audio Compression
Algorithm
G.726/G.711 (G.711 by default)

Installation and Operation Manual for
Perenio® PEIRC01 Indoor Motor Camera
©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.6.1
Page 13 of 48
Parameter
Value
Video Compression
Standard
H.264
Video Resolution
Main Stream: 1920х1080 (Full HD)
Sub-Stream: 640x480 (VGA)
Frame Rate
up to 30 fps (For 74.25Hz)
WDR Technology
Available
Video Recording Format
AVI
Audio Recording Format
WAV
Wi-Fi Chip
MT7601UN
Wi-Fi Antenna
Type: Standalone
Operating Frequency: 2.4GHz (14-channel)
Transmitting Power: 14dBm to 17dBm
Receiver Sensitivity: -92dBm до -68dBm
Antenna Gain: 2dBi
Zigbee Antenna
N/A
Support of SD Cards
Slot for MicroSD (up to 64GB)
Recommended Speed Class: Class 10
(Recording speed of not less than 10MByte/s)
Recommended Capacity: 32GB to 64GB
Format: FAT32
Mic
Built-in
Speaker
Built-in (Currently, not used)
IR Filter
Built-in
RJ-45 Port
Available (Currently, not used)
Additional Outputs
AUX OUT
External Sensor
Connection
4 I/O Alarm ports (Currently, external sensors are not
connected to this device)
PIR Sensor
Detection Angle: 90°
Detection Distance: 7 meters
Night Mode
11 IR LEDs, vision of up to 15 meters
Peak Wave Length: 850 nm

Installation and Operation Manual for
Perenio® PEIRC01 Indoor Motor Camera
Doc Version: 2.6.1 ©Perenio IoT spol s r.o. All Rights Reserved
Page 14 of 48
Parameter
Value
Power
Voltage: 5VDC
Current: 2.0A
Power Consumption: 5W (max)
Operating Temperature
0°C to +55°C (32°F～131°F)
Operating Humidity
20% to 85% (non-condensing)
Storage Temperature
-10°C to +60°C (14°F ～140°F)
Storage Humidity
0% to 90% (non-condensing)
Installation
On horizontal or vertical surface (Mounting holes
available). For indoor installation only.
Casing Material
ABS/PMMA
Color
White
Dimensions (L x W x H)
90 mm x 112 mm x 112 mm
Weight
278 g
Warranty Period
24 months
Service Life
24 months
Certification
CE, EAC, RoHS, UA.TR
Data Protection
GDPR Compliance
Figure 3 –Viewing Angles

Installation and Operation Manual for
Perenio® PEIRC01 Indoor Motor Camera
©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.6.1
Page 15 of 48
Figure 4 –Pan/Tilt Angles
1.3 Scope of Delivery
The following items and accessories are supplied within the PEIRC01 Indoor Motor
Camera package:
1. PEIRC01 Indoor Motor Camera (1 pc.)
2. Ethernet Cable (Length: 1.5 m) (1 pc.)
3. Power Adapter (Output: 5V, 2500mA, length: 1.5m) (1 pc.)
4. Quick Start Guide (1 pc.)
5. Warranty Card (1 pc.)
6. Stickers (2 pcs.)
1
2
3
Figure 5 –Scope of Supply*
* Images of accessories are provided for informational purposes only

Installation and Operation Manual for
Perenio® PEIRC01 Indoor Motor Camera
Doc Version: 2.6.1 ©Perenio IoT spol s r.o. All Rights Reserved
Page 16 of 48
1.4 Packaging and Labelling
The Perenio® PEIRC01 Motor Camera is supplied in a carton Gift Box of
201mm x 136mm x 97mm (L x W x H) containing the full name and marking of the
device, the list of accessories provided and basic technical specifications thereof, as
well as the date of manufacture and information about the Manufacturer of devices.
Carton package weight:
Net Weight: 278g;
Gross Weight: 661g.
1.5 Safe Operation Rules
For the proper and safe operation of Perenio® PEIRC01 Indoor Motor Cameras,
follow the instructions and safety procedures described in the present Manual. The
Manufacturer shall not be liable for any damage caused as a result of improper
operation of devices.
Safe Operation Conditions
1. The device shall be installed indoors only.
2. The User shall not try to pan/tilt the Camera head manually.
3. The User shall observe storage/transportation conditions, as well as the
operating temperature mode of the device as declared by the Manufacturer.
4. The User shall not install the device in the area with high humidity and high
content of dust and/or grease, as well as in the immediate vicinity of air
conditioners and ceiling fans.
5. The User must not disassemble or attempt to repair the device on their own.
6. The User must not drop, throw or bend the device.
7. In order to avoid personal injury, it shall not be allowed to use the cracked or
in any other way damaged device.
8. Use dry cloth or cloth soaked in a small amount of water for cleaning (don’t
use harsh chemicals/cleaning agents). The device must be powered off before
cleaning.
9. Children shall not be allowed to use the device unsupervised and/or play with it.

Installation and Operation Manual for
Perenio® PEIRC01 Indoor Motor Camera
©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.6.1
Page 17 of 48
1.6 The Use of Power Adapters
Only the original power adapter included in the delivery package, or some other
adapter recommended by Perenio IoT shall be used to power or charge the device.
This is due to the fact that an incompatible power adapter can cause longer charging
time, or a device failure, or a fire, whereas the original power adapter considers all
the mandatory technical parameters, namely:
a. Voltage the power supply output (See “OUTPUT, V” parameters on the adapter
body);
ATTENTION! The output voltage of the power adapter must strictly correspond
to the voltage consumed by the main device.
b. Current at the power supply output (See “OUTPUT, A/mA”on the adaptor
body);
NOTE. The current delivered by the power adapter must be equal to or slightly
higher than the rated current for the main device.
c. Polarity on the connector (pin) of the power adapter;
NOTE. The polarity indicates the part (external or internal) of the connector that
receives positive current.
The dot in the above image represents the connector’s inner contact, and the
crescent moon represents the outer contact. Most connectors have two contacts.
One contact carries a voltage (“+”), while the other –zero (“-”).
ATTENTION! The poles must not be interchanged.
Some devices are charged by or run on an AC power adapter. In this case, the
adapter has no indication of the polarity, and the AC “”symbol is shown next to
the indicated output voltage.
d. Configuration and size of the power adapter cable connector;

Installation and Operation Manual for
Perenio® PEIRC01 Indoor Motor Camera
Doc Version: 2.6.1 ©Perenio IoT spol s r.o. All Rights Reserved
Page 18 of 48
NOTE. Geometric shape, outer/inner diameter size and length of the power
adapter cable connector must match the parameters of the power port connector
of the main device.
Power adapters supplied by Perenio IoT with the devices have one of the following
types of cable connectors:
1. Standard cylindrical shaped connectors for powering the Indoor Motor Camera
and the Control Gateway.
2. USB connectors for powering the Indoor Fixed Camera, the IoT Router and the
Ion Diffuser (MicroUSB, Type-C).
There are also devices that are supplied only with a cable (without a power adapter), such
as Red Atom device and UV Mini Indigo lamp). Power cables for such devices are also
equipped with the second type of the connector.
Table 2 –Types of connectors and USB Standards
Standard
Parameters
Description
USB1.0
5V, up to 150mA
0.75W
DTS*: 12Mbps
Obsolete standard of information exchange and
connection methods (not used due to too low
data transfer rate)
USB2.0
5V, up to 500mA
2.5W
DTS*: 480Mbps
Suitable for devices with low power
consumption, but data can only be transmitted
in one direction at a time
USB3.0
5V, up to 900mA
4.5W
DTS*: 5Gbps
It supports backward compatibility with the old
standard. It has the same shape as USB2.0
Type-A, but colored blue. Data can be
transmitted in both directions at the same time
USB Type-C
(without
PD**)
Up to 5V, up to
3A
15W
DTS*: 10Gbps
This is an oval shaped connector with reversible
key. It can be used for data transfer of the
USB3.1 interface
USB-PD
Up to 20V, up to
5A
100W
DTS*: 10Gbps
This is a USB Type-C with a power transfer
function up to 100W. This option is suitable for
powerful devices (laptops, large tablets), but
may not be suitable for less powerful devices.

Installation and Operation Manual for
Perenio® PEIRC01 Indoor Motor Camera
©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.6.1
Page 19 of 48
Standard
Parameters
Description
Therefore, it is not used with Perenio®
devices
* DTS means data transfer speed
**PD means Power Delivery protocol
NOTE. USB Type-C is not USB3.1, because USB2.0, USB 3.0 or USB3.1 can be
used to supply power. On the other hand, USB Type-C is not USB Power Delivery
and does not necessarily support USB Power Delivery or USB3.1.
ATTENTION! Currently, Perenio IoT does not supply power adapters with
connectors that support USB-PD.
ATTENTION! Do not connect a USB-PD compatible power adapter (Power
Delivery fast charging standard) to the device. It is also not permitted to use the
charger to power or recharge incompatible devices (For more information on the
charger, see the technical specifications).
The manufacturer shall not be liable for any consequences, whether direct or indirect,
arising from the use of the power adapter for purposes other than its intended use, or
to supply power or charge the device not included in the scope of delivery.
As the power adapter cable connectors are subjected to daily stress, they can become
damaged over time. Below see basic signs of a faulty charger connector:
Unreasonable switching off of the device;
Unreasonable switching of the device to the battery mode;
Overheating of the USB plug;
Periodical switching off of the device in the absence of the mains failure;
Start of the charging process only after the cable is additionally fixed, or the
plug is reconnected;
No battery charging process when the power adapter is connected.
ATTENTION! Do not charge your device from external devices such as PC,
laptop, tablet or smartphone if the maximum current of 500mA/900mA (USB2.0
and USB3.0 ports, respectively) is insufficient to provide the required power input
level to the device.

Installation and Operation Manual for
Perenio® PEIRC01 Indoor Motor Camera
Doc Version: 2.6.1 ©Perenio IoT spol s r.o. All Rights Reserved
Page 20 of 48
2 Installation and Setup
Before installation, the User shall select one of the following possible locations and
mounting modes for the device:
On a horizontal surface (the floor, a table, a stand, etc.);
On a vertical surface (walls, furniture, etc.).
Also, make sure that the selected location meets the following requirements:
No clutter and obstructions in the Camera viewing angle area;
Flat and stable surface, as well as the mains socket near the installation site of
the Camera and/or mounting brackets.
Figure 6 - Examples of Installation*
* Images of accessories are provided for informational purposes only
NOTE. It is not recommended to install the device in areas with a high level of
noise and a high-frequency interference. Reinforced concrete floors may reduce
distance of wireless signal transmission. The Camera installation site shall protect
it from contact with moisture and foreign objects.