Perfect-10 Quinton VK-1516 User manual

www.classicexhibits.com
866.652.2100
© 2014
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - P10 -
Page 1 of 4
Step 1
patent D599,121
VK-1516 Quinton - General Layout
Plan View Perspective View
10’
10’

www.classicexhibits.com
866.652.2100
© 2014
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - P10 -
Page 1 of 4
Step 1
patent D599,121
Quinton - Backwall Assembly
Item
1
2
3
3a
4
5
6
7
8
Qty.
1
1
1
1
2
1
1
1
1
Steps:
NOTE: Assembly may be easiest if assembled face down on floor then lifted upright.
1) Connect upper curved vertical extrusions [3a,3,6] to leg assemblies [1,2,5].
2) Connect lower and upper horizontal extrusions between vertical assemblies by slightly
tightening BLACK knobs on backside of extrusion as shown.
NOTE: Make sure velcro faces toward back and knobs face horizontally as shown in detail.
** Various Accessories Available **
Description
Left Leg Assembly
Middle Leg Assembly
Upper Curved Vertical
Upper Curved Vertical
23”w Horizontal
Right Leg Assembly
Upper Curved Vertical
69”w Horizontal
69”w Horizontal
1
2
5
3a
3
6
4
4
7
8
Start Assembly of Backwall face
down on floor. Then lift upright.
Black
Knob
Horizontal
extrusion
Turn Knob Clockwise
to Tighten Lock
STAR indicates location of
knobs on BACKSIDE of unit.
Stopper Stopper
Stopper
Hinge Extrusion
Vertical
Connection Bar
Vertical Connection Bar -
Slide Bar into lower leg
assembly, secure in place.
Slide upper vertical over
bar and secure into place.
Step stool may be required
for assembly.
NOTE: When assembling horizontals they should be
placed approximately one inch from TOP and BOTTOM.
Slide
horizontal into groove
Assure
that a good
connection is made
and tighten to secure.

www.classicexhibits.com
866.652.2100
© 2014
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - P10 -
Page 2 of 4
Step 2
patent D599,121
Quinton - Backwall Attachments
Accessary Attachment
Attach header support to backwall then
attach header to support with velcro.
Header
Pins
Thumbscrew
Shelf
Shelf attaches to back of
sections 1 and 2 by setting
atop pins located on back
left side.
Light Connection
Attach lights to
backwall where
desired and
tighten in place.
Header
*
*
Attach back
plate and tighten
setscrew.
Attach top
plate and
tighten screws.
Attach back plate to connectors
on vertical extrusion using screws.
Then attach top plate and tighten
setscrews to secure.
Monitor Mount Attachment Cubby Attachment
Slide onto back pin first.
When attaching counter you will need to first
slide shelf onto back pin then set down on
front pin.
Shelf attaches to section
5 by setting atop pins
located on right side
and securing into place
with thumbscrew on left.

www.classicexhibits.com
866.652.2100
© 2014
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - P10 -
Page 3 of 4
Step 3
patent D599,121
Workstation Assembly
Part Number
A
B
C
D
Steps:
1) Connect lower horizontal extrusion [C] between bottom of leg assemblies [A and B] as shown.
2) Insert Laminated infill into grooves of leg assemblies [A and B].
3) Attach extrusion door between leg assemblies [A and B] and on top of laminated infill.
4) Attach upper horizontal extrusion w/ door stopper [D] between leg assemblies [A and B],
and set flush with top of legs [A and B].
Description
Left Leg Assembly
Right Leg Assembly
Horizontal Extrusion
Horiontal Extrusion w/ Door Stopper
Black
Knob
Turn Knob Clockwise
to Tighten Lock
DOOR
Laminated Infill
A (left)
B (right)
C
D (w/ Door Stopper)
Knobs face INSIDE
of workstation
Knobs face INSIDE
of workstation
Knobs face FORWARD
Pins are
located on INSIDE
FRONT vertical
of Leg
Assemblies
NOTE: Make sure the lock is flush with extrusion before tightening. If lock will not fully
engage, gently rock lock and extrusion back and forth while turning knob until lock
fully opens.
Align with bottom of leg assemblies [A and B].

www.classicexhibits.com
866.652.2100
© 2014
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - P10 -
Page 4 of 4
Step 4
patent D599,121
Workstation Assembly (Cont’d)
Part Number
E
F
Steps:
1) Attach horizontal extrusion [E] between vertical leg assemblies [A and B] as shown below.
2) Insert Laminated infill into grooves of vertical leg assemblies [A and B].
3) Attach upper horizontal extrusion [F] between vertical leg assemblies [A and B] atop infill.
4) Place internal shelf into assembled pedestal atop pins. .
5) Set Counter atop assembled pedestal and secure with velcro straps attached to underside of top.
6) Attach shelves to assembled pedestal where indicated using A10 clamps.
Description
Horizontal Extrusion
Horizontal Extrusion
E
Laminated
Infill
Knobs facing FORWARD
F
Knobs face INSIDE
of workstation
Place internal shelf into
workstation then
place counter atop
assembled workstation.
Internal
Shelf
Attach A10
atop stopper
When desired location
is found, tighten
set screw to secure.
Slide connector on back
of A10 clamp into groove
of extrusion.
Example of A10 Clamp Attachment
Tighten knob to
secure shelf in
place.
NOTE: Make sure the lock is flush with extrusion
before tightening. If lock will not fully engage,
gently rock lock and extrusion back and forth while
turning knob until lock fully opens.

www.classicexhibits.com
866.652.2100
© 2014
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - P10 -
patent D599,121
Case Packing - Case 1 of 3
Horizontal Extrusions 7 & 8
Vertical Connection Bar
Leg Assembly
5
Leg Assembly
1
Vertical Connection Bar
Horizontal Extrusion 4
Horizontal Extrusion 4
Header Supports
Level 1 Level 2 Level 3 Level 4 Level 5
Top View of Each Level
Leg Assembly
2
Vertical Connection Bar
Header
Additional Items:
- Setup Instructions

www.classicexhibits.com
866.652.2100
© 2014
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - P10 -
patent D599,121
Case Packing - Case 2 of 3
Level 1
Top View of Each Level
Backside
Shelf
Cubby
Graphics
Setup Hardware
Halogen Lights

www.classicexhibits.com
866.652.2100
© 2014
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - P10 -
patent D599,121
Case Packing - Case 3 of 3
Level 1 Level 3
Top View of Each Level
Level 2
Door
Level 4
Leg Assembly
B
Horiz. Extrusion F
Horiz. Extrusion D
Level 5
Leg Assembly
A
Horiz. Extrusion E
Horiz. Extrusion C
Front Panel
Shelf
Top
Shelf