Perrin & Rowe PHOENICIAN E.4360 Operation manual

370
225
230
60ø
130
50 ø
30 ø Hole
35Ø Hole
Hose Length
1200mm
45 Max
10mm
N.R.V

370
225
230
60ø
35Ø Hole

45 Max
10mm

Figure 1. Installation of Centrebody
Phoenician Monobloc Sink Mixer with Rinse E.4360
Phoenician Monobloc Sink Mixer with Lever Handles E.4460
Congratulations on the purchase of your Perrin & Rowe kitchen tap!
The Traditional Kitchen Collection
Installation & User Guide
PHOENICIAN - E.4360, E.4460
1
3/8"
Hole
Diameter
Base Seal
Nut
Box Spanner
Clamp Plate
Securing Stud
35mm
Hole
Diameter
Base Seal
Nut
Box Spanner
Clamp Plate
Securing Stud
Correctly installed and with sensible care, it will give many years of trouble
free service.
Before you proceed... We recommend you engage the services of a registered
plumber to install this product.
Read the instructions and diagrams in this leaflet carefully.
Preparation
1) Flush the plumbing system before installing the tap.This is to avoid
plumbing residues clogging or possibly damaging the ceramic valves. It
is especially important where extensive plumbing work has been carried
out.
For ease of possible future servicing, we recommend the fitting of conve-
niently placed isolating valves.
Check List
l Temperature of the hot water supply does not exceed 85 C.
l
Recommended minimum water supply pressure - 1 bar .
l
Ideal performance obtained with equal hot and cold pressure.
l Recommended maximum water supply pressure - 5 bar.
Phoenician Monobloc Assembly- Refer to Figure 1.
2) Hot supply should be on the left when viewed from the front of the fitting.
3) Monobloc mixers require a 35mm diameter hole through the surface they
are to be installed on. Maximum counter-top thickness 45mm.
4) Insert the flexible connections through the hole ensuring that the base
ring and seal are in place between the mixer and mounting surface.
Connect these to the relevant supply lines.
5) From the underside of the counter-top, place the clamp plate on securing
stud and using the box spanner supplied, put fixing nut in spanner and
tighten until mixer is held firmly in position. See Figure 1.
Rinse
6) The rinse units require a 30mm diameter hole through the surface they
are to be installed on. Assemble rinse unit socket ensuring the base seal
is in place under body. Attach the tapered end of the flex to the rinse
unit. Check that the Non-Return valve is fitted in the externally threaded
end of the flex. If not, push the Non-return valve into the bore, ensuring
that it is correctly orientated. Pass the flex through the socket, and screw
the externally threaded end to the remaining hose at the base of the
mixer tap.
Before Use
7) Turn on the Hot and Cold supplies to the tap.
8) Carefully check the installation for leaks.
9) If further building work is to be carried out in the vicinity, cover the tap
with a plastic bag to avoid damaging the finish.

9.24410/Blue*
9.24410/Red*
9.26410
9.24305*
9.18380*
9.09422*
9.28401
9.28405
9.26400
9.13362
9.20360*
9.25384
9.17384*
9.07840
9.26400 9.28405
9.18380*
9.25384
9.17384*
9.20384*
9.06401
9.24305*
9.26410
9.12421*
9.13145/Hot
9.13146/Cold
9.09422*
9.24410/Blue*
9.24410/Red*
The Traditional Kitchen Collection
Installation & User Guides
Perrin & Rowe is a registered trademark of Avilion Limited. Gateway XIII, Ferry Lane, Rainham, Essex, RM13 9JY, United Kingdom.
T [phone] F [phone] E [e-mail] W www.avilion.co.uk
904360.E
Exploded Diagram of Phoenician Mixer E.4460 Exploded Diagram of Phoenician Mixer with Rinse E.4360
Operation
Ceramic disc valves are fitted as standard.
Flow from FULLY OFF to FULLY ON is achieved by rotating the
handles a quarter turn.
Guarantee
For written details of the product guarantee, please contact
us at the address shown below.
Spare Parts
For maintenance and repairs, we recommend you employ a
registered plumber. Before ordering spare parts, determine
the correct reference number from the exploded diagram
below. Quote this number, and where appropriate, the
colour of your tap. For spares, please contact your local dis-
tributor or Perrin & Rowe.
Care & Maintenance
Occasional cleaning with warm soapy water, followed by a polish
with a soft cloth is all that is required to keep the plated fin-
ish in good condition.
Do not use proprietary abrasive liquids, powders, or pads to
clean the tap. You will damage the plated finish and void
your guarantee.
The aeration device fitted to the hot/cold water outlet may
need occasional cleaning, especially in hard water areas. This
is accomplished by unscrewing the outlet in an anti-clockwise
direction, dismantling and leaving the inner screen mesh
immersed overnight in vinegar or lemon juice.
DO NOT use chemical descaling liquids for this purpose.
*Specify Colour *Specify Colour
9.19426
9.28426*
9.18425*
9.27426*