Perlesmith PSMFK9 User manual

PSMFK9
V3.0
MEDIUM FULL-MOTION TV WALL MOUNT
Thank you for choosing our product! We strive to provide the
best quality and services for our customers. Would you kindly
share your experience on Amazon if you are satisfied? Should
you have any issues, please don't hesitate to contact us.
Telephone：
800-5566-806 Mon-Fri 10am - 6pm (PST) (USA) (CAN)
Email：
[email protected](US/CA/DE/UK/FR/IT/ES/JP/AU)

1 PC
2 PCS
1
Level
1 PC
IMPORTANT SAFETY INFORMATION
Tools Needed (Not lncluded)
WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT
FROM IMPROPER INSTALLATION OR ASSEMBLY. READ FOLLOWING
WARNINGS BEFORE BEGINNING.
If you do not understand the instructions or have any concerns or questions, please contact
customer service at [email protected]
Do not install or assemble if the product or hardware is damaged or missing. Not all parts and
hardware included will be used. lf you require replacement parts, contact customer service at
[email protected]
This product may contain moving parts. Use with caution.
DO NOT INSTALL INTO DRYWALL ALONE.
Please check www.perlesmith.com for more products and company information.
Stud finder Tape measure Pencil Drill
7/32 in.(5.5mm)
Wood Drill
25/64 in.(10mm)
Concrete Drill
25/64in.(10mm)
Socket wrench
1/2in.(13mm)
Socket wrench Screw driver
Hammer
Supplied Parts
01
02
03

Step 1 Before TV Bracket Installation
2
2.95 in. 3.94 in.
11.81 in.
7.87 in.
15.75 in.
Measure the distance between the holes located at the back of
your TV (these measures may form the shape of a square,or a
rectangle) and check that these taken measures are within the
VESA(*)range for this wall mount.
(*)VESA:International standard established by the TV
manufacturers used to determine if LCD/LED TVs are
compatible with wall mounts.
Supplied Hardware
Hardware for Attaching TV Bracket to TV
Washers
M8
x4
A2
Spacers
L10mm
x8
Philips Screws
M6 x 15mm
M6 x 30mm
x4x4
D1 D2
Philips Screws
M8 x 15mm
M8 x 45mm
x4
x4
E1 E2
B2
Spacers
L5mm
x8
C
Washers
M6
x4
B1
Hardware for Attaching Wall Plate to Wall
M8X65
Lag Bolts
x4
A3
x4
A1
Wall
Anchor
CAUTION!
!
Philips Screws
M4 x 30mm
F
x4
These anchors are
for concrete or brick
walls ONLY. DO NOT
use them in drywall or
wood studs.

Step 1 Before TV Bracket Installation
For Flat screen TV
For Curved TV/Extra Space
Step 2 Install TV Bracket
3
D1 E1
B1
B2/C
D22/F
B1
Manual Only!
Manual Only!
Manual Only!
Hand thread screws into the threaded inserts
on the back of your TV to determine which
screw diameter (M4, M6, or M8) to use
When attaching brackets to the flat screen, be careful not to over tighten screws and be
sure that screws do not bottom out in the mounting holes.
Too Short Too Long Correct Correct
02
02
E2

STEP 3A Wood Stud Option
3A-1 3A-2 Ensure marking at
the center of the
stud.
4
Center line
Use a stud finder (not included) to locate wood
stud. Mark the edge and center locatons.
WARNING:
WARNING:
Ensure the wall plate is securely fastened to the wall before
continuing on to the next step.
● Drywall covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum
1½ x 3½ in. (38 x 89 mm)
● Stud center must be verified
WARNING:
Avoid potential personal injury or property damage! DO NOT
over-tighten the lag bolts [A1]. Tighten the lag bolts [A1] only until
the washers [A2] are pulled firmly against the wall plate [01]. X
01
STEP 3 Attach Wall Plate to Wall
For wood stud installation, follow STEP 3A
For concrete installation, follow STEP 3B
03

3A-3 3A-4
60
5.5
5
A1
A2
Drill 4pilot holes using a 7/32 in.
(5.5mm) Wood Drill diameter drill
bit.Make sure the depth is not less than
60mm.
Mount the wall plate using 4 sets of M8X65
in.lag bolts A1 and washers A2 with a 1/2
in.socket wrench(not included).
1/2in.(13mm)
socket wrench
STEP 3B Solid Concrete or Concrete Block Option
Avoid potential personal injury or property damage! DO NOT
over-tighten the lag bolts [A1]. Tighten the lag bolts [A1] only until the
washers [A2] are pulled firmly against the wall plate [01].
WARNING:
Wall
Anchor
A3
WARNING:
Ensure the wall plate is securely fastened to the wall
before continuing on to the next step.
WARNING:
Avoid potential personal injuries and property damage!
● Mount the arm assembly/wall plate [01] directly onto the concrete
surface
● Minimum solid concrete thickness: 203 mm (8 in.)
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
01
03

3B-1 3B-2
3B-3
A3
Position the wall plate at your desired
height, level the wall plate and mark the
pilot hole locations.
Install wall plate using lag bolts [A1], washers [A2] and anchors
[A3]. Be sure the anchors [A3] are seated flush with the
concrete surface. Tighten the lag bolts [A1] only until the
washers [A2] are pulled firmly against the wall plate[01] . DO
NOT over-tighten the lag bolts [A1].
Step 4 Mounting your TV to the Brackets
Use the hammer to knock
anchors [A3] into the wall.
6
A1
A2
A3
70mm
ø10mm
Drill 4 pilot holes using a 25/64 in.(10mm)
diameter drill bit.Make sure the depth is not
less than 23/4in.(70mm).
Iocking
01
01
03
03

Step 6 Tilt Adjustment
7
Tilt adjustment 25/64in.(10mm)
socket wrench
Step 5 Level Adjustment
If needed, the TV can be leveled