Perlesmith PSSS1 User manual

Loosen
Lift
Tighten
Phillips Screwdriver
UNPACKING INSTRUCTIONS AND IMPORTANT SAFETY INFORMATION
x 2
x 2
x 2 x 2 x 2
01
03
04 05 06
Base
Post Assembly
x 2
02
Post Extension
90 Degree Plate Square Plate Narrow Plate
STEP 1 Attach the nails or rubber pads to the base feet
STEP 2A Fasten the post assemblies to the bases(for regular lower height)
STEP 2B Fasten the post extensions and post assemblies to the bases(for
extra higher height)
1
2 3
03
02
STEP 3 Adjust post assemblies to the desired height
02
01
Tighten
01
B
OPT
A
A
0101
01
OPT
B
C
0101
03
01
Washer
M4/M5
Bolt
M6x12mm
Bolt
#6-32 x 1 1/4″
Nut
#6-32
Washer
#6
K L M N O
x4 x2 x2 x2
Washer
#6 x #14
P
x4
Bolt
1/4″x13.5mm
For marble or wooden floor, rotate and
insert the rubber pads into the holes of the
base.
The plastic packaging bag of the posts and bases come with yellow and blue labels. ONLY assemble the
posts and base labelled THE SAME COLOR. Otherwise it will be difficult to assemble.
Nail Nut Pad Sponge Plastic Nut Bolt
M5x8mm
Bolt
M5X12mm
Bolt
1/4″x12mm
Bolt
M4X12mm
•Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage.
•Check package contents against the Supplied Parts and Hardware List to assure that all components were
received undamaged. Do not use damaged or defective parts.
•Not all parts and hardware included will be used. lf you require replacement parts, please contact customer
service at [email protected] (US)/[email protected] (CA).
•Carefully read all instructions before attempting installation.
•If you do not understand the instructions or have any concerns or questions, please contact customer service at
[email protected] (US)/[email protected] (CA).
•This product may contain moving parts. Use with caution.
•Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight
capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
STEP 2B-1 Secure the post assemblies [03] to the
post extensions [02]
STEP 2B-1 Fasten the post extensions [02] and
post assemblies [03] to bases [01]
Speaker Floor Stand
Instruction Manual V6.0
Thank you for choosing this PERLESMITH product! At
PERLESMITH we strive to provide you with the best quality
products and services in the industry. Please share your
experience of our product with others at www.perlesmith.com/
pages/reviews if you are satisfied. Should you have any issues,
please don't hesitate to contact us.
Technical Support:
1-800-556-6806 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected] (US)
[email protected] (CA)
Website:
www.perlesmith.com
Model:PSSS1/PSSS1W
For carpets floor,screw the nails into the
holes of the base.

[F]
[E]
[03]
[05]
04
06
[05]
04
04
G
[03]
04
G
H
E
E
F
I
J
K
STEP 4 Secure speaker to stand
4 5
6 7
L
Speaker option B2: keyhole insert
OPT
C
OPT
B2
K
P
All of us at PERLESMITH do appreciate your product purchase. We hope that you
are as happy with your product as we are designing and manufacturing it for you.
We strive to provide you with the best quality products and services in the
industry. Please share your experience of our product with others at
www.perlesmith.com if you are satisfied. If you have any questions please don't
hesitate to contact us at
Technical Support: 1-800-556-6806 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info: [email protected] (US)/[email protected] (CA)
Please check www.perlesmith.com for more products and company information.
Thank you again for
choosing this PERLESMITH product!
04
N
K
②
G
04
(Suitable for Samsung SWA-8500S,
SWA-9000S Speakers)
1.Slide the washer [O] into the bolt [M], then insert
them into the keyhole.
2.Tighten the nut [N] until the washer [K] is pulled
firmly against the 90 degree plate [04].
1.Slide the washer [O] into the bolt [M], then insert
them into the keyhole.
2.Tighten the nut [N] until the washer [K] is pulled
firmly against the 90 degree plate [04].
O
M
①
Speaker option A: two thread
inserts
Speaker option B1: keyhole insert
Note: The washers
[K] are only suitable
for bolts [J] and [H]
OPT
A
OPT
B1
1. Insert bolt [F] through 90 degree plate [04]
2. Thread plastic nut [E] to bolt [F]
3. Insert bolt [F] into keyhole and fasten the
plastic nut [E]
4. Use the washer [P] to adjust the length of the
bolt [F] if necessary.
STEP 5 Route the cables
(If Needed)