Performance Tool W41022 User manual

OWNER'S MANUAL
WARNING: READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS AND
WARNINGS BEFORE OPERATING THIS TOOL. FAILURE TO DO SO MAY
RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE AND WILL
VOID WARRANTY.
3 TON
JACK STANDS
Item Number W41022

2
CAUTION Indicates a potentially
hazardous situation that, if not avoided,
MAY result in minor or moderate injury.
NOTICE Indicates important information,
which if not followed, MAY cause damage
to equipment.
DANGER Indicates an imminently
hazardous situation that, if not avoided,
WILL result in death or serious injury.
WARNING Indicates a potentially
hazardous situation that, if not avoided,
COULD result in death or serious injury.
Specifications are subject to change without notice.
WARNING
READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS AND WARNINGS BEFORE
OPERATING THIS TOOL. FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY
AND/OR PROPERTY DAMAGE AND WILL VOID WARRANTY.
WARNING: Failure to heed these warnings may result in loss of load, damage to jack
stands, and/or jack stand failure resulting in personal injury or property damage.
WARNING: Do not overload jack stands beyond rated capacity. Overloading can cause
damage to or failure of the jack stands.
WARNING: POSITION LOAD ON CENTER OF SADDLE ONLY. ALWAYS USE
STANDS IN PAIRS ON HARD, LEVEL SURFACE CAPABLE OF SUSTAINING THE
LOAD. USE OF STANDS ON OTHER THAN HARD LEVEL SURFACES CAN RESULT IN
STAND INSTABILITY AND POSSIBLE LOSS OF LOAD.
Be sure all personnel are clear of load before lowering load.
Ensure that no personnel pass underneath load until load is securely supported by
jack stands.
WARNING: Read and understand this entire instruction manual before attempting to
assemble, install, operate or maintain this product. Failure to comply with the instructions
may result in serious personal injury and/or property damage!
The following signal words are used to emphasize safety warnings that must be followed
when using this product:
This instruction manual is intended for your benefit. Please read and follow the safety, installation, maintenance and
troubleshooting steps described within to ensure your safety and satisfaction. The contents of this instruction
manual are based upon the latest product information available at the time of publication. The manufacturer
reserves the right to make product changes at any time without notice.
Capacity................................................................................................................. 6,000 lbs.
Minimum Lift Height...................................................................................................... 12 in.
Maximum Lift Height............................................................................................... 17-1/4 in.
Range....................................................................................................................... 5-1/4 in.
SAFETY GUIDELINES / DEFINITIONS
SPECIFICATIONS
SAFETY INFORMATION

3
1. Refer to your vehicle owner's manual for proper jacking procedures. Lift only on areas
of the vehicle as specified by vehicle manufacturer.
2. Position stands under vehicle at points specified by vehicle manufacturer as proper load
support points.
3. To adjust stands: Hold control lever
up while lifting saddle shaft to
desired height. Push control lever
down to lock pawl into teeth located
in center column. MAKE SURE
PAWL IS FULLY ENGAGED
INTO TEETH.
4. Carefully lower load onto stands.
Saddle
Pawl
Center
Column
Control
Lever
1. Visual inspection shall be made before each use of the stands, checking for cracks,
cracked welds and missing and/or damaged parts. Any stand that appears to be
damaged in any way shall be removed from service immediately.
2. BECAUSE OF THE POTENTIAL HAZARDS ASSOCIATED WITH THE MISUSE OF
EQUIPMENT OF THIS TYPE, NO MODIFICATIONS SHALL BE MADE TO THE PRODUCT.
MAINTENANCE
UNPACKING/INSPECTION
After opening the carton, unpack your new product and related parts & accessories.
Please inspect it carefully for any damage that may have occurred during transit. Please
check it against the photograph on carton. If any parts are missing, please call customer
service at 1-800-426-1262 between 6 a.m. and 5 p.m. Pacific time.
WARNING: DO NOT operate this product if damaged during shipment, handling or
misuse. Do not operate the product until the parts have been replaced or the fault rectified.
Failure to do so may result in serious personal injury or property damage. All damaged
parts must be repaired or replaced as needed prior to operating this product. Check to see
that all nuts, bolts and fittings are secure before putting this product into service. If you
have any questions, or require assistance with damaged or missing parts, please contact
our factory customer service department at: 1-800-426-1262.
Please have the serial number, model number, and date of purchase available for
reference when calling.
OPERATION

LIMITED WARRANTY
PERFORMANCE TOOL® extends only the following warranties, and only to original retail purchasers. These
warranties give specific legal rights. Except where prohibited by local law, the law of the State of Washington
governs all warranties and all exclusions and limitations of warranties and remedies. There may be other rights
which vary from state to state.
PERFORMANCE TOOL® warrants the product to be free from defects in materials and workmanship under normal
use and service. A defective product may be returned for a free replacement within 90 days from the date of
purchase, provided that product is returned to place of purchase immediately after discovery of defect. After 90
days and up to one year from date of purchase, PERFORMANCE TOOL® will replace at no charge any parts which
our examination shall disclose to be defective and under warranty. These warranties shall be valid only when a sales
receipt showing the date of purchase accompanies the defective product or defective part (s) being returned. For
part (s) after 90 days, please remit your request, postage prepaid to:
PERFORMANCE TOOL, P.O. Box 88259 Tukwila, WA 98138
These warranties exclude blades, bits, punches, dies, bulbs, fuses, hoses, and other consumables which must be
replaced under normal use and service. These warranties shall not apply to any product or part which is used for a
purpose for which it is not designed, or which has been repaired or altered in any way so as to affect adversely its
performance or reliability, nor shall these warranties apply to any product or part which has been subject to misuse,
neglect, accident or wear and tear incident to normal use and service.
PERFORMANCE TOOL® does not authorize any other person to make any warranty or to assume any liability in
connection with its products.
Except for warranties of title and the limited express warranties set forth above, PERFORMANCE TOOL® makes no
express or implied warranties of any kind with respect to its products. In particular, PERFORMANCE TOOL® makes
no implied warranty of merchantability and no implied warranty of fitness for any particular purpose, except that for
goods purchased primarily for personal, family or household use and not for commercial or business use,
PERFORMANCE TOOL® makes an implied warranty of merchantability (and, if otherwise applicable, an implied
warranty of fitness for a particular purpose), but only for the particular qualities or characteristics, and for the
duration, expressly warranted above.
The laws on limitation of implied warranties may differ from state to state, so the above limitations may not apply in
all cases.
PERFORMANCE TOOL® shall not be liable for consequential, incidental or special damages resulting from or in any
manner related to any product, or to the design, use, or any inability to use the product. The sole and exclusive
remedy for a defective product or part shall be the repair, or replacement thereof as provided above. The laws on
limitation of remedies or on consequential, incidental or special damages may vary from state to state, so the above
limitations may not apply in all cases.
© Copyright 2019 WILMAR CORPORATION, P.O. Box 88259 Tukwila, WA 98138