Performance Tool W54010 User manual

ROLLER SUPPORT STAND
OWNER'S MANUAL
Item Number W54010
FOR YOUR SAFETY,
please read these instructions carefully and retain them for future use.
WARNING!
READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS AND
WARNINGS BEFORE OPERATING THIS TOOL. FAILURE TO DO SO
MAY RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE
AND WILL VOID WARRANTY.

2
SPECIFICATIONS
Specifications are
subject to change
without notice
IMPORTANT SAFETY INFORMATION
WARNING!
READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS AND
WARNINGS BEFORE OPERATING THIS TOOL. FAILURE TO DO
SO MAY RESULT IN PERSONAL INJURY AND/OR PROPERTY
DAMAGE AND WILL VOID WARRANTY.
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Ensure roller support stand is set up on firm, level
ground in a stable manner.
3. Keep children away. Children must never be allowed in the work area. Do not let them
handle machines, tools or extension cords.
4. Be aware of over-balancing. When a large piece is cut from one end of a job the
remaining piece may be heavy enough to tip the stander. Always ensure the workpiece
is well supported.
5. Use the right tool for the job. Do not modify this tool and do not use this tool for a
purpose for which it was not intended.
6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving
parts. Protective, electrically non-conductive clothes and non-skid footwear are recom-
mended when working. Wear restrictive hair covering to contain long hair.
7. Use eye and ear protection. Always wear ANSI approved impact safety goggles.
8. Work Safe. Keep proper footing and balance at all times. Never use support stand as step
ladder nor stand on support stand top. Never exceed recommended maximum weight
capacity of support stand (132 lbs.). Always lower heavy loads onto stand gently, so that
strain is taken up gradually.
9. Stay alert. Watch what you are doing and use common sense. Do not operate any tool
when you are tired.
10. Check to make sure that all fixing screws and knobs are tight and all legs are locked
into place before operating the stand.
11. Check damaged parts. Before further use of tool it should be carefully checked to
determine that it will operate properly and perform its intended function.
12. Do not operate any tool if under the influence of alcohol or drugs. Read warning labels
on prescriptions to determine if your judgment or reflexes are impaired while taking
drugs. If there is any doubt, do not operate any tool.
13. When not in use, tools should be stored in a dry locked-up place, out of the reach of
children and do not allow persons unfamiliar with it.
Height: ................................................27 - 43 in.
Width: ........................................................ 17 in.
Roller Width: ............................................. 11 in.
Weight Capacity: .................................. 132 Ibs.
Weight: ................................................... 8.8 Ibs.

IMPORTANT SAFETY INFORMATION
WARNING: The use of any accessory or attachment other than one recommended in this
instruction manual may present a risk of personal injury.
WARNING:
The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be understood by the
operator that common sense and caution are factors which cannot be built into this product, but
must be supplied by the operator. Read and understand all of the instructions provided in the
instruction manual as well as any other tool (s) used with the roller support stand.
Use hex key provided.
1. Remove the pins from the leg assembly (3) and insert
the pins into the holes of the stand assembly (4) as
shown in Fig. 1. Connect the leg assembly and stand
assembly with the hex bolt as shown in Fig 2. Use
the hex key to tighten the hex bolt, make sure the leg
assembly is locked firmly as shown in Fig 3. Repeat
this step with the other leg assembly.
ASSEMBLY INSTRUCTIONS
PARTS DESCRIPTION
1. Roller Assembly
2. Height Adjustment Handle
3. Leg Assembly
4. Stand Assembly
5. Hex kex & Hardware
Fig. 1
1
2
3
4
5
Fig. 2
Fig. 3
3

LIMITED WARRANTY
PERFORMANCE TOOL® extends only the following warranties, and only to original retail purchasers. These
warranties give specific legal rights. Except where prohibited by local law, the law of the State of Washington
governs all warranties and all exclusions and limitations of warranties and remedies. There may be other rights
which vary from state to state.
PERFORMANCE TOOL® warrants the product to be free from defects in materials and workmanship under normal
use and service. A defective product may be returned for a free replacement within 90 days from the date of
purchase, provided that product is returned to place of purchase immediately after discovery of defect. After 90
days and up to one year from date of purchase, PERFORMANCE TOOL® will replace at no charge any parts which
our examination shall disclose to be defective and under warranty. These warranties shall be valid only when a
sales receipt showing the date of purchase accompanies the defective product or defective part (s) being returned.
For part (s) after 90 days, please remit your request, postage prepaid to:
PERFORMANCE TOOL, P.O. Box 88259 Tukwila, WA 98138
These warranties exclude blades, bits, punches, dies, bulbs, fuses, hoses, and other consumables which must be
replaced under normal use and service. These warranties shall not apply to any product or part which is used for a
purpose for which it is not designed, or which has been repaired or altered in any way so as to affect adversely its
performance or reliability, nor shall these warranties apply to any product or part which has been subject to
misuse, neglect, accident or wear and tear incident to normal use and service.
PERFORMANCE TOOL® does not authorize any other person to make any warranty or to assume any liability in
connection with its products.
Except for warranties of title and the limited express warranties set forth above, PERFORMANCE TOOL® makes no
express or implied warranties of any kind with respect to its products. In particular, PERFORMANCE TOOL® makes
no implied warranty of merchantability and no implied warranty of fitness for any particular purpose, except that for
goods purchased primarily for personal, family or household use and not for commercial or business use,
PERFORMANCE TOOL® makes an implied warranty of merchantability (and, if otherwise applicable, an implied
warranty of fitness for a particular purpose), but only for the particular qualities or characteristics, and for the
duration, expressly warranted above.
The laws on limitation of implied warranties may differ from state to state, so the above limitations may not apply in
all cases.
PERFORMANCE TOOL® shall not be liable for consequential, incidental or special damages resulting from or in any
manner related to any product, or to the design, use, or any inability to use the product. The sole and exclusive
remedy for a defective product or part shall be the repair, or replacement thereof as provided above. The laws on
limitation of remedies or on consequential, incidental or special damages may vary from state to state, so the above
limitations may not apply in all cases.
© Copyright 2021 WILMAR CORPORATION, P.O. Box 88259 Tukwila, WA 98138
2. Put the roller assembly (1) on the stand
assembly and connect them with two hex bolts
and washers (5). Use the hex key to tighten the
hex bolts as show in Fig 4.
3. You can adjust the height of the stand with the
adjustment handle by turning counter-clockwise
to loosen. While loose, raise the roller assembly
to desired height and turn adjustment handle
clockwise to tighten in place as shown in Fig 5.
NOTE: Set the roller assembly parallel with a
support stand or other saw table to better support
longer work-pieces.
ASSEMBLY INSTRUCTIONS CONT.
Fig. 4
Fig. 5