Performance Tool W41021 User manual

WARNING
It is the owner and/or operators’ responsibility to study all WARNINGS, operating, and maintenance instructions contained on the
product label and instruction manual prior to operation of this product. The owner/operator shall retain product instructions for future
reference.
The owner and/or operator are responsible for maintenance, maintaining all decals or warning labels and while in use, maintaining
the unit in good working order. If the owner and/or operator are not fluent in English, the product warnings and instructions shall be
read and discussed with the operators’ native language by the purchaser/owner or his designee. Make sure that the operator
comprehends its contents. Safety information shall be emphasized and understood prior to usage. The product shall be inspected per
the operating instructions.
Users of this product must fully understand these instructions. Each person operating this product must also be of sound mind and
body and must not be under the influence of any substance that might impair their vision, dexterity, or judgment.
Protect yourself and others by observing all safety information.
Failure to comply with instructions could result in personal injury and/or property damage!
If you encounter any problems or difficulties, please contact our customer service department at:
1-800-426-1262 between 6:30 a.m. and 4:30 p.m. Pacific time.
2 TON
JACK STANDS
OWNER’S MANUAL
Item Number W41021

2
DANGER Indicates an imminently
hazardous situation that, if not avoided,
WILL result in death or serious injury.
WARNING Indicates a potentially
hazardous situation that, if not avoided,
COULD result in death or serious injury.
SAFETY GUIDELINES / DEFINITIONS
UNPACKING AND INSPECTION
SPECIFICATIONS
Specifications are subject to change without notice.
WARNING: Read and understand this entire instruction manual before attempting to
assemble, install, operate or maintain this product. Failure to comply with the instructions
may result in serious personal injury and/or property damage!
The following signal words are used to emphasize safety warnings that must be followed
when using this product:
This instruction manual is intended for your benefit. Please read and follow the safety, installation, maintenance and
troubleshooting steps described within to ensure your safety and satisfaction. The contents of this instruction
manual are based upon the latest product information available at the time of publication. The manufacturer
reserves the right to make product changes at any time without notice.
After opening the carton, unpack your new product and related parts & accessories.
Please inspect it carefully for any damage that may have occurred during transit. Please
check it against the photograph on carton. If any parts are missing, please call customer
service at 1-800-426-1262 between 6 a.m. and 5 p.m. Pacific time.
WARNING DO NOT operate this product if damaged during shipment, handling or
misuse. Do not operate the product until the parts have been replaced or the fault rectified.
Failure to do so may result in serious personal injury or property damage. All damaged
parts must be repaired or replaced as needed prior to operating this product. Check to see
that all nuts, bolts and fittings are secure before putting this product into service. If you
have any questions, or require assistance with damaged or missing parts, please contact
our factory customer service department at: 1-800-426-1262.
Please have the serial number, model number, and date of purchase available for
reference when calling.
Capacity: ............................................................................................................. 4,000 lbs.
Minimum Lift Height:........................................................................................... 10 3/4 in.
Maximum Lift Height:.......................................................................................... 16 3/4 in.
Base Length:....................................................................................................... 6 11/16 in.
Base Width:........................................................................................................ 6 15/16 in.
CAUTION Indicates a potentially
hazardous situation that, if not avoided,
MAY result in minor or moderate injury.
NOTICE Indicates important information,
which if not followed, MAY cause damage
to equipment.

3
IMPORTANT SAFETY INFORMATION
OPERATION
MAINTENANCE & INSPECTION
WARNING
READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS AND WARNINGS BEFORE OPERATING THIS
TOOL. FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE AND WILL
VOID WARRANTY.
Warning: Failure to heed these warnings may result in loss of load, damage to jack stands, and/or
jack stand failure resulting in personal injury or property damage.
Warning: Do not overload jack stands beyond rated capacity. Overloading can cause damage to or
failure of the jack stands.
Warning: POSITION LOAD ON CENTER OF SADDLE ONLY. ALWAYS USE STANDS IN PAIRS
ON HARD, LEVEL SURFACE CAPABLE OF SUSTAINING THE LOAD. USE OF STANDS ON
OTHER THAN HARD LEVEL SURFACES CAN RESULT IN STAND INSTABILITY AND
POSSIBLE LOSS OF LOAD.
Be sure all personnel are clear of load before lowering load.
Ensure that no personel pass underneath load until load is securely supported by jack stands.
1. Refer to your vehicle owner's manual for proper jacking procedures. Lift only on areas
of the vehicle as specified by vehicle manufacturer.-
2. Position stands under vehicle at points specified by vehicle manufacturer as proper
load support points.
3. To adjust stands: Hold control lever
up while lifting saddle shaft to
desired height. Push control lever
down to lock pawl into teeth
located in center column. MAKE
SURE PAWL IS FULLY
ENGAGED INTO TEETH.
4. Carefully lower load onto stands.
Saddle
Pawl
Center
Column
Control
Lever
1. Visual inspection shall be made before each use of the stands, checking for cracks,
cracked welds and missing and/or damaged parts. Any stand that appears to be
damaged in any way shall be removed from service immediately.
2. BECAUSE OF THE POTENTIAL HAZARDS ASSOCIATED WITH THE MISUSE OF
EQUIPMENT OF THIS TYPE, NO MODIFICATIONS SHALL BE MADE TO THE
PRODUCT.

1 YEAR LIMITED WARRANTY
PERFORMANCE TOOL® extends only the following warranties, and only to original retail purchasers. These warranties give specific legal
rights. Except where prohibited by local law, the law of the State of Washington governs all warranties and all exclusions and limitations of
warranties and remedies. There may be other rights which vary from state to state.
PERFORMANCE TOOL® warrants the product to be free from defects in materials and workmanship under normal use and service. A
defective product may be returned for a free replacement within 90 days from the date of purchase, provided that product is returned to
place of purchase immediately after discovery of defect. After 90 days and up to one year from date of purchase, PERFORMANCE TOOL®
will replace at no charge any parts which our examination shall disclose to be defective and under warranty. These warranties shall be valid
only when a sales receipt showing the date of purchase accompanies the defective product or defective part(s) being returned. For part(s)
after 90 days, please remit your request, postage prepaid to:
PERFORMANCE TOOL, P.O. Box 88259 Tukwila, WA 98138
These warranties exclude blades, bits, punches, dies, bulbs, fuses, hoses, and other consumables which must be replaced under normal
use and service. These warranties shall not apply to any product or part which is used for a purpose for which it is not designed, or which
has been repaired or altered in any way so as to affect adversely its performance or reliability, nor shall these warranties apply to any
product or part which has been subject to misuse, neglect, accident or wear and tear incident to normal use and service.
PERFORMANCE TOOL® does not authorize any other person to make any warranty or to assume any liability in connection with its
products.
Except for warranties of title and the limited express warranties set forth above, PERFORMANCE TOOL® makes no express or implied
warranties of any kind with respect to its products. In particular, PERFORMANCE TOOL® makes no implied warranty of merchantability
and no implied warranty of fitness for any particular purpose, except that for goods purchased primarily for personal, family or household
use and not for commercial or business use, PERFORMANCE TOOL® makes an implied warranty of merchantability (and, if otherwise
applicable, an implied warranty of fitness for a particular purpose), but only for the particular qualities or characteristics, and for the
duration, expressly warranted above. The laws on limitation of implied warranties may differ from state to state, so the above limitations
may not apply in all cases.
PERFORMANCE TOOL® shall not be liable for consequential, incidental or special damages resulting from or in any manner related to any
product, or to the design, use, or any inability to use the product. The sole and exclusive remedy for a defective product or part shall be the
repair, or replacement thereof as provided above. The laws on limitation of remedies or on consequential, incidental or special damages
may vary from state to state, so the above limitations may not apply in all cases.
© Copyright 2012 WILMAR CORPORATION, P.O. Box 88259 Tukwila, WA 98138